Pause flips bank 1 between the cans (36-51) and the movers (84-99). Threshold
flashes the cans on bass hits and is exclusive with Sound, and knob 6 is the
sides' peak. The Sound and Threshold pads light while on, and the colour pads
that were on are pressed again when QLC+ reloads the show. --lock-knobs is gone.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Keep main's Temple of Techno show over dev's older copy from the first venue
workspaces commit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pause toggles bank 1 between the cans and the movers (scripts/shows/mover_bank.py).
Knobs 9-12 (CC 38-41) drive all four movers' pan, tilt, focus and lens
rotate, as in templeoftechno.qxw (scripts/shows/mover_position.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
padcontroller.virtualpad presses pads and sets knobs through padcontroller-in,
refusing unless QLC+ last opened shows/test.qxw. tests/test_e2e_pad.py uses it
to check can and mover colours in the simulator's /api/state (PAD_E2E=1).
pytest is a dev package now, so the plain test functions unittest skipped run
too. test_small_eye.py is a rig tester, not a test, so pytest leaves it alone,
and the #14 direction assertion now matches the stage map (-179).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Sound pad (bank 1 note 36) toggles a QLC+ Audio Triggers widget whose
volume bar drives a Sound submaster beside the can dimmers, so the cans'
brightness follows the music while the movers stay steady. padcontroller sends
CC 100 at full on every press and release of that pad, bypassing its CC
smoothing, so switching sound off always leaves the cans at full.
test.qxw also gains Chase forward/reverse, a double and an opposing zigzag
down the side cans (RGB matrices whose colour follows the Colour 2 pads), a
Strobe flash pad with the cans' strobe channel forced HTP, and the Dimmers
frame, forced-LTP side colours and dimmer-free colour scenes from parallel
sessions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
padcontroller.midi now follows the pad every 2 s: it reopens it after a
replug, moves to USB when that turns up, and re-links QLC+ to the virtual
port after a restart, so QLC+ can stay open. Only the chosen source is
subscribed, so a USB pad no longer gets Bluetooth input as well.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Bank 2's lamp colours come from preset page 7, not page 3, so pad_colours.py
writes there and the editor labels it Bank 2. The factory reset loads the
image MidiSuite uploads for its own reset, and the bank toggle writes the
global-block byte MidiSuite uses to switch banks.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
The record layout and writes come from usbmon captures of MidiSuite:
a pad colour is one three-byte write to its preset address, which lights
the lamp straight away, and Save is the empty write that keeps it after
a power cycle. Pad records are channel, note, min and max velocity, RGB,
then Led. Tempo, swing, pad curve, and transpose come from the global
block, memory type 4. The factory image from MidiSuite's Reset is kept
as a test fixture, and scripts/decode_usbmon.py prints the SysEx in a
capture.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The lamps ignore note messages, so the colours are stored in the preset and committed with the same empty write MidiSuite's Save button sends.
Co-authored-by: Cursor <cursoragent@cursor.com>