The movers layer loses its Strobe (pad 9): its button, its scene and the
forced-HTP strobe channel it needed. Its pad, the rest of the second row
and pad 5 take the five shapes the movers did not have yet: Diamond, Square,
Corners (SquareChoppy), Leaf, and Tilt (Line2 on tilt alone). All nine sit in
the Movement solo frame, one at a time, mirrored and relative to the knobs.
Knob 13's speed dial gives Corners an eighth of its time and the rest a
quarter (scripts/shows/mover_all_efx.py). The pad controller settles the
knobs after all nine.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
They fill the movers layer's top row, pads 15 and 16 (notes 98 and 99), in
the Movement solo frame with Wander and Ballyhoo: a circle of about ±45° of
pan and ±21° of tilt, and a straight pan sweep of about ±60°, both mirrored
and relative to the knobs. Knob 13's speed dial gives them a quarter of its
time, 5.5 s a round to start with (scripts/shows/mover_more_efx.py). The pad
controller settles the knobs after them too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Their two buttons go into a Movement solo frame where they sit, so starting
one stops the other (scripts/shows/mover_movement_solo.py). The pad
controller follows: it tracks the one that is on, and settles the knobs only
when that one goes off. Swapping needs no settle, as the new EFX writes over
the old one's offset.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A Movers speed dial on knob 13 (CC 42), beside the cans' Speed dial, sets
how long Wander takes to go round and gives Ballyhoo an eighth of it
(scripts/shows/mover_speed.py).
QLC+ 4.12 counts an EFX's fade-in inside every round, so Wander has been
taking 22 s and Ballyhoo 2.5 s, not 24 s and 3 s. The dial keeps those as
its starting point and runs from 62 s and 7.5 s fully left to 10 s and 1 s
fully right. The fade-ins stay, so the movers don't jump when either starts.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The movers layer loses its Chase, Chase reverse, Zigzag and Opposing pads,
with their runs, holds, colour matrices, fixture groups and Speed dial
entries. Wander and Ballyhoo move up to pads 13 and 14 (notes 96 and 97),
and the pad controller settles the knobs after those notes instead
(scripts/shows/mover_pads_top_row.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pad 11 on the movers layer (note 94) toggles a fast figure of eight around
the Pan and Tilt knobs, like Wander: about ±85° of pan and ±26° of tilt, all
four movers together so the pairs mirror left to right and front to back
(scripts/shows/mover_ballyhoo.py).
The pad controller now settles the knobs after Ballyhoo goes off as well as
Wander, and keeps track of each separately.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
M3 and M4 are mounted 90° round from M1 and M2, so at pan 0 they face the
middle. Knob 9 now drives a Pan slider for M1 and M2 over 0–212 and a Pan
back slider for M3 and M4 over 43–255 (scripts/shows/mover_pan_back.py).
The same span keeps the pairs 90° of pan apart all the way round: at knob 0
the front pair face the audience and the back pair the back wall, and the
left and right pairs point at the centre and the side walls together.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pad 10 on the movers layer (note 93) toggles a relative EFX that drifts all
four movers around the Pan and Tilt knobs: a 24 s Lissajous of about ±30° pan
and ±10° tilt, each mover a quarter of the way further round, easing in over
2 s (scripts/shows/mover_wander.py).
QLC+ 4.12 leaves a relative EFX's last offset on the movers when it stops,
until the sliders under it change. So when Wander goes off, the pad
controller nudges the Pan and Tilt knobs a step and puts them back, 0.1 s
apart.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The colour scenes leave the dimmers to Level sliders on knobs 15, 5, 7 and 8.
The Chataigne export carries Level sliders and their starting values.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Keep main's Temple of Techno show over dev's older copy from the first venue
workspaces commit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pause toggles bank 1 between the cans and the movers (scripts/shows/mover_bank.py).
Knobs 9-12 (CC 38-41) drive all four movers' pan, tilt, focus and lens
rotate, as in templeoftechno.qxw (scripts/shows/mover_position.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>