M3 and M4 are mounted 90° round from M1 and M2, so at pan 0 they face the
middle. Knob 9 now drives a Pan slider for M1 and M2 over 0–212 and a Pan
back slider for M3 and M4 over 43–255 (scripts/shows/mover_pan_back.py).
The same span keeps the pairs 90° of pan apart all the way round: at knob 0
the front pair face the audience and the back pair the back wall, and the
left and right pairs point at the centre and the side walls together.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pad 10 on the movers layer (note 93) toggles a relative EFX that drifts all
four movers around the Pan and Tilt knobs: a 24 s Lissajous of about ±30° pan
and ±10° tilt, each mover a quarter of the way further round, easing in over
2 s (scripts/shows/mover_wander.py).
QLC+ 4.12 leaves a relative EFX's last offset on the movers when it stops,
until the sliders under it change. So when Wander goes off, the pad
controller nudges the Pan and Tilt knobs a step and puts them back, 0.1 s
apart.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
On Bluetooth there is no Private port, so every Sound or Threshold press
opened two sequencer clients to light the lamps and left them open when the
port lookup raised. After 29 presses the sequencer was full and aconnect
could no longer open it. set_sound_lamps and Link now close both clients
on that path too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The colour scenes leave the dimmers to Level sliders on knobs 15, 5, 7 and 8.
The Chataigne export carries Level sliders and their starting values.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pause flips bank 1 between the cans (36-51) and the movers (84-99). Threshold
flashes the cans on bass hits and is exclusive with Sound, and knob 6 is the
sides' peak. The Sound and Threshold pads light while on, and the colour pads
that were on are pressed again when QLC+ reloads the show. --lock-knobs is gone.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Keep main's Temple of Techno show over dev's older copy from the first venue
workspaces commit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pause toggles bank 1 between the cans and the movers (scripts/shows/mover_bank.py).
Knobs 9-12 (CC 38-41) drive all four movers' pan, tilt, focus and lens
rotate, as in templeoftechno.qxw (scripts/shows/mover_position.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Bank 2's lamp colours come from preset page 7, not page 3, so pad_colours.py
writes there and the editor labels it Bank 2. The factory reset loads the
image MidiSuite uploads for its own reset, and the bank toggle writes the
global-block byte MidiSuite uses to switch banks.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
The record layout and writes come from usbmon captures of MidiSuite:
a pad colour is one three-byte write to its preset address, which lights
the lamp straight away, and Save is the empty write that keeps it after
a power cycle. Pad records are channel, note, min and max velocity, RGB,
then Led. Tempo, swing, pad curve, and transpose come from the global
block, memory type 4. The factory image from MidiSuite's Reset is kept
as a test fixture, and scripts/decode_usbmon.py prints the SysEx in a
capture.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The lamps ignore note messages, so the colours are stored in the preset and committed with the same empty write MidiSuite's Save button sends.
Co-authored-by: Cursor <cursoragent@cursor.com>
The Windows app builds the flash save when it runs, so the script reads that build and reports the method instead of guessing a packet.
Co-authored-by: Cursor <cursoragent@cursor.com>
Learn pad and knob banks into shows/midi_map.json, then print pad and knob numbers with relative encoder steps.
Co-authored-by: Cursor <cursoragent@cursor.com>
Floor 8 stays on the live ground aim; Wall 8 uses the Here–Out box. Pan/tilt speed is a slider so it matches Bright and Focus.
Co-authored-by: Cursor <cursoragent@cursor.com>
Generate the board from a script so looks, positions, and figure-8s stay in one place instead of being edited by hand in QLC+.
Co-authored-by: Cursor <cursoragent@cursor.com>
Group workspaces, generators, stage map, and tests into clear folders, and add the unified cans+movers show plus a simple shared/individual RGBW control board.
Co-authored-by: Cursor <cursoragent@cursor.com>