Each panel's subtitle gives the buttons: PAD BANK and KNOB BANK pick the
banks, Pause puts pad bank 1 on the movers, and holding Play moves pad bank 2
to Colour 2.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
shows/test-pads.png shows both banks of pads on every layer (bank 1 on the
cans and, with Pause, the movers; bank 2 as Colour 1 and, with Play held,
Colour 2) and what each knob does. scripts/shows/draw_test_pads.py reads the
labels and colours from the show's virtual console, so running it again
brings the picture up to date.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The layout, chase colours, mover speeds and levels as saved from QLC+: the
colour frames stacked on the left with the cans and movers pads beside them.
The Colour 1 and Colour 2 buttons are 75 px squares, and the Chase runs and
Pads layer frames below Colour 2 move down to clear them
(scripts/shows/square_colours.py). The Movers speed dial comes in from
x=1820 to beside Movers position, and both speed dials are trimmed to the
dial and its time.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A Pads layer frame under the movers pads has Cans pads and Movers pads
buttons (scripts/shows/layer_indicator.py). The pad controller holds channel
16 note 0 (cans) or 1 (movers) down and the other up whenever Pause changes,
QLC+ reloads or it starts, and the Flash buttons light while their note is
held, so the lit one is the layer and a missed message can't leave them the
wrong way round. Each flashes an empty scene of its own: with one between
them, QLC+ lit both.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Each chase was two buttons on one pad note: the pads frame's ran the side
dimmer hold under Peak, and the Chase runs frame's ran the stripe outside it.
The pad pressed both; a click pressed only the hold, which lit nothing. Now
the pads frame's button runs a hold of the chase's own whose step is the Sides
dimmer and a Script that starts the stripe. Peak reaches the dimmer through the
chaser and collection but not the stripe through the script, as with the pad
(scripts/shows/chase_clicks.py). The Chase runs buttons no longer listen to the
pad.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Eight of make_cabaret_vc.py's Can Patterns on the cans pads 1-8, in a Can
patterns solo frame in place of the pads frame's empty Buttons 53-60:
Theater, Rainbow, Odd Even, Left Right, Scanner (with a fading tail), Fill,
Center and Pairs, laid out for the test show's cans and walking the ring round
the room (scripts/shows/can_patterns.py). Collapse and Chase Out are left out.
The masks show the Colour 1 colour; Odd Even (a checkerboard) and Left Right
swap between Colour 1 and Colour 2 through four Matrix widgets in the Chase
colours frame. All of them follow the cans' Speed dial (knob 1). Each pattern is
RGB matrices running from start to stop (rgbscripts/steps.js and swap.js, linked
into ~/.qlcplus/rgbscripts), so a chase started over one lands on top, and the
pad controller restarts the pattern that is on just after a Colour 1 press so
the new colour scene doesn't cover it.
The row of 4 (#3-#6) never animates; CLAUDE.md now says so for whatever comes
next.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Sound and Threshold audio triggers go, with the Sound submaster beside the
cans' Front and Back sliders (CC 100) and the Sound peak frame with its Peak
submaster and Hit button and the Cans hit functions only Hit ran. Pads 1 and 2
are plain spare buttons again (scripts/shows/drop_sound.py). The pads frame's
own Peak (knob 6) stays: it is the chases' peak.
The pad controller drops its side of it: the Pump and Threshold modes, the
CC 100 resets, holding the side knobs at the peak and the pad lamps that showed
which mode was on. Pads 1 and 2 and knobs 5, 6 and 8 pass straight through.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Corners slammed the heads about 100° of pan every 0.6 s at full motor speed.
It now runs at a quarter of the speed dial like the other shapes, about 1.4 s
a corner, and its pad starts a collection with a Movers glide scene that sets
the heads' Pan/Tilt Speed to 40 while it runs, so they ease into each corner.
That channel is forced HTP on the movers, so it drops back to full speed when
Corners stops instead of QLC+ holding it for everything after
(scripts/shows/mover_corners_glide.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The movers layer loses its Strobe (pad 9): its button, its scene and the
forced-HTP strobe channel it needed. Its pad, the rest of the second row
and pad 5 take the five shapes the movers did not have yet: Diamond, Square,
Corners (SquareChoppy), Leaf, and Tilt (Line2 on tilt alone). All nine sit in
the Movement solo frame, one at a time, mirrored and relative to the knobs.
Knob 13's speed dial gives Corners an eighth of its time and the rest a
quarter (scripts/shows/mover_all_efx.py). The pad controller settles the
knobs after all nine.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
They fill the movers layer's top row, pads 15 and 16 (notes 98 and 99), in
the Movement solo frame with Wander and Ballyhoo: a circle of about ±45° of
pan and ±21° of tilt, and a straight pan sweep of about ±60°, both mirrored
and relative to the knobs. Knob 13's speed dial gives them a quarter of its
time, 5.5 s a round to start with (scripts/shows/mover_more_efx.py). The pad
controller settles the knobs after them too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Their two buttons go into a Movement solo frame where they sit, so starting
one stops the other (scripts/shows/mover_movement_solo.py). The pad
controller follows: it tracks the one that is on, and settles the knobs only
when that one goes off. Swapping needs no settle, as the new EFX writes over
the old one's offset.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A Movers speed dial on knob 13 (CC 42), beside the cans' Speed dial, sets
how long Wander takes to go round and gives Ballyhoo an eighth of it
(scripts/shows/mover_speed.py).
QLC+ 4.12 counts an EFX's fade-in inside every round, so Wander has been
taking 22 s and Ballyhoo 2.5 s, not 24 s and 3 s. The dial keeps those as
its starting point and runs from 62 s and 7.5 s fully left to 10 s and 1 s
fully right. The fade-ins stay, so the movers don't jump when either starts.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The movers layer loses its Chase, Chase reverse, Zigzag and Opposing pads,
with their runs, holds, colour matrices, fixture groups and Speed dial
entries. Wander and Ballyhoo move up to pads 13 and 14 (notes 96 and 97),
and the pad controller settles the knobs after those notes instead
(scripts/shows/mover_pads_top_row.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pad 11 on the movers layer (note 94) toggles a fast figure of eight around
the Pan and Tilt knobs, like Wander: about ±85° of pan and ±26° of tilt, all
four movers together so the pairs mirror left to right and front to back
(scripts/shows/mover_ballyhoo.py).
The pad controller now settles the knobs after Ballyhoo goes off as well as
Wander, and keeps track of each separately.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
M3 and M4 are mounted 90° round from M1 and M2, so at pan 0 they face the
middle. Knob 9 now drives a Pan slider for M1 and M2 over 0–212 and a Pan
back slider for M3 and M4 over 43–255 (scripts/shows/mover_pan_back.py).
The same span keeps the pairs 90° of pan apart all the way round: at knob 0
the front pair face the audience and the back pair the back wall, and the
left and right pairs point at the centre and the side walls together.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pad 10 on the movers layer (note 93) toggles a relative EFX that drifts all
four movers around the Pan and Tilt knobs: a 24 s Lissajous of about ±30° pan
and ±10° tilt, each mover a quarter of the way further round, easing in over
2 s (scripts/shows/mover_wander.py).
QLC+ 4.12 leaves a relative EFX's last offset on the movers when it stops,
until the sliders under it change. So when Wander goes off, the pad
controller nudges the Pan and Tilt knobs a step and puts them back, 0.1 s
apart.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A Speed dial on knob 1 (CC 30) sets the step time of the cans' and movers'
chase and zigzag runs, from 800 ms fully left to 50 ms fully right, starting
at the old 200 ms. Zigzag forward stays at half the step, and the dimmer holds
follow at 8 steps so they stretch with the run. The 500 ms trail is unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The front right mover is on DMX 1 and the front left on 45, so M1 and M2
swap addresses in the stage map and test.qxw. Measured on the rig, pan 0
faces forward on the front pair and into the middle on the back pair, back
at 85. M1 and M4 turn anticlockwise, so movers get a pan_reverse flag.
Tilt 127 now points straight down: the simulator draws a spot under the
head, and past 127 the beam flips behind the pan heading.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Dimmers sliders are now Middle, Front and Back, and the movers' Brightness
(knob 15) leads the Movers position frame.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The colour scenes leave the dimmers to Level sliders on knobs 15, 5, 7 and 8.
The Chataigne export carries Level sliders and their starting values.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Keep main's Temple of Techno show over dev's older copy from the first venue
workspaces commit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pause toggles bank 1 between the cans and the movers (scripts/shows/mover_bank.py).
Knobs 9-12 (CC 38-41) drive all four movers' pan, tilt, focus and lens
rotate, as in templeoftechno.qxw (scripts/shows/mover_position.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Sound pad (bank 1 note 36) toggles a QLC+ Audio Triggers widget whose
volume bar drives a Sound submaster beside the can dimmers, so the cans'
brightness follows the music while the movers stay steady. padcontroller sends
CC 100 at full on every press and release of that pad, bypassing its CC
smoothing, so switching sound off always leaves the cans at full.
test.qxw also gains Chase forward/reverse, a double and an opposing zigzag
down the side cans (RGB matrices whose colour follows the Colour 2 pads), a
Strobe flash pad with the cans' strobe channel forced HTP, and the Dimmers
frame, forced-LTP side colours and dimmer-free colour scenes from parallel
sessions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMC-PAD knobs drive aim, focus, and brightness, floor fixtures sit on the gateway universe, and the Small Eye map matches the channels the show writes.
Co-authored-by: Cursor <cursoragent@cursor.com>
Learn pad and knob banks into shows/midi_map.json, then print pad and knob numbers with relative encoder steps.
Co-authored-by: Cursor <cursoragent@cursor.com>
Floor 8 stays on the live ground aim; Wall 8 uses the Here–Out box. Pan/tilt speed is a slider so it matches Bright and Focus.
Co-authored-by: Cursor <cursoragent@cursor.com>
Generate the board from a script so looks, positions, and figure-8s stay in one place instead of being edited by hand in QLC+.
Co-authored-by: Cursor <cursoragent@cursor.com>
Group workspaces, generators, stage map, and tests into clear folders, and add the unified cans+movers show plus a simple shared/individual RGBW control board.
Co-authored-by: Cursor <cursoragent@cursor.com>