A Pads layer frame under the movers pads has Cans pads and Movers pads
buttons (scripts/shows/layer_indicator.py). The pad controller holds channel
16 note 0 (cans) or 1 (movers) down and the other up whenever Pause changes,
QLC+ reloads or it starts, and the Flash buttons light while their note is
held, so the lit one is the layer and a missed message can't leave them the
wrong way round. Each flashes an empty scene of its own: with one between
them, QLC+ lit both.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The SMC-PAD latches Pause itself: one message a press, 127 and 0 on
alternate presses, nothing on release. The pad controller flipped the layer
only on 127, so every second press did nothing. Bank 1 now follows the
value: 0 is the cans, 127 the movers.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Eight of make_cabaret_vc.py's Can Patterns on the cans pads 1-8, in a Can
patterns solo frame in place of the pads frame's empty Buttons 53-60:
Theater, Rainbow, Odd Even, Left Right, Scanner (with a fading tail), Fill,
Center and Pairs, laid out for the test show's cans and walking the ring round
the room (scripts/shows/can_patterns.py). Collapse and Chase Out are left out.
The masks show the Colour 1 colour; Odd Even (a checkerboard) and Left Right
swap between Colour 1 and Colour 2 through four Matrix widgets in the Chase
colours frame. All of them follow the cans' Speed dial (knob 1). Each pattern is
RGB matrices running from start to stop (rgbscripts/steps.js and swap.js, linked
into ~/.qlcplus/rgbscripts), so a chase started over one lands on top, and the
pad controller restarts the pattern that is on just after a Colour 1 press so
the new colour scene doesn't cover it.
The row of 4 (#3-#6) never animates; CLAUDE.md now says so for whatever comes
next.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Sound and Threshold audio triggers go, with the Sound submaster beside the
cans' Front and Back sliders (CC 100) and the Sound peak frame with its Peak
submaster and Hit button and the Cans hit functions only Hit ran. Pads 1 and 2
are plain spare buttons again (scripts/shows/drop_sound.py). The pads frame's
own Peak (knob 6) stays: it is the chases' peak.
The pad controller drops its side of it: the Pump and Threshold modes, the
CC 100 resets, holding the side knobs at the peak and the pad lamps that showed
which mode was on. Pads 1 and 2 and knobs 5, 6 and 8 pass straight through.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The movers layer loses its Strobe (pad 9): its button, its scene and the
forced-HTP strobe channel it needed. Its pad, the rest of the second row
and pad 5 take the five shapes the movers did not have yet: Diamond, Square,
Corners (SquareChoppy), Leaf, and Tilt (Line2 on tilt alone). All nine sit in
the Movement solo frame, one at a time, mirrored and relative to the knobs.
Knob 13's speed dial gives Corners an eighth of its time and the rest a
quarter (scripts/shows/mover_all_efx.py). The pad controller settles the
knobs after all nine.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
They fill the movers layer's top row, pads 15 and 16 (notes 98 and 99), in
the Movement solo frame with Wander and Ballyhoo: a circle of about ±45° of
pan and ±21° of tilt, and a straight pan sweep of about ±60°, both mirrored
and relative to the knobs. Knob 13's speed dial gives them a quarter of its
time, 5.5 s a round to start with (scripts/shows/mover_more_efx.py). The pad
controller settles the knobs after them too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Their two buttons go into a Movement solo frame where they sit, so starting
one stops the other (scripts/shows/mover_movement_solo.py). The pad
controller follows: it tracks the one that is on, and settles the knobs only
when that one goes off. Swapping needs no settle, as the new EFX writes over
the old one's offset.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The movers layer loses its Chase, Chase reverse, Zigzag and Opposing pads,
with their runs, holds, colour matrices, fixture groups and Speed dial
entries. Wander and Ballyhoo move up to pads 13 and 14 (notes 96 and 97),
and the pad controller settles the knobs after those notes instead
(scripts/shows/mover_pads_top_row.py).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pad 11 on the movers layer (note 94) toggles a fast figure of eight around
the Pan and Tilt knobs, like Wander: about ±85° of pan and ±26° of tilt, all
four movers together so the pairs mirror left to right and front to back
(scripts/shows/mover_ballyhoo.py).
The pad controller now settles the knobs after Ballyhoo goes off as well as
Wander, and keeps track of each separately.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pad 10 on the movers layer (note 93) toggles a relative EFX that drifts all
four movers around the Pan and Tilt knobs: a 24 s Lissajous of about ±30° pan
and ±10° tilt, each mover a quarter of the way further round, easing in over
2 s (scripts/shows/mover_wander.py).
QLC+ 4.12 leaves a relative EFX's last offset on the movers when it stops,
until the sliders under it change. So when Wander goes off, the pad
controller nudges the Pan and Tilt knobs a step and puts them back, 0.1 s
apart.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pause flips bank 1 between the cans (36-51) and the movers (84-99). Threshold
flashes the cans on bass hits and is exclusive with Sound, and knob 6 is the
sides' peak. The Sound and Threshold pads light while on, and the colour pads
that were on are pressed again when QLC+ reloads the show. --lock-knobs is gone.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Sound pad (bank 1 note 36) toggles a QLC+ Audio Triggers widget whose
volume bar drives a Sound submaster beside the can dimmers, so the cans'
brightness follows the music while the movers stay steady. padcontroller sends
CC 100 at full on every press and release of that pad, bypassing its CC
smoothing, so switching sound off always leaves the cans at full.
test.qxw also gains Chase forward/reverse, a double and an opposing zigzag
down the side cans (RGB matrices whose colour follows the Colour 2 pads), a
Strobe flash pad with the cans' strobe channel forced HTP, and the Dimmers
frame, forced-LTP side colours and dimmer-free colour scenes from parallel
sessions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>