firmware < V7.x)
* jtagmkII.c: When going to write to the boot section of flash,
use MTYPE_BOOT_FLASH rather than MTYPE_FLASH
* jtagmkII_private.h: add MTYPE_BOOT_FLASH constant
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1077 81a1dc3b-b13d-400b-aceb-764788c761c2
supported error
* stk500v2.c: Handle all Xmega memory sections (except
"prodsig" which is not documented in AVR079)
* fileio.c: Treat the "boot", "application", and "apptable"
regions (which are actually subregions of "flash") all as
being flash, i.e. suppress trailing 0xFF bytes when reading
them
* avr.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1075 81a1dc3b-b13d-400b-aceb-764788c761c2
"GO" code in again, but only activate it when programming an
Xmega device through PDI.
Wonderfully consistent tools.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1071 81a1dc3b-b13d-400b-aceb-764788c761c2
turned out to do more harm than good; on the Xmega, it caused exactly
the opposite reaction, the CPU stopped. Even without it, after the
RESET command, the target is running already. So, drop the GO.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1070 81a1dc3b-b13d-400b-aceb-764788c761c2
nounput. This gets rid of a compiler warning, so we are warning-free
again.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1048 81a1dc3b-b13d-400b-aceb-764788c761c2
trying to hard-code the default port name in main.c.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1047 81a1dc3b-b13d-400b-aceb-764788c761c2
to lusb0_usb.h (for whatever reason). Autoprobe for the filename
during configure, and include whatever is appropriate.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1043 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #35208: avrdude 5.11 on freebsd 8.2-STABLE does not reset
Arduino Uno properly
* arduino.c (arduino_open): Bump the timeout between pulling
the DTR and RTS lines low and high.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1036 81a1dc3b-b13d-400b-aceb-764788c761c2
non-standard baud rates (only baud rates up to B38400 are
standardized by the Single UNIX Specification).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1029 81a1dc3b-b13d-400b-aceb-764788c761c2
(Extended Linear Address Record)
Replace the change from r928 (handling of 0x8000000 offset in AVR32
files) by a completely different logic that no longer breaks hex files
for other devices starting with an offset; also apply a similar change
to S-record files, as well as when writing files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1017 81a1dc3b-b13d-400b-aceb-764788c761c2
it has been explicitly requested (by -y or -Y), rather than always
attempting to read the last EEPROM bytes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1014 81a1dc3b-b13d-400b-aceb-764788c761c2
Fix regression in the AVRISPmkII/STK600 TPI handling introduced
by the USBasp's TPI implementation which added a pagesize even for
the minor memory regions of TPI devices. Also fix wrong offset
introduced by the memory tagging patch.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1009 81a1dc3b-b13d-400b-aceb-764788c761c2
their programmer doesn't provide a (low-level) cmd_tpi method;
instead, fall back to the normal programmer methods which are
supposed to handle the situation.
This fixes a regression where the recent bitbang-TPI implementation
broke TPI handling of STK600/AVRISPmkII.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1008 81a1dc3b-b13d-400b-aceb-764788c761c2
Each memory image byte is now tagged as it's being read from a file.
Only bytes read from a file will be written or verified (modulo page
granularity requirements).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1007 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk500v2_initialize): For the AT90S1200, release
/RESET for a moment before reinitializing, as this is required by
its programming protocol.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1004 81a1dc3b-b13d-400b-aceb-764788c761c2
than ftdi_init(), as this is a more specific thing to search for in
order to make sure getting a recent enough libftdi.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1003 81a1dc3b-b13d-400b-aceb-764788c761c2
programmers)
* config_gram.y: Introduce new keyword "is_at90s1200".
* lexer.l: (Ditto.)
* avrdude.conf.in: Applew new keyword to the AT90S1200 device.
* avrpart.h: Introduce new flag AVRPART_IS_AT90S1200, reflecting
the is_at90s1200 configuration keyword.
* bitbang.c (bitbang_initialize): Replace existing test for
AT90S1200 by AVRPART_IS_AT90S1200
* avr.c (avr_write_byte_default): Avoid the pre-write reading for
the AT90S1200, as this appears to sometimes corrupt the high byte
by pre-programming the low byte just written into it.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1002 81a1dc3b-b13d-400b-aceb-764788c761c2
"native" into "LF", in the hope this might cause less confusion to
some shells running on non-Unix systems.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1001 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7056: adding support for mikrokopter bootloader to butterfly
* butterfly.c: Add some specific logic to handle the
mikrokopter.de butterfly bootloader.
* butterfly.h: Add one related function declaration.
* config_gram.y: Add butterfly_mk keyword.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add entry for butterfly_mk.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@991 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf (jtagkey): Add a definition for the Amontec
JTAGKey
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@986 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #22720: avrdude-5.5 ignores buff settings in avrdude.conf
(Note that the actual bug the subject is about has been fixed
long ago.)
* update.c (do_op): fix a diagnostic message
* pgm.h: add exit_datahigh field
* par.c: set and act upon the exit_datahigh field
* avrdude.1: document the new -E options
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@985 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtagII.c (jtagmkII_getsync): Instead of exit()ing from
deep within the tree when detecting the "need debugWIRE"
situation, properly pass this up as a return code.
* jtagII_private.h (JTAGII_GETSYNC_FAIL_GRACEFUL): New constant.
* stk500v2.c (stk500v2_jtagmkII_open): Don't tell anything
anymore when receiving a JTAGII_GETSYNC_FAIL_GRACEFUL from
jtagmkII_getsync(); silently give up (all necessary has been
said already).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@983 81a1dc3b-b13d-400b-aceb-764788c761c2
* usbasp.c (libusb_to_errno): Conditionalize some error codes
that apparently are lacking on MinGW.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@982 81a1dc3b-b13d-400b-aceb-764788c761c2
* ser_avrdoper.c: add <stdlib.h> so exit() is declared.
* usbtiny.c (usbtiny_open): provide an initializer to a
"may be used uninitialized" variable (since GCC could not
fully detect the logic behind).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@981 81a1dc3b-b13d-400b-aceb-764788c761c2
Wolfgang Moser, Ville Voipio, Hannes Weisbach
patch #7486: Patch to add FT2232C/D, FT2232H, FT4232H,
usbvid, usbpid, usbdev for USB support - Based on #7062
* avrftdi.c: New file.
* avrftdi.h: (Ditto.)
* configure.ac: Add check for libftdi.
* config_gram.y: Add AVRFTDI and per-programmer USB string
keywords.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add avrftdi and 2232HIO programmers.
* pgm.h: Add USB parameters.
* Makefile.am: Add avrftdi.c and avrftdi.h.
* AUTHORS: Mention the new authors.
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@979 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #31779: Add support for addressing usbtinyisp with -P option
* usbtiny.c (usbtiny_open): Add logic to distinguish multiple USBtinyISP
programmers by their bus:device tuple.
* doc/avrdude.texi: Document the new functionality.
* avrdude.1: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@974 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #30268: Debugwire broken in avrdude-5.10
* jtagmkII.c (jtagmkII_initialize): only try setting up a JTAG chain when
the programmer is using JTAG.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@973 81a1dc3b-b13d-400b-aceb-764788c761c2
on the AVRISP-MKII
* stk500v2.c (stk500v2_program_enable): Rewrite the logic to
explain ISP activation failures.
* stk500v2_private.h: Fix the various STATUS_* constants;
AVR069 and AVR079 disagreed in their values, even though they
are apparently implementing the same logic behind.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@972 81a1dc3b-b13d-400b-aceb-764788c761c2
ATtiny88, ATmega168, ATmega168P, ATmega328P): Bump delay value for STK500v2
EEPROM write operation to 5, according to the respective XML files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@970 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #31386: A "BUILD.svn" or similar "how to get started" doc would be helpful
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@967 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #32539: [Documentation][Patch] Man page is misleading re: Dragon & PDI
Update information about PDI connections on AVR Dragon
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@966 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #33345: File auto detection as binary doesn't open
file in binary mode on Windows
* fileio.c: Move the decision about opening files in
binary mode until before the fopen() call.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@964 81a1dc3b-b13d-400b-aceb-764788c761c2
no longer experience the day-to-day incompatibilities we've been faced
with some 5+ years ago.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@960 81a1dc3b-b13d-400b-aceb-764788c761c2
timeout should depend on the selected clock speed, but changing the
API for that would require quite some effort throughout the entire
code base.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@954 81a1dc3b-b13d-400b-aceb-764788c761c2
programming stability, in particular with the STK600.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@952 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk500v2_open): use same condition to refer to the AVR
Doper support as used in the definition in ser_avrdoper.c.
(Thanks to Christian Starkjohann for the analysis of the problem.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@947 81a1dc3b-b13d-400b-aceb-764788c761c2
doc/avrdude.texi (Troubleshooting): Mention the libusb 0.1 API
wrapper issue that is present in some Linux versions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@944 81a1dc3b-b13d-400b-aceb-764788c761c2
* doc/avrdude.texi: Remove the recommendation for building
Win32 binaries under Cygwin; mention MinGW as an alternative
environment.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@942 81a1dc3b-b13d-400b-aceb-764788c761c2
* windows/Makefile.am (loaddrv_LDFLAGS): remove, the -mno-cygwin
flag is supposed to be set in CFLAGS by ./configure
* configure.ac: add a check for the presence of usleep(), add a
check whether the linker accepts -static
* avrdude.h: protect prototype for usleep by !defined(HAVE_USLEEP)
* ppwin.c (usleep): protect by !defined(HAVE_USLEEP)
* main.c: silence "array subscript of type char" compiler warnings
by casting all arguments to tolower()/toupper() and isspace()/
isdigit()/ispunct() to "int"
* butterfly.c: (Dito.)
* avr910.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@936 81a1dc3b-b13d-400b-aceb-764788c761c2
* configure.ac: For Win32 environments, add a check whether the
compiler understands the -mno-cygwin option. If not, don't use
it but suggest using a different compiler.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@930 81a1dc3b-b13d-400b-aceb-764788c761c2
0x10000 bytes
* fileio.c: Revert the changes from r851 and r880, respectively.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@928 81a1dc3b-b13d-400b-aceb-764788c761c2
external reset applied (in case the target is in sleep mode or has
asserted the JTD bit).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@926 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #28611: -i delay not being applied to all serial port
bit banging state transitions
* serbb_win32.c: Apply ispdelay everywhere.
* serbb_posix.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@917 81a1dc3b-b13d-400b-aceb-764788c761c2
Add ATtiny4/5/9/10 to avrdude.conf.in.
Document TPI and new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@916 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6927: Documentation patches
* doc/avrdude.texi: Fix various typos, and remove the last
remnants of obsoleted options -i/-o/-m/-f.
* avrdude.1: Merge typo fixes from avrdude.texi where
applicable.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@914 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch