* jtag3.c (jtag3_read_byte, jtag3_write_byte): Correctly apply the
relevant part of mem->offset as the address to operate on.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1201 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #35800: Compilation error on certain systems if parport is disabled
* linux_ppdev.h: Conditionalize inclusion of <linux/parport.h> and
<linux/ppdev.h> on HAVE_PARPORT
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1198 81a1dc3b-b13d-400b-aceb-764788c761c2
* buspirate.c: Turn the "cmd" argument of the various methods into
a "const unsigned char *"; while doing this, declare all arrays being
passed as arguments to be pointers rather than arrays, as the latter
obfuscates the way arrays are being passed to a callee in C.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1196 81a1dc3b-b13d-400b-aceb-764788c761c2
to upload an invalid Intel HEX file
* fileio.c (ihex2b): Turn the "No end of file record found" warning
into an error if no valid record was found at all.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1195 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #38713: Compilation of the documentation breaks with texinfo-5
* doc/avrdude.texi: Turn @itemx into @item, add @headitem to STK600
Routing/Socket card table
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1194 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk600_xprog_page_erase): Fix argument that is
passed to stk600_xprog_memtype()
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1188 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7876 JTAGICE mkII fails to connect to attiny if debugwire
is enabled AND target has a very slow clock
* jtagmkII.c (jtagmkII_getsync): When leaving debugWIRE mode
temporarily, immediately retry with ISP, rather than leaving.
* stk500v2 (stk500v2_program_enable): Implemented similar logic
for the JTAGICE3.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1183 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtagmkII.c (jtagmkII_initialize): For Xmega devices, and
firmware >= 7.x, don't trigger a RESET, in order to work around a
firmware bug that appears to be present in at least firmware 7.24
for the Dragon.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1125 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Add "jtag3isp" programmer
* jtag3.c: jtag3_setparm() is now public
* jtag3.h: (Dito)
* stk500v2_private.h: Command 0x1D is CMD_SPI_MULTI only
for STK500v2, AVRISPmkII, and JTAGICEmkII; for JTAGICE3,
it's CMD_SET_SCK now; also add CMD_GET_SCK
* avrpart.c (avr_get_output_index): New function
* avrpart.h: (Dito)
* stk500v2.c: Implement the pasthrough programmer glue logic
for JTAGICE3 in ISP mode
* stk500v2.h: (Dito)
* avrdude.1: Document the JTAGICE3 support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1119 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Fix page sizes for all Xmega devices,
by cross-checking against Atmel Studio's device XML files
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1112 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI and JTAG).
* jtagmkII.c (jtagmkII_set_xmega_params): Use "fuse1" rather
than "fuse0" memory space to fill in the NVM offset from, as
there is no "fuse0" on some Xmega devices.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1111 81a1dc3b-b13d-400b-aceb-764788c761c2
traces made by Knut Schwichtenberg, and by similarity to
JTAGICEmkII.
Still quite incomplete, just megaAVR/JTAG is done by now.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1109 81a1dc3b-b13d-400b-aceb-764788c761c2
* main.c: after locating the part information, determine default
memtype for all update options that didn't have a memtype
specified; this is "application" for Xmega parts, and "flash" for
everything else.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1086 81a1dc3b-b13d-400b-aceb-764788c761c2
read device signature
* main.c: When reading the signature yields 0x000000 or 0xffffff,
retry (up to twice) after some progressive delay.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1084 81a1dc3b-b13d-400b-aceb-764788c761c2
ATxmega128D4): New devices. As Xmega D doesn't feature a fuse0
memory cell, move that one out from the generic .xmega part into
the individual Xmega A parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1083 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_initialize): Insert dummy values for PAGEL and
BS2 if they are not present in the config file, in order to be able
to proceed with the stk500_set_extended_parms() anyway.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1082 81a1dc3b-b13d-400b-aceb-764788c761c2
firmware >= V7.x)
* jtagmkII.c: Add firmware-version dependent handling of Xmega parameters.
V7.x firmware expects the NVM offsets being specified through the Xmega
parameters command, but left out as part of the memory address itself.
* jtagmkII_private.h: Add CMND_SET_XMEGA_PARAMS, and struct xmega_device_desc.
* config_gram.y: Add mcu_base keyword.
* avrpart.h: (Dito.)
* lexer.l: (Dito.)
* avrdude.conf.in (.xmega): add mcu_base, and data memory segment.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1078 81a1dc3b-b13d-400b-aceb-764788c761c2
supported error
* stk500v2.c: Handle all Xmega memory sections (except
"prodsig" which is not documented in AVR079)
* fileio.c: Treat the "boot", "application", and "apptable"
regions (which are actually subregions of "flash") all as
being flash, i.e. suppress trailing 0xFF bytes when reading
them
* avr.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1075 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7056: adding support for mikrokopter bootloader to butterfly
* butterfly.c: Add some specific logic to handle the
mikrokopter.de butterfly bootloader.
* butterfly.h: Add one related function declaration.
* config_gram.y: Add butterfly_mk keyword.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add entry for butterfly_mk.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@991 81a1dc3b-b13d-400b-aceb-764788c761c2
Wolfgang Moser, Ville Voipio, Hannes Weisbach
patch #7486: Patch to add FT2232C/D, FT2232H, FT4232H,
usbvid, usbpid, usbdev for USB support - Based on #7062
* avrftdi.c: New file.
* avrftdi.h: (Ditto.)
* configure.ac: Add check for libftdi.
* config_gram.y: Add AVRFTDI and per-programmer USB string
keywords.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add avrftdi and 2232HIO programmers.
* pgm.h: Add USB parameters.
* Makefile.am: Add avrftdi.c and avrftdi.h.
* AUTHORS: Mention the new authors.
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@979 81a1dc3b-b13d-400b-aceb-764788c761c2
* configure.ac: For Win32 environments, add a check whether the
compiler understands the -mno-cygwin option. If not, don't use
it but suggest using a different compiler.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@930 81a1dc3b-b13d-400b-aceb-764788c761c2
Add ATtiny4/5/9/10 to avrdude.conf.in.
Document TPI and new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@916 81a1dc3b-b13d-400b-aceb-764788c761c2
conditional compilation of usb_reset() introduced in r798.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@841 81a1dc3b-b13d-400b-aceb-764788c761c2
support it
Do not call pgm->perform_osccal() unless it is != 0.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@822 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (ATxmega256A3): new device.
* stk500v2 (stk500v2_initialize): Enable the AVRISPmkII as a
PDI-capable device for ATxmega parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@809 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #24749: add support for '328p
* avrdude.conf.in (ATmega328P): new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@796 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6261: avrdude won't use dragon/debugwire to write a file
to eeprom
* jtagmkII.c (jtagmkII_paged_write): when in debugWire mode,
implement a paged write to EEPROM as a series of byte writes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@792 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6542: paged_load fails on the MIB510 programming board
* stk500.c: Add a workaround for the different signon sequence on
MIB510 programmers.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@791 81a1dc3b-b13d-400b-aceb-764788c761c2
for Xmega programming using the JTAG ICE mkII in JTAG mode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@780 81a1dc3b-b13d-400b-aceb-764788c761c2
allow to continue with -F if it failed yet do not attempt to
perform anything on the device itself. That way, -tF could be
specified for programmers like the STK500/STK600 even without a
device connected, just in order to allow changing parameters on
the programmer itself.
* avrdude.1: Document that possible use of the -F option.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@779 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI mode of the STK600 is supported. Single-byte EEPROM
(and flash) updates do not work yet.
* avr.c: "boot" memory is a candidate memory region for paged
operations, besides "flash" and "eeprom".
* avrdude.conf.in: add ATxmega128A1 and ATxmega128A1revD
* avrpart.h: add the AVRPART_HAS_PDI flag (used to distinguish
ATxmega parts from classic AVRs), the nvm_base part field, and
the offset field for a memory region.
* config_gram.y: add "has_pdi", "nvm_base", and "offset"
* lexer.l: (Ditto.)
* main.c: disable auto_erase for ATxmega parts
* stk500v2.c: implement the XPROG functionality, and divert to
this for ATxmega parts
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@777 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6501: New autotools support for avrdude
* Makefile.am: add @WINDOWS_DIRS@ to SUBDIR
* bootstrap: allow for autconf-2.61 and automake-1.10, too
* configure.ac: fix @WINDOWS_DIRS@ recursion, replace
AC_PROG_CC by AM_PROG_CC_C_O, for esoteric reasons
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@774 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6074: added support for crossbow's MIB510 programmer
* avrdude.conf.in: Add entry for mib510.
* stk500.c: Add special hooks to handle the MIB510 programmer.
It mostly talks STK500v1 protocol but has a special hello and
goodbye sequence, and uses a fixed block size of 256 bytes.
* doc/avrdude.texi: Document support for mib510.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@773 81a1dc3b-b13d-400b-aceb-764788c761c2
"classic" AVRs (AT90, ATtiny, ATmega) in both,
ISP and high-voltage programming modes.
* Makefile.am: Add -lm.
* avrdude.conf.in: Add stk600, stk600pp, and stk600hvsp.
* config_gram.y: Add support for the stk600* keywords.
* lexer.l: (Ditto.)
* pgm.h: Add the "chan" parameter to set_varef().
* stk500.c: (Ditto.)
* serial.h: Add USB endpoint support to struct filedescriptor.
* stk500v2.c: Implement the meat of the STK600 support.
* stk500v2.h: Add new prototypes for stk600*() programmers.
* stk500v2_private.h: Add new constants used in the STK600.
* term.c: Add AREF channel support.
* usb_libusb.c: Automatically determine the correct write
endpoint ID, the STK600 uses 0x83 while all other tools use
0x82. Propagate the EP to use through struct filedescriptor.
* usbdevs.h: Add the STK600 USB product ID.
* tools/get-stk600-cards.xsl: XSL transformation for
targetboards.xml to obtain the list of socket and routing
card IDs, to be used in stk500v2.c (for displaying the
names).
* tools/get-stk600-devices.xsl: XSL transformation for
targetboards.xml to obtain the table of socket/routing cards
and their respective AVR device support for doc/avrdude.texi.
* avrdude.1: Document all the STK600 stuff.
* doc/avrdude.texi: Ditto. Added a new chapter for
Programmer Specific Information.
Thanks to Eirik Rasmussen from Atmel Norway for his support in
getting this code running within that short amount of time!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@768 81a1dc3b-b13d-400b-aceb-764788c761c2
the programmer backend.
jtagmkII.c: Implement the extended parameter jtagchain=
to support JTAG daisy-chains.
avrdude.1, doc/avrdude.texi: Document all of the above.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@761 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6121: ISP support for the C2N232I device (serial port
bitbanging)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@755 81a1dc3b-b13d-400b-aceb-764788c761c2
and link main.c against that library.
Add AC_PROG_RANLIB to configure.ac as we are building a library now.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@723 81a1dc3b-b13d-400b-aceb-764788c761c2
and EEPROM, based on the current Atmel XML file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@720 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (frank-stk200): Fix syntax error.
* ser_avrdoper.c: Make #ifdef for Win32/libhid
consistent with the initial check: use the HID driver
only iff found, otherwise use libusb.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@712 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #5507: Support for AVR-Doper USB programmer in HID mode
* configure.ac: Add hooks to detect the Win32 HID library,
as well as the existence of <ddk/hidsdi.h>.
* Makefile.am: Add new files.
* my_ddk_hidsdi.h: (New file.)
* ser_avrdoper.c: (New file.)
* serial.h: Add declaration for avrdoper_serdev.
* stk500v2.c: Add hook to divert to the AVR Doper code.
* avrdude.1: Document the AVR Doper support.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@704 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch
Hannes Weisbach
Rene Liebscher
Nils Springob
David Hoerl
Michal Ludvig