Commit Graph
8 Commits
Author SHA1 Message Date
jimmyandClaude Opus 5.5 2586ead4fa Put the chase speed on knob 1 in the test show.
A Speed dial on knob 1 (CC 30) sets the step time of the cans' and movers'
chase and zigzag runs, from 800 ms fully left to 50 ms fully right, starting
at the old 200 ms. Zigzag forward stays at half the step, and the dimmer holds
follow at 8 steps so they stretch with the run. The 500 ms trail is unchanged.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-23 00:02:08 +13:00
jimmyandClaude Opus 5.5 fc8abf9c99 Set the movers' zeros and pan directions, swap M1/M2's patch, and model tilt in the simulator.
The front right mover is on DMX 1 and the front left on 45, so M1 and M2
swap addresses in the stage map and test.qxw. Measured on the rig, pan 0
faces forward on the front pair and into the middle on the back pair, back
at 85. M1 and M4 turn anticlockwise, so movers get a pan_reverse flag.

Tilt 127 now points straight down: the simulator draws a spot under the
head, and past 127 the beam flips behind the pan heading.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-22 22:54:14 +13:00
jimmyandClaude Opus 5.5 2b0f9e2f9b Re-arrange the test show's console and put the movers' brightness with their position knobs.
The Dimmers sliders are now Middle, Front and Back, and the movers' Brightness
(knob 15) leads the Movers position frame.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-22 20:47:22 +13:00
jimmyandClaude Opus 5.5 86d87bf8cf Add a movers bank and Pan, Tilt, Focus and Rotate knobs to the test show.
Pause toggles bank 1 between the cans and the movers (scripts/shows/mover_bank.py).
Knobs 9-12 (CC 38-41) drive all four movers' pan, tilt, focus and lens
rotate, as in templeoftechno.qxw (scripts/shows/mover_position.py).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-22 19:56:38 +13:00
jimmyandClaude Opus 5.5 d522b1a2cf Add sound-reactive cans, a strobe pad and side chases to the test show.
The Sound pad (bank 1 note 36) toggles a QLC+ Audio Triggers widget whose
volume bar drives a Sound submaster beside the can dimmers, so the cans'
brightness follows the music while the movers stay steady. padcontroller sends
CC 100 at full on every press and release of that pad, bypassing its CC
smoothing, so switching sound off always leaves the cans at full.

test.qxw also gains Chase forward/reverse, a double and an opposing zigzag
down the side cans (RGB matrices whose colour follows the Colour 2 pads), a
Strobe flash pad with the cans' strobe channel forced HTP, and the Dimmers
frame, forced-LTP side colours and dimmer-free colour scenes from parallel
sessions.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-22 17:03:27 +13:00
jimmyandClaude Opus 5.5 643f7c8fb6 Send the test show's Art-Net to 127.0.0.1 for the simulator.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-22 14:34:05 +13:00
jimmyandClaude Opus 5.5 9742121144 Rename padeditor to padcontroller, with the MIDI intercept as padcontroller.midi and its virtual port as padcontroller.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-22 13:25:06 +13:00
jimmyandClaude Sonnet 5.5 6c060720ee Add two sets of colour scenes to the test show and light the pads from them.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-22 11:44:19 +13:00