Files
led-controller/main/Kconfig.projbuild
T
jimmyandClaude Opus 5.5 9d628aa3c8 fix: run the W5500 SPI bus at 10 MHz
At 20 MHz the controller intermittently dropped every Ethernet frame
over about 900 bytes, while small packets got through. The web UI then
hung after the first chunk of a response. At 10 MHz, full-size pings
and repeated fetches of every UI file all succeed.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-03 00:50:46 +13:00

140 lines
3.4 KiB
Plaintext

menu "W5500 config"
config W5500_SPI_HOST
int "SPI host number (1=SPI2, 2=SPI3)"
range 1 2
default 1
config W5500_SPI_CLOCK_MHZ
int "SPI clock speed (MHz)"
range 5 80
default 10
config W5500_SCLK_GPIO
int "SCLK GPIO (XIAO D8)"
default 7
config W5500_MISO_GPIO
int "MISO GPIO (XIAO D9)"
default 8
config W5500_MOSI_GPIO
int "MOSI GPIO (XIAO D10)"
default 9
config W5500_CS_GPIO
int "CS GPIO (XIAO D1)"
default 2
config W5500_INT_GPIO
int "INT GPIO (XIAO D2), -1 to poll"
default 3
config W5500_POLL_PERIOD_MS
int "RX poll period (ms) when INT is -1"
default 10
config W5500_RST_GPIO
int "RST GPIO (XIAO D0), -1 if not wired"
default 1
endmenu
menu "INMP441 mic config"
config MIC_SCK_GPIO
int "SCK GPIO (XIAO D4)"
default 5
config MIC_WS_GPIO
int "WS GPIO (XIAO D5)"
default 6
config MIC_SD_GPIO
int "SD GPIO (XIAO D6)"
default 43
config MIC_STREAM_GAIN
int "Digital gain for the audio stream (x)"
range 1 256
default 16
help
The INMP441 is quiet at full scale; x16 (+24 dB) makes speech
audible without clipping at normal distances.
endmenu
menu "Beat detection config"
config BEAT_LED_GPIO
int "Beat LED GPIO (XIAO user LED is 21), -1 for none"
default 21
config BEAT_LED_ACTIVE_LOW
bool "Beat LED lights when the pin is low"
default y
config BEAT_LED_PULSE_MS
int "Beat LED flash length (ms)"
range 10 500
default 60
config BEAT_LED_DOWNBEAT_MS
int "Beat LED flash length on the first beat of a bar (ms)"
range 10 1000
default 200
config BEAT_GATE_DBFS
int "Ignore audio quieter than this (dBFS, before stream gain)"
range -100 -20
default -75
help
The INMP441 self-noise is about -87 dBFS. Background music in a
room can sit around -65 dBFS, so keep this well below that.
config BEAT_LEAD_MS
int "Fire predicted beats this early (ms)"
range 0 200
default 30
help
Beats are predicted from the tempo, so they can be sent early
to cancel the ~30 ms of capture and analysis latency. Raise it
to cover output latency too (e.g. network or lights).
endmenu
menu "ESP-NOW config"
config ESPNOW_CHANNEL
int "Wi-Fi channel shared with the LED drivers"
range 1 13
default 6
config BEAT_TX_COPIES
int "Copies sent of every beat frame"
range 1 4
default 2
help
Each beat is broadcast this many times with the same beat index.
Drivers act on the first copy that arrives and drop the rest.
config BEAT_TX_GAP_US
int "Gap between beat copies (us)"
range 500 10000
default 2000
config BEAT_TEST_GPIO
int "GPIO toggled on every beat sent (-1 = off)"
range -1 48
default -1
help
For latency measurement: a logic analyzer or scope on this pin and on
the driver's beat pin shows the true master-to-LED delay.
config BULK_HOLDOFF_US
int "Hold bulk traffic back after a beat (us)"
range 0 20000
default 3000
endmenu