Move project to repo root and add Makefile
The Makefile wraps the build, USB and WiFi flashing, the serial monitor and font generation, with toolchain paths that can be overridden. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
3b4154d8bf
commit
9f84330b91
17 files changed
+53
-9
No files matched your search
File renamed without changes.
@@ -0,0 +1,44 @@
|
||||
# Build and flash the firmware. Override any of these on the command line,
|
||||
# e.g. make ota BOARD=192.168.1.50
|
||||
IDF_PATH ?= $(HOME)/esp/esp-idf
|
||||
TOOLCHAIN ?= $(HOME)/.arduino15/packages/esp32/tools/esp-x32/2507/bin
|
||||
PYENV ?= $(HOME)/.espressif/python_env/idf5.4_py3.12_env
|
||||
PORT ?= /dev/ttyACM0
|
||||
BOARD ?= 10.1.1.167
|
||||
|
||||
# IDF_MAINTAINER skips IDF's tool version check, as the toolchain above is
|
||||
# the Arduino core's rather than the one IDF installs
|
||||
export IDF_PATH
|
||||
export IDF_MAINTAINER := 1
|
||||
export PATH := $(TOOLCHAIN):$(PYENV)/bin:$(PATH)
|
||||
|
||||
PYTHON := $(PYENV)/bin/python
|
||||
BIN := build/vga_test.bin
|
||||
|
||||
.PHONY: all build flash ota monitor font clean
|
||||
|
||||
all: build
|
||||
|
||||
build/build.ninja:
|
||||
cmake -S . -B build -G Ninja -DPYTHON=$(PYTHON) -DPYTHON_DEPS_CHECKED=1 -DIDF_TARGET=esp32s3
|
||||
|
||||
build: build/build.ninja
|
||||
ninja -C build
|
||||
|
||||
# Over USB
|
||||
flash: build
|
||||
cd build && $(PYTHON) -m esptool --chip esp32s3 -p $(PORT) -b 460800 --before default_reset --after hard_reset write_flash @flash_args
|
||||
|
||||
# Over WiFi
|
||||
ota: build
|
||||
curl -X POST --data-binary @$(BIN) http://$(BOARD)/api/ota
|
||||
|
||||
monitor:
|
||||
$(PYTHON) $(IDF_PATH)/tools/idf_monitor.py -p $(PORT) build/vga_test.elf
|
||||
|
||||
# Needs Pillow and the DejaVu fonts
|
||||
font:
|
||||
python3 tools/gen_font.py main/font_data.h
|
||||
|
||||
clean:
|
||||
rm -rf build
|
||||
@@ -29,12 +29,16 @@ Ground goes to VGA pin 5 and pins 6–8, and VGA pin 9
|
||||
|
||||
## Build and flash
|
||||
|
||||
You need ESP-IDF 5.4 or later.
|
||||
You need ESP-IDF 5.4 or later. The paths at the top of the `Makefile` point
|
||||
at the toolchain to use; override them if yours are elsewhere.
|
||||
|
||||
```
|
||||
cd vga_test
|
||||
idf.py set-target esp32s3
|
||||
idf.py build flash
|
||||
make # build
|
||||
make flash # flash over USB (PORT=/dev/ttyACM0)
|
||||
make ota # flash over WiFi (BOARD=<board-ip>)
|
||||
make monitor # serial console
|
||||
make font # regenerate main/font_data.h
|
||||
make clean
|
||||
```
|
||||
|
||||
The serial console is on the USB-Serial-JTAG port, because GPIO 43/44 carry
|
||||
@@ -46,8 +50,4 @@ The board starts its own access point, `ESP32-VGA` (password `esp32vga`).
|
||||
You can also give it your home WiFi details in Settings. Open its IP address
|
||||
in a browser.
|
||||
|
||||
To update the firmware over WiFi, use the page's Settings section, or run:
|
||||
|
||||
```
|
||||
curl -X POST --data-binary @build/vga_test.bin http://<board-ip>/api/ota
|
||||
```
|
||||
To update the firmware over WiFi, use the page's Settings section or `make ota`.
|
||||
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
File renamed without changes.
|
500 Internal Server Error
An error occurred: An error occurred Gitea Version: 28.2.0 |