First Release

custom/net-tweaks/00-patches/00-cmdline.txt.diff

@@ -0,0 +1,6 @@
+--- a/rootfs/boot/cmdline.txt	2019-07-25 08:58:33.178998588 +1200
++++ b/rootfs/boot/cmdline.txt	2019-07-27 21:48:44.709707517 +1200
+@@ -1 +1 @@
+-console=serial0,115200 console=tty1 root=ROOTDEV rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet init=/usr/lib/raspi-config/init_resize.sh
++console=serial0,115200 console=tty1 root=ROOTDEV rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait modules-load=dwc2,g_ether quiet init=/usr/lib/raspi-config/init_resize.sh
+

custom/net-tweaks/00-patches/01-config.txt.diff

@@ -0,0 +1,19 @@
+--- /rootfs/boot/config.txt	
++++ /rootfs/boot/config.txt	
+
+@@ -56,6 +56,14 @@
+ # Enable audio (loads snd_bcm2835)
+ dtparam=audio=on
+ 
++#usb ethernet
++[pi0]
++dtoverlay=dwc2
++
++#usb ethernet
++[pi3]
++dtoverlay=dwc2,dr_mode=peripheral
++
+ [pi4]
+ # Enable DRM VC4 V3D driver on top of the dispmanx display stack
+ dtoverlay=vc4-fkms-v3d
+

custom/net-tweaks/00-patches/config.txt

@@ -0,0 +1,73 @@
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2c_arm=on
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+#usb ethernet
+[pi0]
+dtoverlay=dwc2
+
+#usb ethernet
+[pi3]
+dtoverlay=dwc2,dr_mode=peripheral
+
+[pi4]
+# Enable DRM VC4 V3D driver on top of the dispmanx display stack
+dtoverlay=vc4-fkms-v3d
+max_framebuffers=2
+
+[all]
+#dtoverlay=vc4-fkms-v3d

custom/net-tweaks/00-patches/series

@@ -0,0 +1,2 @@
+00-cmdline.txt.diff
+01-config.txt.diff