In this function the NVM enable bit in TPISR is written to zero, like
described in AVR918. The reset line is released in avrftdi_close().
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1149 81a1dc3b-b13d-400b-aceb-764788c761c2
Device identification is possible tested under OS X 10.6.8 with an
FT4232H and ATtiny10.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1145 81a1dc3b-b13d-400b-aceb-764788c761c2
ERROR is already defined as a preprocessor macro in wingdi.h.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1144 81a1dc3b-b13d-400b-aceb-764788c761c2
Messages are divided by severity and printed accordingly to verbosity, as
specified by the user. The provided severity level are (ERROR, WARN, INFO,
DEBUG, TRACE). Where "ERROR" messages are always printed. Shortcut-macros
including function, from which the output was generated, and line number were
also added. Some log messages were updated and other code warnings removed.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1143 81a1dc3b-b13d-400b-aceb-764788c761c2
Apparently, doing too large read/write I/O on the MPSSE fills up the RX Buffer
of the chip, resulting in STALL/NAK of additional transactions of an OUT request.
Since the OUT request is issued synchronously, an appropriate IN request cannot
be issued, resulting in a deadlock.
This problem is handled by submitting small enough OUT requests, that will not
fill up the RX buffer and interleaving them with IN requests.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1142 81a1dc3b-b13d-400b-aceb-764788c761c2
This includes adding libftdi1 to configure.ac and Makefile.am.
avrftdi code is changed to use libftdi1. At the same time device
discovery is moved to libftdi1. Some error and debug messages in
avrftdi are corrected and/or updated. avrftdi_print is updated,
to print all messages whose verbosity level is less or equal to
the global verbosity level, so that messages with level 0 are always
printed.
This change is tested on OS X 10.6.8, Ubuntu 12.04.2 and Win7 x86_64.
The Win7 version was cross-compiled on OS X 10.6.8.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1141 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: added usbpid, usbvid to usbtiny
* usbtiny.[ch]: use usbpid, usbpid if provided in config file
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1134 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (avrftdi): fix comments about ACBUS vs. ADBUS;
add a comment that the MPSSE signals are fixed by the FTDI
hardware and cannot be changed
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1133 81a1dc3b-b13d-400b-aceb-764788c761c2
the main data endpoints when being forced so by the USB; this can
happen when attaching the JTAGICE3 to a USB 1.1 connection
* jtag3.c (jtag3_initialize): When detecting a downgraded max
transfer size on the JTAGICE3 (presumably, due to being connected
to USB 1.1 only), bail out as its firmware cannot properly handle
this (by now)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1129 81a1dc3b-b13d-400b-aceb-764788c761c2
(USBDEV_BULK_EP_READ_STK600): new define values
* stk500v2.c (stk600_open): use the STK600 EP values,
as they are different from AVRISPmkII
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1126 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtagmkII.c (jtagmkII_initialize): For Xmega devices, and
firmware >= 7.x, don't trigger a RESET, in order to work around a
firmware bug that appears to be present in at least firmware 7.24
for the Dragon.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1125 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrpart.c: (Dito)
* avrpart.h: (Dito)
* lexer.l: (Dito)
* avrdude.conf.in: Add "ocdrev" key/value pairs, based
on the AS6 XML file information.
* jtag3.c: Use the ocdrev in the parameter block.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1124 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtag3.h: (Dito.)
* jtag3_private.h: Add two new commands
* stk500v2.c: Implement the "MonCon disable" hack that
allows temporarily falling back to ISP when trying to
talk to a part that has debugWIRE enabled
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1123 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Add "jtag3isp" programmer
* jtag3.c: jtag3_setparm() is now public
* jtag3.h: (Dito)
* stk500v2_private.h: Command 0x1D is CMD_SPI_MULTI only
for STK500v2, AVRISPmkII, and JTAGICEmkII; for JTAGICE3,
it's CMD_SET_SCK now; also add CMD_GET_SCK
* avrpart.c (avr_get_output_index): New function
* avrpart.h: (Dito)
* stk500v2.c: Implement the pasthrough programmer glue logic
for JTAGICE3 in ISP mode
* stk500v2.h: (Dito)
* avrdude.1: Document the JTAGICE3 support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1119 81a1dc3b-b13d-400b-aceb-764788c761c2
m->offset from addr, JTAGICE3 doesn't need it anymore (similar
to JTAGICEmkII with 7+ firmware)
* jtag3.c (jtag3_read_byte): Allow for full-page reads of
EEPROM also for Xmega and debugWIRE, allow for signature
read in debugWIRE
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1117 81a1dc3b-b13d-400b-aceb-764788c761c2
across during development
* jtag3.c: (Dito.)
* usb_libusb.c: Reduce timeouts from 100 to 10 s, still long
enough, but not getting cold feet when something goes wrong.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1116 81a1dc3b-b13d-400b-aceb-764788c761c2
* usbdevs.h: Add defines that mark an event in return
from usb_recv_frame().
* usb_libusb.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1115 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Fix page sizes for all Xmega devices,
by cross-checking against Atmel Studio's device XML files
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1112 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI and JTAG).
* jtagmkII.c (jtagmkII_set_xmega_params): Use "fuse1" rather
than "fuse0" memory space to fill in the NVM offset from, as
there is no "fuse0" on some Xmega devices.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1111 81a1dc3b-b13d-400b-aceb-764788c761c2
traces made by Knut Schwichtenberg, and by similarity to
JTAGICEmkII.
Still quite incomplete, just megaAVR/JTAG is done by now.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1109 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #37727 Add support for LM3S811 dev board as a programmer
* lexer.l,config_gram.y: accepting inverted pins at pin lists
syntax: ~num or ~(num,num,...)
* par.c: par_set_many_bits is now usable with inverted pins
* avrftdi.c: fixed wrong index in ftdi_pin_name
* avrdude.conf.in: added programmer lm3s811
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1106 81a1dc3b-b13d-400b-aceb-764788c761c2
No signs are allowed as negative values do not make sense for current config values.
* buspirate.c: include own header file buspirate.h
* doc/.cvsignore: add programmers.texi to ignore list
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1105 81a1dc3b-b13d-400b-aceb-764788c761c2
$(builddir) for generated files, so "make distcheck"
works again.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1104 81a1dc3b-b13d-400b-aceb-764788c761c2
* ft245r.c: added semaphore workaround for MacOS X,
added pthread_testcancel in reader thread
* configure.ac: added check for TYPE_232H in libftdi (not in libftdi < 0.20)
* avrftdi.c: do not use TYPE_232H if not declared
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1101 81a1dc3b-b13d-400b-aceb-764788c761c2
hweisbach
joerg_wunsch
rliebscher