The very basic functionality (paged flash read/write, erase, terminal
mode reads, fuse writes) works fine. There are still the following
issues right now:
. paged EEPROM write (i.e. through -U eeprom:w:...) only works on an
erased EEPROM
. byte-access flash and EEPROM writes (i.e. in terminal mode) fail
. documentation needs to be updated still
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@547 81a1dc3b-b13d-400b-aceb-764788c761c2
-added support for ATMega168, patch #4532 thanks to Manfred Bartz
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@544 81a1dc3b-b13d-400b-aceb-764788c761c2
While Solaris' lex understands start conditions, they cannot be grouped,
so unfold the <strng> group.
All actions need braces, even if they only consist of a comment.
As the classic lex uses semi-static resource allocation, we need to bump
the resource limits quite a bit.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@541 81a1dc3b-b13d-400b-aceb-764788c761c2
two-step declaration, and first define token_p to be a token_t *,
and then define YYSTYPE to token_p. That works around a bug in
Solaris' yacc.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@540 81a1dc3b-b13d-400b-aceb-764788c761c2
* Makefile.am: distclean avrdude.conf.
* avrdude.conf.in: make the parallel-port programmers optional.
* bitbang.c: move the bitbang features out into PROGRAMMER.
* configure.ac: introduce --enable-parport, add Solaris.
* lexer.l: replace str by strng to work around problems in some
versions of flex.
* main.c: move getexitspecs into the respective programmer's
domain; replace rindex by the C-standard strrchr.
* par.c: make parallel port optional.
* par.h: everything but par_initpgm() is private now.
* pgm.h: add setping/getping/highpulsepin/getexitspecs.
* serbb_posix.c: generalize bitbang interface; replace
cfmakeraw() by explicit code.
* serbb_win32.c: generalize bitbang interface.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@539 81a1dc3b-b13d-400b-aceb-764788c761c2
wide tty output. Document a trick to find out about the serial
numbers of all JTAG ICEs attached to USB.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@534 81a1dc3b-b13d-400b-aceb-764788c761c2
. use the correct endpoint, depending on whether we are going to read
or write
. when opening the USB device, set the configuration according to the
config entry, and properly claim the interface
. when closing, release the interface again
With these changes, it works now with libusb-win32 as well.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@533 81a1dc3b-b13d-400b-aceb-764788c761c2
so the buffer will then be allocated correctly.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@532 81a1dc3b-b13d-400b-aceb-764788c761c2
give the full name of the respective memory area, instead of
the (possibly abbreviated) name the user typed in the -U option.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@529 81a1dc3b-b13d-400b-aceb-764788c761c2
string. Actually evaluate that number as microseconds then, as the
documentation used to state already.
While being there, re-sort the -s option into alphabetical order.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@527 81a1dc3b-b13d-400b-aceb-764788c761c2
Document the addition of the latest safemode update in the change log.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@522 81a1dc3b-b13d-400b-aceb-764788c761c2
* add support for parts with just 'fuse' memory
* if any fuse memories are altered, reflect those changes in the
post-programming safemode check so that safemode no longer
complains about fuses which were intentionally altered; this
eliminates the need to completely disable safemode using -u in
order to program fuses.
* provide -s option which will not ask to restore fuses, it will
just do it
Submitted by: Colin O'Flynn <coflynn@newae.com>
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@519 81a1dc3b-b13d-400b-aceb-764788c761c2
will be available in the upcoming avrdude release.
His addition has been implemented by means of a generalized bit-bang
interface that contains the common part between serial and paralle
bit-bang devices, and specialed backends for the serial and parallel
port connections.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@515 81a1dc3b-b13d-400b-aceb-764788c761c2
was the whole programmer submission which was already added through
another request, but the former lacked the VCC definition. Pick it up
from this patch.
Submitted by: tmohr@s.netic.de
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@511 81a1dc3b-b13d-400b-aceb-764788c761c2
avr910 programmer.
Original Submission: The attached patch against avrdude 4.4.0 fixes
the following problems with paged writes in avr910.c:
- failure to re-set address after page writes;
- no polling or delay after page writes;
- no page writes when not using auto-increment;
- an extraneous page write when data ends on page boundary.
Submitted by: "Nic" <avrdude@schraudolph.org>
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@510 81a1dc3b-b13d-400b-aceb-764788c761c2
match the XML file.
This fixes
bug #7492: EEPROM writing fail on atmega103 with atavrisp
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@509 81a1dc3b-b13d-400b-aceb-764788c761c2
Do not rebuild the docs again if they are up-to-date. This avoids as
well that they are rebuilt during "make install".
Use mv -f instead of plain mv in order to install the docs into the
respective subdirs, in order to avoid silly questions for non-writable
destination files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@508 81a1dc3b-b13d-400b-aceb-764788c761c2
one.
This closes
bug #11496: Memory bank calibration on atmega128 should have 4 bytes
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@506 81a1dc3b-b13d-400b-aceb-764788c761c2
This fixes EEPROM access using the STK500V2 programmer, partially
undoing part of a previous general fixup commit. Choose the correct
read/write operations with the stk500v2 program function - the correct
one depends on the memory type. EEPROM is byte addressable so uses
read/write. FLASH is word addressable and so uses read_lo/write_lo.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@501 81a1dc3b-b13d-400b-aceb-764788c761c2
doc/avrdude.texi: (Ditto.)
Closes bug #13501: <memtype> should be listed in the man page
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@500 81a1dc3b-b13d-400b-aceb-764788c761c2
gratitous API change in recent versions of texi2html where
the output directory has changed names.
Fix for:
bug #13026: The build fails with texi2html 1.76
bug #12715: make issues during install
patch #3091: commandline fix for latest version of texi2html
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@499 81a1dc3b-b13d-400b-aceb-764788c761c2
Colin O Flynn
Joerg Wunsch
Brian S. Dean