avrdude/NEWS

1056 lines
36 KiB
Plaintext
Raw Normal View History

$Id$
Approximate change log for AVRDUDE by version.
(For detailed changes, see the version control system logs.)
----------------------------------------------------------------------
Changes since version 6.4:
* Major changes compared to the previous version:
* New devices supported:
* New programmers supported:
* Bugfixes:
* Patches:
* Internals:
Version 6.4:
* Major changes compared to the previous version:
- libhidapi support (part of patch #8717)
- use libhidapi as (optional) transport for CMSIS-DAP compliant
debuggers (JTAGICE3 with firmware 3+, AtmelICE, EDBG, mEDBG)
- UPDI support added (AVR8X family)
- TPI support for USBtinyISP
- TPI support for ft245r
- TPI support for linuxgpio
- AVR Doper uses libhidapi rather than raw libusb (patch #9033)
- -P net:host:port can use IPv6 now (Posix systems only)
- New configure option: -disable-libusb_1_0
- extended UPDI device context (> 64 Ki flash)
- major overhaul of ft245r driver (patch #9327/#9328)
- some improvements in linuxspi driver
- Use -B <bitclock> rather than -b <baudrate> for linuxspi driver
- unused lock byte bits are not masked on read anymore
- parport support disabled by default; configure with
--enable-parport to explicitly enable it
* New devices supported:
- ATmega328PB
- AVR8X family, ATtiny1617, ATtiny817, ATtiny202, ATtiny204,
ATtiny402, ATtiny404, ATtiny406, ATtiny804, ATtiny806,
ATtiny807, ATtiny1604, ATtiny1606, ATtiny1607, ATtiny212,
ATtiny214, ATtiny412, ATTiny414, ATtiny416, ATtiny417,
ATtiny814, ATtiny816, ATtiny1614, ATtiny1616, ATtiny3214,
ATtiny3216, ATtiny3217, ATmega3208, ATmega3209, ATmega4808,
ATmega4809
- ATtiny841, ATtiny441
- ATmega64M1
- ATmega324A
- ATmega808, ATmega809, ATmega1608, ATmega1609, AVR DA, AVR DB
- LGT8FX88P, LGT8FX168P, LGT8FX328P
- ATmega324PB
- ATmega8A
* New programmers supported:
- ehajo-isp (commercial version of USBtiny)
- XplainedPro in UPDI mode
- XplainedMini in UPDI mode
- JTAGICE3 in UPDI mode
- Atmel Powerdebugger in all modes (JTAG, PDI, UPDI, debugWIRE, ISP)
- linuxspi (direct SPI bus e.g. on Raspberry Pi devices)
- PICkit4, Snap, PKoB
- iseavrprog
- XBeeBoot
* Bugfixes:
bug #47550: Linux GPIO broken
bug #47718: "lfuse reads as" not displayed in verbose mode - SOLUTION
bug #48084: Avoid compiled-in timestamp for reproducible release builds
bug #47376: ATtiny841 description missing in configuration file
bug #49455: support for tiny441
bug #57428: document when 'arduino' or 'wiring' should be used, and -D requirement of latter
bug #58095: error setting efuse on atmega328pb variant
bug #51409: Can't program EFUSE on ATmega32M1
bug #60753: Patch #1436 breaks multiple programmer/device combinations on MacOS BigSur
bug #59525: Bogus error message because Copy/Paste typo in stk500.c
bug #58078: [PATCH] buspirate: remove compound literals (fixes GCC>=9)
bug #57453: [PATCH] fix reference to nonexistant -m option by changing to -U
bug #59227: Add new part. How does one get a part added to the CONF file?
bug #55009: no efuses for m164a/pa
bug #55734: USBtiny programming of ATmega328p broken by Patch #9278
bug #58495: Add atmega324pb support to avrdude.conf.in
bug #60863: avrftdi programming error probably caused by multiple, consecutive empty pages
bug #50517: Reading fails if "immediate mode" for output file format is selected - fileio: invalid operation=1
bug #50630: Erase Cycle Counter options ( -y -Y n ) should be removed from usage Message
bug #48767: ser_drain() for TCP on Windows doesn't work
bug #46759: avrdude 6.1 -> 6.2 regression: lock byte verification error
bug #58440: linuxgpio PIN limit too low
bug #55462: wrong programmer id check in jtag3_getsync() and jtag3_close()
bug #58994: VPP PWM still enabled at the end of programming process
bug #57338: if safemode has to change fuses avrdude should exit with non-zero exit code
bug #60575: Permission denied on macOS Big Sur
* Patches:
patch #9482: Add support for UPDI and AVR8X
patch #9508: Add PowerDebugger and XPlained Mini in UPDI mode
patch #9507: Fix UPDI chip erase
patch #9506: Script to create device configuration stub from Atmel
ATDF files
patch #9423: Support ATtiny841 and ATtiny441
patch #9530: Update URL to Ladyada's USBtinyISP page.
patch #9317: Support atmega64m1 as part
patch #9222: Enable silent build
patch #8924: Enable TPI for usbtiny
patch #9033: avrdoper backend uses libhidapi instead of libusb
patch #8580: FT245r support to select device by serial number
patch #8910: ATxmega32c4 and ATxmega16c4 have wrong signatures
patch #8219: Fix boot_start for xmega devices on jtagmkII
patch #9185: Add extended_param to usbasp.c - erasing
patch #8311: Add IPv6 support to the -Pnet:host:port option
patch #9542: Correct "usersig" on avr8x devices
patch #8128: Added new option to configure.ac script
patch #8444: Proposal for modifications in -B and -U command options managment (partially)
patch #9735: spelling error fix: psuedo -> pseudo
patch #9893: [PATCH] Reader reads ftdi handle after main thread close it
patch #9819: Address several leaks in SVN rev 1429
patch #9820: Fix some out-of-bounds/uninitialized issues
patch #9818: correct typos in SVN rev 1429
patch #9732: usbtiny_paged_load overflows buffer e.g. when reading EEPROM
patch #9966: Add JTAGICE3 in UPDI mode
patch #9963: UsbAsp 3 MHz patch for UsbAsp-flash firmware
patch #9816: Implement new programmer type: linuxspi
patch #9811: ATmega328pb has efuse bit 3
patch #9744: Patch for ATMega324A support
patch #10000: Add support for extended UPDI device context
patch #9697: Add iseavrprog support
patch #10017: uspasp / tpi: Automatically clear configuration byte (fuse) before writing it
patch #8957: Allow reading prodsig memory from stk500v2 on xmega devices
patch #9110: Let reserved fuse bits to be read as *don't care*
patch #9253: Fix for giving terminal_mode commands more than 20 arguments
patch #9320: fix TPI RESET in bitbang.c
patch #9079: Fix ftdi_syncbb teardown (supersedes #9893, superseded by #9328)
patch #9122: Fixed MISO sampling in ftdi_syncbb
patch #9123: ftdi_syncbb: use FT245R_CYCLES in ft245r_set_bitclock()
patch #8719: Support Over-the-Air bootloading with XBeeBoot
patch #9757: Fix ATtiny817 Xplained Mini programmer
patch #9327: ft245r.c: add TPI support (patches 1-4)
patch #9328: ft245r.c: add TPI support (patches 5-7)
patch #10027: linuxspi: Add reset pulse, according to AVR programming algorithm
patch #10028: linuxspi: close() only when necessary
patch #10029: linuxspi: Report GPIO_GET_LINEHANDLE_IOCTL errors
patch #10030: linuxspi: Support inverted GPIO pin
patch #10031: linuxspi: Support GPIO uAPI v2
(no-id): Improve documentation of linuxspi driver, provide portname default
(no-id): Use -B <bitclock> rather than -b <baudrate> for linuxspi driver
patch #9304: [Bug #48767] Implemented WinSock variation of "ser_drain(...)" functionality
patch #8996: Remove lock byte read mask (bug#21954, bug#46759)
patch #8923: Enable TPI for linuxgpio
patch #10153: linuxspi: Support "-E reset" and "-E noreset"
* Internals:
- New avrdude.conf keyword "family_id", used to verify SIB attributes
on AVR8X architecture if device is locked.
Version 6.3:
* Major changes compared to the previous version:
- Backout of
patch #8380: adds 500k 1M 2M baud to ser_posix.c
It broke the functionality in too many situations
(bug #46610/46483)
* New devices supported:
- ATmega48PB, ATmega88PB, ATmega168PB
- ATtiny28 (HVPP-only device)
* New programmers supported:
- Atmel mEDBG: xplainedmini, xplainedmini_dw
* Bugfixes
- bug #46610: Floating point exception (core dumped) arch linux rpi2
- bug #46483: version 6.2. ser_open(): can't set attributes for device
- patch #8435: Implementing mEDBG CMSIS-DAP protocol
- patch #8735: ATtiny28 support in avrdude.conf
- patch #8896: Silence cppcheck warnings in 6.2 code
- patch #8895: Spelling in 6.2 code
Version 6.2:
* Major changes compared to the previous version:
- The stk500v2 implementation now uses its own higher-level
command implementation for byte-wide access, rather than the
historic SPI_MULTI command where all the low-level ISP
implementation had to be assembled manually inside AVRDUDE. In
addition to the traditional STK500, this implementation is also
used by all the more modern Atmel tools (AVRISPmkII, JTAGICEmkII
in ISP mode, STK600 in ISP mode).
- The -B option can be suffixed with "Hz", "kHz", or "MHz", in
order to specify a bitclock frequency rather than period.
- Print part id after signature (patch #8440 )
- buspirate: Also support "cpufreq" extended parameter
in binary mode (patch #8504 )
- The "-P net:" syntax (forwarding of serial data over TCP) is now
also implemented for Win32 systems.
- Allow for arbitrary serial baudrates under Linux (OSX and *BSD
could already handle it).
* New devices supported:
- AT90PWM216 (bug #42310: New part description for AT90PWM216)
- ATmega32M1 (patch #7694 Add support for the atmega32m1)
* New programmers supported:
- ftdi_syncbb
+ uncompatino, ttl232r (FTDI TTL232R-5V with ICSP adapter)
(patch #8529 2 more ftdi_syncbb devices)
* Bugfixes
- bug #45727: Wrong atmega8u2 flash parameters
- bug #46020: Add TIAO TUMPA to the conf file.
- bug #46021: Please add read in the memory lock section of ATtiny85
- bug #42337 avrdude.conf updates for UM232H/CM232H
- bug #42056: double free or corruption triggered at exit
- bug #42158: Linux GPIO - Source Typo
- bug #42516 spelling-error-in-binary
- patch #8419 fix ftdi_syncbb hang with libftdi 1
- bug #43002 usbasp debug output typo
- patch #8511 Fix reset on FT245R
- bug #40142 Floating point exception on Ubuntu 10.04
- bug #22248: Read efuse error (partial fix)
- bug #42267: jtag3isp fails to read lock and fuse bytes directly
after changing lock byte
- bug #41561: AVRDUDE 6.0.1/USBasp doesn't write first bytes of
flash page
- bug #43078: AVRDUDE crashes after sucessfully reading/writing eeprom
- bug #43137: Writing and reading incorrect pages when using jtagicemkI
- bug #40870: config nitpick: ATtiny25/45/85 have 1 calibration byte not 2
- bug #42908: no external reset at JTAGICE3
- patch #8437: [PATCH] Serial-over-ethernet for Win32
- bug #44717: avrdude creates empty flash dump
* Internals:
- Removing exit calls from config parser
- bug #42662 clang warnings under FreeBSD 10.x
Version 6.1:
* Major changes compared to the previous version:
- Atmel EDBG protocol support added (JTAGICE3, XplainedPro, Atmel-ICE)
* New programmers supported:
- Atmel DFU, using FLIP protocol version 1 (AT90USB and ATmega*U* devices),
or version 2 (Xmega devices)
- Atmel-ICE (ARM/AVR), JTAG, PDI, debugWIRE, ISP modi
* Bugfixes
- bug #40055: AVRDUDE segfaults when writing eeprom
- bug #40085: Typo fix in fuses report (for 6.1-svn-20130917)
- bug #40782: Verify errors for object size > 16 k on x32e5 due
to typo in avrdude.conf
- bug #40817: Elf file support (possibly) not working on 6.0.1 windows build
- bug #40897: AT Mega2560 not correctly programmed with stk500(v1)
ISP (solution patch)
- bug #41357: OS X: Avrdude messes with the usb stack?
- bug #41402: dfu.c missing include <stdint.h>
- patch #7896: DFU FLIPv2 programming support
- patch #XXXX: xxx
* Internals:
- (Some) programmers can take a list of USB PIDs now.
Version 6.0:
* Major changes compared to the previous version:
- Programmer types in configuration file are no longer keywords but
specified as string.
So you need to change 'type = XYZ;' to 'type = "XYZ";' in own
config files. (internal: The parser does not need to know all
programmer types now, new programmers will update only the table
in pgm_type.c.)
- The erase cycle counter (formerly options -y / -Y) has been
removed.
- Specifying a -U option without a memory type (short form of
option argument list) now defaults to "application" memory for
Xmega devices, and "flash" for everything else. This ensures
the Xmega bootloader is not accidentally touched.
- For programmers that support it, the default erase method is a
page erase now, rather than a chip erase (Xmega only).
- Keep track of input file contents
Memory segments are being tracked to remember whether they've
been actually read from a file. Only segments that came from a
file are being programmed into the device, or considered for
verification. This drastically improves handling speed for
sparse files (e.g. files that have a second bootloader segment),
and it ensures the device contents is actually compared for
everything mentioned in the file (even in case the file has
large 0xFF blocks).
- The -U option now accepts ELF files as input files, and extracts
the appropriate section contents that matches the requested memory
region. To enable this feature, the host system used for the
compilation must have a libelf around, including the respective
header files (i.e., package "libelf-devel" on many Linux systems).
- Programmers and parts lists
They are now sorted at output with '-c ?'/'-p ?'. (patch #7671:
Sorting programmers and parts lists for console output)
Programmers and parts lists in documentation generated from lists
mentioned above. (patch #7687: Autogenerating programmers and
parts lists for docs)
Output list of programmer types with '-c ?type', add list to
documentation
- Configuration files now accepts parent parts/programmers, parts
starting with '.' (eg. .xmega) are not included in output parts
list and can be used as abstract parents
(bug #34302: Feature request : device configuration with parent classes)
(patch #7688: Implement parent programmers feature)
- Additional config files which are read after default can be
specified on command line using '-C +filename'
(patch #7699 Read additional config files)
- "Safemode" can now be turned off by default from within a
configuration file (like ~/.avrduderc).
- The new option -l logfile allows to redirect diagnostic messages
to a logfile rather than stderr. Useful to record debugging
traces, in particular in environments which do not offer
shell-style redirection functionality for standard streams.
- When leaving debugWIRE mode, immediately retry with ISP rather
than bailing out completely.
- The USBasp programmer implementation now supports detailed traces
with -vvv, and device communication traces with -vvvv.
- The "verbose" terminal mode command allows to query or modify the
verbosity level.
* New devices supported:
- ATmega48P (patch #7629 add support for atmega48p)
- AT90PWM316 (bug #21797: AT90PWM316: New part description)
- ATxmega16D4, ATxmega32D4, ATxmega64D4, ATxmega128D4
- ATmega256RFR2, ATmega128RFR2, ATmega64RFR2, ATmega2564RFR2,
ATmega1284RFR2, ATmega644RFR2
- ATtiny1634
- ATxmega128A1U, ATxmega128A3U, ATxmega128A4U, ATxmega128B1,
ATxmega128B3, ATxmega128C3, ATxmega128D3, ATxmega16A4U,
ATxmega16C4, ATxmega192A3U, ATxmega192C3, ATxmega192D3,
ATxmega256A3BU, ATxmega256A3U, ATxmega256C3, ATxmega256D3,
ATxmega32A4U, ATxmega32C4, ATxmega384C3, ATxmega384D3,
ATxmega64A1U, ATxmega64A3U, ATxmega64A4U, ATxmega64B1,
ATxmega64B3, ATxmega64C3, ATxmega64D3
- ATtiny43U
- ATmega406
- ATxmega8E5, ATxmega16E5, ATxmega32E5
- ATtiny20, ATtiny40
* New programmers supported:
- linuxgpio
+ any (embedded) Linux system with 4 GPIOs available can be used
as a programmer with little or no additional hardware.
- avrftdi
+ o-link (patch #7672 adding support for O-Link (FTDI based
JTAG) as programmer)
+ 4232h (patch #7715 FT4232H support)
- TPI support
+ openmoko (bug #37977 Support for Openmoko Debug Board)
- usbasp
+ nibobee (previously specified as '-c usbasp -P nibobee)
+ usbasp-clone (same as usbasp but ignores vendor and product
string, checks only vid/pid)
- ftdi_syncbb (new type for synchronous bitbanging with ft232r/ft245r)
+ ft245r (FT245R Synchronous BitBang, miso = D1, sck = D0, mosi
= D2, reset = D4)
+ ft232r (FT232R Synchronous BitBang, miso = RxD, sck = RTS,
mosi = TxD, reset = DTR)
+ bwmega (BitWizard ftdi_atmega builtin programmer, miso = DSR,
sck = DCD, mosi = CTS, reset = RI)
+ arduino-ft232r (Arduino: FT232R connected to ISP, miso = CTS
X3(1), sck = DSR X3(2), mosi = DCD X3(3), reset = RI X3(4))
+ diecimila (alias for arduino-ft232r)
- pickit2
- Atmel JTAGICE3
- buspirate_bb (TPI programming using the BusPirate in bitbang mode)
* Bugfixes
- bug #34027: avrdude AT90S1200 Problem
- bug #34518: loading intel hex files > 64k using record-type 4
- patch #7667: Minor memory handling fixes
- patch #7680: Fixing timeout problem in ser_recv in ser_win32.c
- patch #7693: Fix config file atmel URLs (+ URLs in
avrdude.texi and avrpart.h)
- bug #21663: AT90PWM efuse incorrect, bug #30438: efuse bits
written as 0 on at90pwmxx parts
- bug #35261: avrftdi uses wrong interface in avrftdi_paged_(write|load)
- patch #7437 modifications to Bus Pirate module
- patch #7686 Updating buspirate ascii mode to current firmware,
use AUX as clock generator, and setting of serial receive
timeout
- bug #34768 Proposition: Change the name of the AVR32 devices
- patch #7718: Merge global data of avrftdi in a private data
structure
- bug #35208: avrdude 5.11 on freebsd 8.2-STABLE does not reset
Arduino Uno properly
- bug #34518: loading intel hex files > 64k using record-type 4
(Extended Linear Address Record)
- bug #34027: avrdude AT90S1200 Problem
- bug #30451: Accessing some Xmega memory sections gives not
supported error
- bug #28744: Can't load bootloader to xmega128a1
- bug #29019: pagel/bs2 warning when uploading using stk500 to xmega
- bug #30756: When setting SUT to 64ms on XMEGA, avrdude doesn't
read device signature
- bug #37265: wrong page sizes for XMega64xx in avrdude.conf
- bug #37942: Latest SVN can't program in dragon_jtag mode
- patch #7876 JTAGICE mkII fails to connect to attiny if debugwire
is enabled AND target has a very slow clock
- bug #39893: Verification failure with AVRISPmkII and Xmega
- bug #38713: Compilation of the documentation breaks with texinfo-5
- bug #38023: avrdude doesn't return an error code when attempting
to upload an invalid Intel HEX file
- bug #39794: warnings when building avrdude 6.0rc1 under CentOS 6.4
- bug #35800: Compilation error on certain systems if parport is disabled
- bug #38307: Can't write usersig of an xmega256a3
- bug #38580: Current svn head, xmega and fuses, all fuses tied to fuse0
- bug #39691: Buffer overrun when reading EEPROM byte with JTAGICE3
- bug #38951: AVR109 use byte offset instead of word offset
- patch #7769: Write flash fails for AVR910 programmers
- bug #38732: Support for ATtiny1634
- bug #36901: flashing Atmega32U4 EEPROM produces garbage on chip
- bug #28344: chip_erase_delay too short for ATmega324P, 644, 644P, and 1284P
- bug #34277: avrdude reads wrong byte order if using avr911 (aka butterfly)
- bug #35456: The progress bar for STK500V2 programmer is "wrong".
- patch #5708: avrdude should make 10 synchronization attempts instead of just one
- patch #7606: ATtiny43u support
- patch #7657: Add ATmega406 support for avrdude using DRAGON + JTAG
- bug #35474: Feature request: print fuse values in safemode output.
- patch #7710: usb_libusb: Check VID/PID before opening device
- [no-id]: Fix SCK period adjustment for STK500v2
- bug #40040: Support for ATtiny20 and ATtiny40
* Internals:
- Restructuring and compacting programmer definition part of
grammar for config file.
- Cleanup of parser code, removing unused definitions/
functions. Using yylex_destroy if available.
- Fixed some more memory leaks, added cleanup code at program exit
(to minimize the number of non-freed memory blocks reported by
valgrind)
- Fixed some findings reported by cppcheck.
Version 5.11:
* New devices supported:
- ATmega88P/168P
- ATmega8U2/16U2/32U2
- ATtiny4313
* New programmers supported:
- TPI programming through bitbang programmers (both, serial
and parallel ones)
- FT2232 (and relatives) based programmers (MPSSE bitbang mode)
- Wiring environment (http://wiring.org.co/)
- butterfly-style bootloader of the Mikrokopter.de device
* Bugfixes
Version 5.10:
* Bugfixes
- bug #28660: Problem with loading intel hex rom files that exceed
0x10000 bytes
- see ChangeLog for further details
* New Features
- (JTAG ICE / AVR Dragon) apply external reset if JTAG ID could
not be read
Version 5.9:
* New devices supported:
- AVR32A0512 (JTAGMKII only)
- ATmega32U4
- ATtiny4
- ATtiny5
- ATtiny9
- ATtiny10
* New programmers supported:
- BusPirate
- Arduino
- JTAGICEmkII and AVR Dragon in PDI mode (ATxmega devices)
- STK600 and AVRISP mkII in TPI mode (ATtiny4/5/9/10)
* Bugfixes
- see ChangeLog and ChangeLog-2009 for details
Version 5.8:
* Bugfixes; most importantly, fix a serious memory corruption for
that JTAG ICE mkII and AVR Dragon in ISP/HVSP/PP mode.
Version 5.7:
* New devices supported:
- ATXMEGA64A1
- ATXMEGA192A1
- ATXMEGA256A1
- ATXMEGA64A3
- ATXMEGA128A3
- ATXMEGA192A3
- ATXMEGA256A3
- ATXMEGA256A3B
- ATXMEGA16A4
- ATXMEGA32A4
- ATXMEGA64A4
- ATXMEGA128A4
* Major Xmega fixes for the JTAG ICE mkII (patch #6825)
* Bugfixes.
Version 5.6:
* New devices supported:
- AT90USB82
- AT90USB162
- ATtiny88
- ATmega328P
- ATmega1284P
- ATmega128RFA1
- ATxmega128A1 rev D
- ATxmega128A1
- ATxmega256A3
* New programmers supported:
- AT89ISP cable (patch #6069)
- Arduino
* Add support for the -x option to pass extended parameters to the
programmer backend.
* Add support for JTAG daisy-chains, using the -x daisychain=
option.
Add initial support for the Atmel STK600, for "classic" AVRs (AT90, ATtiny, ATmega) in both, ISP and high-voltage programming modes. * Makefile.am: Add -lm. * avrdude.conf.in: Add stk600, stk600pp, and stk600hvsp. * config_gram.y: Add support for the stk600* keywords. * lexer.l: (Ditto.) * pgm.h: Add the "chan" parameter to set_varef(). * stk500.c: (Ditto.) * serial.h: Add USB endpoint support to struct filedescriptor. * stk500v2.c: Implement the meat of the STK600 support. * stk500v2.h: Add new prototypes for stk600*() programmers. * stk500v2_private.h: Add new constants used in the STK600. * term.c: Add AREF channel support. * usb_libusb.c: Automatically determine the correct write endpoint ID, the STK600 uses 0x83 while all other tools use 0x82. Propagate the EP to use through struct filedescriptor. * usbdevs.h: Add the STK600 USB product ID. * tools/get-stk600-cards.xsl: XSL transformation for targetboards.xml to obtain the list of socket and routing card IDs, to be used in stk500v2.c (for displaying the names). * tools/get-stk600-devices.xsl: XSL transformation for targetboards.xml to obtain the table of socket/routing cards and their respective AVR device support for doc/avrdude.texi. * avrdude.1: Document all the STK600 stuff. * doc/avrdude.texi: Ditto. Added a new chapter for Programmer Specific Information. Thanks to Eirik Rasmussen from Atmel Norway for his support in getting this code running within that short amount of time! git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@768 81a1dc3b-b13d-400b-aceb-764788c761c2
2008-03-14 13:00:08 +00:00
* Add support for the Atmel STK600 for "classic" AVRs (AT90, ATtiny,
ATmega), using either ISP or high-voltage programming modes.
* Add support for the -x devcode extended parameter to the avr910
programmer, to allow overriding the device code sent to the
programmer.
* Add support for the Crossbow MIB510 programmer (patch #6074, #6542).
* Add support to bootstrap with GNU autoconf 2.61, and automake 1.10,
respectively.
* Add support for ATxmega128A1 (including the revision D engineering
samples) for STK600 and AVRISPmkII tools using PDI
* The option combination -tF now enters terminal mode even if the
device initialization failed, so the user can modify programmer
parameters (like Vtarget).
* Add preliminary support for ATxmega128A1 for the JTAG ICE mkII using
JTAG.
* Add support for direct SPI transfers (bug #25156).
* Bugfixes.
Version 5.5:
* Add support for the USBtinyISP programmer (patch #6233)
* Add support for the C2N232I serial bitbang programmer (patch #6121)
* Bugfixes.
Version 5.4:
* New devices supported:
- AT90PWM2B/AT90PWM3B
* Bugfixes.
* Source code rearranged so that the functionality is now built
into a libavrdude.a library where main.c is currently the only
existing frontend.
* Implement ATmega256x support for butterfly/avr109.
Version 5.3.1:
* Add support for the AVR Dragon (all modes: ISP, JTAG, HVSP, PP,
debugWire).
* Add support for debugWire (both, JTAG ICE mkII, and AVR Dragon).
* Add support for the AVR Doper USB HID-class programmer.
* Bugfixes.
Version 5.2:
* New devices supported:
- AT90USB646/647/1286/1287
- ATmega2560/2561
- ATmega325/3250/645/6450
- ATtiny11 (HVSP only device)
- ATtiny261/461/861
* Fixed paged flash write operations for AT90PWMx devices
(error in datasheet).
* Add signature verification.
* Add high-voltage mode programming for the STK500 (both,
parallel, and high-voltage serial programming).
* Add support for using the JTAG ICE mkII as a generic ISP
programmer.
* Allow for specifying the ISP clock delay as an option for
bit-bang programming adapters.
* Add support for Thomas Fischl's USBasp low-cost USB-attached
programmer.
* The "stk500" programmer type is now implemented as a stub
that tries to probe for either "stk500v1" or "stk500v2".
* Many bugfixes.
Version 5.1:
* New devices supported:
- ATmega640/1280/1281
- ATtiny24/44/84
* JTAG mkII support now works with libusb-win32, too
* JTAG ICE mkI support has been added
* Solaris support has been added (including ecpp(7D) parallel-port
bit-bang mode)
Version 5.0:
* Support for JTAGICE MkII device
* Support for STK500 Version 2 Protocol
* New devices supported:
- AT90CAN128
- ATmega329x/649x
- ATmega164/324/644
- AT90PWM2/3,
- ATmega164/324/644
- ATmega329x/649x
- ATtiny25/45/85
* Support for serial bit-bang adapters: Ponyprog serial, UISP DASA,
UISP DASA3.
* DAPA programmer pinout supported
* New "safemode" feature where fuse bits are verified before exit
and if possible recovered if they have changed. This is intended
to protect against changed fuses which were not requested which is
reported to sometimes happen due to improper power supply or other
reasons.
* Various fixes for avr910 and butterfly programmers
* Full support for AVR109 boot loaders (butterfly)
* Adding -q -q suppresses most terminal output
Version 4.4.0:
* Native Win32 support: The windows build doesn't need Cygwin
anymore. Additionally, the delay timing on windows should be
more accurate now.
Contributed by Martin Thomas
* Add support for
- ATmega48, ATmega88 (contributed by Galen Seitz)
- ATtiny2313 (contributed by Bob Paddock)
- ATtiny13 (contributed by Pawel Moll)
* Added command to change the SCK of STK500-programmers. Now it
is possible to program uC with slow oscillator.
Contributed by Galen Seitz
* Baudrate for serial programmers (STK500 and AVR910) is
configurable in the config or at the command-line.
This way some more tweaked bootloaders and programmers can be used.
* Deprecated options have been removed.
Now the "-U" option must be used.
* MacOS X now supported by default.
Version 4.3.0:
* Added support for "Butterfly" evaluation board.
* Make cycle-count work with AVR910-programmers.
* Added "Troubleshooting"-Appendix to the manual.
* Add ATmega8515 support.
Contributed by: Matthias Wei<65>er <matthias@matwei.de>
* Add ATmega64 support.
Contributed by: Erik Christiansen <erik@dd.nec.com.au>
* Improved polling algorithm to speed up
programming of byte oriented parallel programmers.
Contributed by: Jan-Hinnerk Reichert <jan-hinnerk_reichert@hamburg.de>
* Add "fuse" and "lock" definitions for the AT90S8535.
* STK500 skips empty pages in paged write resulting in faster downloads
when there are empty blocks in between code (such as files that contain
application code and bootloader code).
Version 4.2.0:
* Add basic support for reading and writing fuses via SPI with avr910
programmers. Submitted by
Jan-Hinnerk Reichert <jan-hinnerk_reichert@hamburg.de>.
* Perform an auto erase before programming if the flash memory is
anywhere specified to be written by any of the -U requests. Old
style memory specification options (-f, -i, -I, -m, and -o) are
deprecated in favor of the new -U options. Auto erase is disabled
if any of the old-style options (specifically -i and -o) are
specified.
* Add new -U option for specifying programming operations - allows
multiple memory operations on a single command line.
* New progress reporting, looks nicer and is nicer to wrapper
environments such as emacs.
* Fix long-standing timing (verify) problems on Windows platform.
Submitted by Alex Shepherd <ashepherd@wave.co.nz>.
* Add new file format option - 'm' for "immediate mode." In this
case, the filename argument of the -o, -i, or -U options is
treated as the data for uploading - useful for specifying fuse
bits without having to create a single-byte file for uploading.
* Add support for displaying and setting the various STK500 operational
parameters (Vtarget, Varef, Master clock).
* Add 'picoweb' programming cable programmer.
Contributed by Rune Christensen <rune.christensen@adslhome.dk>.
* Add support for the sp12 programmer. Submitted by
Larry Barello <larryba@barrello.net>.
Version 4.1.0
* Add support for the Bascom SAMPLE programmer. Submitted by
Larry Barello <larryba@barrello.net>.
* Add support for avr910 type programmers (mcu00100, pavr avr910, etc).
* Support new devices: ATmega8535, ATtiny26
Version 4.0.0
* Now support Linux - added by "Theodore A. Roth" <troth@openavr.org>.
* Now support Windows - added by "Eric B. Weddington" <eric@ecentral.com>.
* Use 'configure' scripts to tailor the code to the system avrdude
is getting ready to be compiled on - added by "Theodore A. Roth"
<troth@openavr.org>.
* Motorola S-Record support - submitted by "Alexey V.Levdikov "
<tsar@kemford.com>.
* Support parallel programming on the STK500. Introduce 'pagel' and
'bs2' keywords to the config file for this purpose.
* Add support for the AT90S2343
* Add support for the ATmega169
* Add ability to specify system defaults within the config file
(default parallel port, default serial port).
* Specify the default programmer seperately from the programmer
definition. This is now done in the config file using the
'default_programmer' keyword.
* Support a per-user config file (~/.avrduderc) so that one can
override system wide defaults if desired.
* Follow the datasheet more closely for several parts in the "retry"
code when entering programming mode fails initially. Introduce
'retry_pulse' to the config file for this purpose.
Version 3.1.0
* This change represents a name change only. There is currently an
effort to port AVRPROG to other platforms including Linux and
Windows. Since Atmel's programmer binary that's included within
their AVR Studio software is named AVRPROG.EXE on the Windows OS,
there is the chance for confusion if we keep calling this program
AVRPROG as well. Up until now the name hasn't really been a
problem since there was no chance to confuse 'avrprog' on Unix
with Atmel's AVRPROG because Atmel's tools only run on Windows.
But with the Unix 'avrprog' possibly being ported to Windows, I
felt a name change was the best way to avoid problems.
So - from this point forward, my FreeBSD Unix program formerly
known as AVRPROG will subsequently be known as AVRDUDE (AVR
Downloader/UploaDEr).
This change also represents a time when the AVRDUDE sources move
from my own private repository to a public repository. This will
give other developers a chance to port AVRDUDE to other platforms
and extend its functionality to support additional programming
hardware, etc.
So goodbye AVRPROG, welcome AVRDUDE!
Version 3.0.0
* Rewrite parts of the code to make it easy to support other types
of programmers besides the directly connected parallel port
programmer (PPI).
* Add support for Atmel's STK500 programmer/development board. The
STK500's "paged mode" read/write is supported which makes this
programmer very fast. This is sorely needed on parts with large
memories such as the ATmega128. My 12K test program burns in
about 5 seconds, add another 5 to read it back out for
verification.
Version 2.1.5:
* When getting ready to initiate communications with the AVR device,
first pull /RESET low for a short period of time before enabling
the buffer chip. This sequence allows the AVR to be reset before
the buffer is enabled to avoid a short period of time where the
AVR may be driving the programming lines at the same time the
programmer tries to. Of course, if a buffer is being used, then
the /RESET line from the programmer needs to be directly connected
to the AVR /RESET line and not via the buffer chip.
Feature contributed by Rick C. Petty <rick@KIWI-Computer.com>.
* When in interactive terminal mode and dumping memory using the
'dump <memtype>' command without any address information, and the
end of memory is reached, wrap back around to zero on the next
invocation.
Version 2.1.4:
* Fix -Y option.
Version 2.1.3:
* Be backward compatible when reading 2-byte rewrite cycle counters
as written by avrprog version 2.1.0. Version 2.1.1 changed over
to a 4-byte counter, which caused avrprog versions 2.1.1 and 2.1.2
to report a negative count for parts that were initialized using
version 2.1.0. Thanks to Joerg Wunsch for noticing this.
Version 2.1.2:
* Add '-V' option to disable automatic verify check with uploading
data.
Version 2.1.1:
* Fix ATmega128 instruction sequences for reading fuse bits -
contributed by Joerg Wunsch.
* Modify erase-rewrite cycle counter code to use a 4 byte counter
instead of a two byte counter.
Version 2.1.0:
* Implement a per-part erase-rewrite cycle counter; requires the use
of two bytes of EEPROM memory.
Version 2.0.5:
* Support for ATtiny15 - contributed by Asher Hoskins
Version 2.0.4:
* Config file fixes for various parts.
Version 2.0.3:
* Work around problem programming fuse bits on parts like the
at90s4433 as described in the following errata:
http://www.atmel.com/atmel/acrobat/doc1280.pdf
* Add part definition for at90s4414, at90s4433.
* Add fuse/lock bit memory instructions for the at90s1200,
at90s2333, at90s4433 and at90s8515.
* Fix setting of programmer status LEDs under certain write-fail
conditions.
Version 2.0.2 :
* Fix writing to read-only memories such as the lock bits of the
AT90S2313.
* Copyright updates.
Version 2.0.1 :
* Use correct parallel port pins for VCC.
* Add programmer definition for Atmel's STK200.
* Add programmer definition for the AVR3 board.
* Fix address bit encoding for many parts.
* Allow the ``BUFF'' signal to be asserted by multiple pins of the
parallel port (like VCC) instead of just one. The STK200 appears
to need this feature.
Version 2.0.0 :
* Add support for programming fuse and lock bits if supported by the
part.
* Move instruction encoding into the config file. Now any part can
be supported as long as it uses the same basic serial programming
instruction format.
* Add part definitions for the ATMega163 and ATMega8 devices.
Version 1.4.3 :
* Mostly internal code cleanup.
Version 1.4.2 :
* Fixes for ATMega paged memory support.
* Support for ATMega16 device.
Version 1.4.1 :
* No functional changes, update to Copyrights only.
Version 1.4.0 :
* Add part definitions to the config file.
* Add initial support for Atmel's ATMega paged memory parts.
* Config file documentation added.
* Add a definition for the Dontronics DT006 programmer.
* Fix Intel Hex support for addresses larger than 64k.
Version 1.3.0 :
* Make programmer pin assignments configurable.
Version 1.2.2 :
* Initial public release.