Files
led-hoop/cad/pico_hoop_box.scad
2026-11-08 22:20:48 +13:00

244 lines
8.3 KiB
OpenSCAD
Raw Permalink Blame History

This file contains ambiguous Unicode characters
This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.
// Pico enclosure that saddles a 25mm hoop bar (900mm hoop diameter).
// OpenSCAD 2021+: F5 preview, F6 render, export STL.
//
// Prints as body + lid. Clip onto the bar, secure with zip-ties through the
// saddle slots. Lid snaps into the bay rim.
//
// Frame: bar centre at origin, +Z away from hoop centre, +Y along hoop,
// +X across the bar.
/* [Hoop] */
// hoop_diameter kept for reference / future curved saddle (~0.9mm sag over 58mm)
hoop_diameter = 900; // tube centerline diameter (mm)
bar_diameter = 25; // bar / tube OD (mm)
bar_clearance = 0.35; // radial slip around the bar
/* [Pico bay] */
pico_length = 52.5; // clearance along hoop
pico_width = 22.0; // clearance across bar
pico_height = 12.0; // board + headers / wiring
wall = 2.0;
lid_thick = 2.0;
lid_lip = 1.4;
lid_clear = 0.3;
/* [Saddle / clamp] */
saddle_wrap_deg = 230; // >180 so it snaps onto the bar
saddle_wall = 2.6;
saddle_length = 58; // along hoop (mm)
ziptie_w = 3.8;
ziptie_h = 2.0;
ziptie_inset = 9; // from each saddle end toward centre
ear_len = 7; // zip-tie ears sticking out each side
ear_thick = 3;
/* [Ports / access] */
// Pico USB end faces +Y. Board is centred on the bay; hole centres are
// 2mm in from each short edge of the 51mm PCB.
board_length = 51.0;
board_width = 21.0;
board_thick = 1.0;
// Micro-USB B cutout (plug clearance)
usb_w = 9.0;
usb_h = 4.2;
usb_z_above_board = 0.2; // opening starts just above PCB top
// Power-out cable (opposite USB, -Y end) — LED / battery feed
power_hole_d = 6.0;
// BOOTSEL through lid (from USB-end PCB edge / board centre)
// Measured from Pico mechanical layout: ~5.7mm from USB edge, ~4.8mm left of centre.
bootsel_from_usb_edge = 5.7;
bootsel_x = -4.8; // -X when USB is at +Y
bootsel_hole_d = 4.5;
/* [Pico mounting posts] */
// Official Pico hole centres: 47.0 x 11.4 mm
hole_span_l = 47.0;
hole_span_w = 11.4;
post_od = 4.2;
post_id = 1.7; // M2 self-tap
post_h = 3.0;
/* [Quality] */
$fn = 80;
// ---------------------------------------------------------------------------
bar_r = bar_diameter / 2;
saddle_ir = bar_r + bar_clearance;
saddle_or = saddle_ir + saddle_wall;
bay_inner_l = pico_length;
bay_inner_w = pico_width;
bay_inner_h = pico_height;
bay_outer_l = bay_inner_l + 2 * wall;
bay_outer_w = max(bay_inner_w + 2 * wall, 2 * saddle_or + 1);
bay_outer_h = bay_inner_h + wall;
bay_floor_z = saddle_or;
// 2D clip profile in the plane normal to the bar (X = across, Y = up).
module saddle_profile() {
wrap = saddle_wrap_deg;
// Keep the top half solid (shoulders under the bay) and a partial ring below.
difference() {
union() {
// outer disc, then cut to wrap angle from the bottom
circle(r = saddle_or);
// rectangular shoulders up to bay floor
translate([-saddle_or, 0])
square([2 * saddle_or, saddle_or + 0.01]);
}
circle(r = saddle_ir);
// remove the open sector at the bottom (clip mouth)
half_gap = (360 - wrap) / 2;
rotate(-(90 + wrap / 2))
pie_slice(saddle_or + 1, 360 - wrap);
}
}
module pie_slice(r, ang) {
// Triangle fan covering `ang` degrees starting at +X, CCW.
steps = max(3, ceil(ang / 4));
polygon(concat([[0, 0]],
[for (i = [0:steps]) [r * cos(i * ang / steps), r * sin(i * ang / steps)]]));
}
module pico_posts() {
for (x = [-hole_span_w / 2, hole_span_w / 2])
for (y = [-hole_span_l / 2, hole_span_l / 2])
translate([x, y, 0])
difference() {
cylinder(h = post_h, d = post_od);
translate([0, 0, -0.05])
cylinder(h = post_h + 0.1, d = post_id, $fn = 20);
}
}
module body() {
// USB opening bottom (board sits on standoffs)
usb_z = bay_floor_z + wall + post_h + board_thick + usb_z_above_board;
difference() {
union() {
// Saddle — extruded along the bar (+Y). Hoop curvature over 58mm is
// ~0.9mm sag; ignored so the part prints and clips simply.
translate([0, saddle_length / 2, 0])
rotate([90, 0, 0])
linear_extrude(height = saddle_length, convexity = 8)
saddle_profile();
// Electronics bay on top of the saddle
translate([-bay_outer_w / 2, -bay_outer_l / 2, bay_floor_z])
cube([bay_outer_w, bay_outer_l, bay_outer_h]);
}
// Bay cavity
translate([-bay_inner_w / 2, -bay_inner_l / 2, bay_floor_z + wall])
cube([bay_inner_w, bay_inner_l, bay_inner_h + 0.2]);
// Lid ledge
translate([
-(bay_inner_w + 2 * lid_lip) / 2,
-(bay_inner_l + 2 * lid_lip) / 2,
bay_floor_z + bay_outer_h - lid_thick
])
cube([
bay_inner_w + 2 * lid_lip,
bay_inner_l + 2 * lid_lip,
lid_thick + 0.15
]);
// USB cutout — +Y end, height matches board on standoffs
translate([0, bay_outer_l / 2 - wall / 2, usb_z + usb_h / 2])
cube([usb_w, wall + 2, usb_h], center = true);
// Power-out hole — −Y end (opposite USB), for LED / battery wires
translate([
0,
-(bay_outer_l / 2 - wall / 2),
bay_floor_z + wall + power_hole_d / 2 + 1
])
rotate([90, 0, 0])
cylinder(h = wall + 2, d = power_hole_d, center = true);
// Ensure bar bore is clear through the whole saddle
rotate([90, 0, 0])
cylinder(h = saddle_length + 2, r = saddle_ir, center = true);
}
// Zip-tie ears on both sides — strap goes around bar + saddle
for (sx = [-1, 1])
translate([sx * (saddle_or + ear_len / 2 - 1.2), 0, -ear_thick / 2])
difference() {
cube([ear_len + 2.4, saddle_length - 2 * ziptie_inset + ziptie_w, ear_thick], center = true);
// don't fill the bar bore
rotate([90, 0, 0])
cylinder(h = saddle_length, r = saddle_ir, center = true);
for (sy = [-1, 1])
translate([0, sy * (saddle_length / 2 - ziptie_inset), 0])
cube([ear_len + 4, ziptie_w, ziptie_h], center = true);
}
// Board standoffs
translate([0, 0, bay_floor_z + wall])
pico_posts();
// Lid retention nubs
nub_z = bay_floor_z + bay_outer_h - lid_thick - 1.0;
for (x = [-1, 1])
translate([x * (bay_inner_w / 2 - 0.25), 0, nub_z])
rotate([90, 0, 0])
cylinder(h = 8, d = 1.5, center = true, $fn = 16);
}
module lid() {
outer_l = bay_inner_l + 2 * lid_lip - lid_clear;
outer_w = bay_inner_w + 2 * lid_lip - lid_clear;
inner_l = bay_inner_l - lid_clear;
inner_w = bay_inner_w - lid_clear;
// BOOTSEL in body frame: USB end at +Y. Lid shares the same XY origin.
bootsel_y = board_length / 2 - bootsel_from_usb_edge;
difference() {
union() {
translate([-outer_w / 2, -outer_l / 2, 0])
cube([outer_w, outer_l, lid_thick]);
translate([-inner_w / 2, -inner_l / 2, -lid_lip])
cube([inner_w, inner_l, lid_lip]);
}
// BOOTSEL access (finger / pen)
translate([bootsel_x, bootsel_y, -lid_lip - 0.5])
cylinder(h = lid_thick + lid_lip + 1, d = bootsel_hole_d, $fn = 32);
// Nail notch on USB end
translate([0, outer_l / 2 - 0.5, lid_thick / 2])
rotate([0, 90, 0])
cylinder(h = 14, d = 3.2, center = true, $fn = 24);
// Snap recesses matching body nubs
for (x = [-1, 1])
translate([x * (inner_w / 2 - 0.15), 0, -0.6])
rotate([90, 0, 0])
cylinder(h = 9, d = 1.7, center = true, $fn = 16);
}
}
module print_layout() {
body();
translate([bay_outer_w + 14, 0, lid_thick])
rotate([0, 180, 0])
lid();
}
module preview_on_bar() {
body();
translate([0, 0, bay_floor_z + bay_outer_h - lid_thick])
color("steelblue", 0.7) lid();
color("silver", 0.35)
rotate([90, 0, 0])
cylinder(h = 90, d = bar_diameter, center = true);
}
print_layout();
// preview_on_bar();