// Pico enclosure that saddles a 25mm hoop bar (900mm hoop diameter). // OpenSCAD 2021+: F5 preview, F6 render, export STL. // // Prints as body + lid. Clip onto the bar, secure with zip-ties through the // saddle slots. Lid snaps into the bay rim. // // Frame: bar centre at origin, +Z away from hoop centre, +Y along hoop, // +X across the bar. /* [Hoop] */ // hoop_diameter kept for reference / future curved saddle (~0.9mm sag over 58mm) hoop_diameter = 900; // tube centerline diameter (mm) bar_diameter = 25; // bar / tube OD (mm) bar_clearance = 0.35; // radial slip around the bar /* [Pico bay] */ pico_length = 52.5; // clearance along hoop pico_width = 22.0; // clearance across bar pico_height = 12.0; // board + headers / wiring wall = 2.0; lid_thick = 2.0; lid_lip = 1.4; lid_clear = 0.3; /* [Saddle / clamp] */ saddle_wrap_deg = 230; // >180 so it snaps onto the bar saddle_wall = 2.6; saddle_length = 58; // along hoop (mm) ziptie_w = 3.8; ziptie_h = 2.0; ziptie_inset = 9; // from each saddle end toward centre ear_len = 7; // zip-tie ears sticking out each side ear_thick = 3; /* [Ports / access] */ // Pico USB end faces +Y. Board is centred on the bay; hole centres are // 2mm in from each short edge of the 51mm PCB. board_length = 51.0; board_width = 21.0; board_thick = 1.0; // Micro-USB B cutout (plug clearance) usb_w = 9.0; usb_h = 4.2; usb_z_above_board = 0.2; // opening starts just above PCB top // Power-out cable (opposite USB, -Y end) — LED / battery feed power_hole_d = 6.0; // BOOTSEL through lid (from USB-end PCB edge / board centre) // Measured from Pico mechanical layout: ~5.7mm from USB edge, ~4.8mm left of centre. bootsel_from_usb_edge = 5.7; bootsel_x = -4.8; // -X when USB is at +Y bootsel_hole_d = 4.5; /* [Pico mounting posts] */ // Official Pico hole centres: 47.0 x 11.4 mm hole_span_l = 47.0; hole_span_w = 11.4; post_od = 4.2; post_id = 1.7; // M2 self-tap post_h = 3.0; /* [Quality] */ $fn = 80; // --------------------------------------------------------------------------- bar_r = bar_diameter / 2; saddle_ir = bar_r + bar_clearance; saddle_or = saddle_ir + saddle_wall; bay_inner_l = pico_length; bay_inner_w = pico_width; bay_inner_h = pico_height; bay_outer_l = bay_inner_l + 2 * wall; bay_outer_w = max(bay_inner_w + 2 * wall, 2 * saddle_or + 1); bay_outer_h = bay_inner_h + wall; bay_floor_z = saddle_or; // 2D clip profile in the plane normal to the bar (X = across, Y = up). module saddle_profile() { wrap = saddle_wrap_deg; // Keep the top half solid (shoulders under the bay) and a partial ring below. difference() { union() { // outer disc, then cut to wrap angle from the bottom circle(r = saddle_or); // rectangular shoulders up to bay floor translate([-saddle_or, 0]) square([2 * saddle_or, saddle_or + 0.01]); } circle(r = saddle_ir); // remove the open sector at the bottom (clip mouth) half_gap = (360 - wrap) / 2; rotate(-(90 + wrap / 2)) pie_slice(saddle_or + 1, 360 - wrap); } } module pie_slice(r, ang) { // Triangle fan covering `ang` degrees starting at +X, CCW. steps = max(3, ceil(ang / 4)); polygon(concat([[0, 0]], [for (i = [0:steps]) [r * cos(i * ang / steps), r * sin(i * ang / steps)]])); } module pico_posts() { for (x = [-hole_span_w / 2, hole_span_w / 2]) for (y = [-hole_span_l / 2, hole_span_l / 2]) translate([x, y, 0]) difference() { cylinder(h = post_h, d = post_od); translate([0, 0, -0.05]) cylinder(h = post_h + 0.1, d = post_id, $fn = 20); } } module body() { // USB opening bottom (board sits on standoffs) usb_z = bay_floor_z + wall + post_h + board_thick + usb_z_above_board; difference() { union() { // Saddle — extruded along the bar (+Y). Hoop curvature over 58mm is // ~0.9mm sag; ignored so the part prints and clips simply. translate([0, saddle_length / 2, 0]) rotate([90, 0, 0]) linear_extrude(height = saddle_length, convexity = 8) saddle_profile(); // Electronics bay on top of the saddle translate([-bay_outer_w / 2, -bay_outer_l / 2, bay_floor_z]) cube([bay_outer_w, bay_outer_l, bay_outer_h]); } // Bay cavity translate([-bay_inner_w / 2, -bay_inner_l / 2, bay_floor_z + wall]) cube([bay_inner_w, bay_inner_l, bay_inner_h + 0.2]); // Lid ledge translate([ -(bay_inner_w + 2 * lid_lip) / 2, -(bay_inner_l + 2 * lid_lip) / 2, bay_floor_z + bay_outer_h - lid_thick ]) cube([ bay_inner_w + 2 * lid_lip, bay_inner_l + 2 * lid_lip, lid_thick + 0.15 ]); // USB cutout — +Y end, height matches board on standoffs translate([0, bay_outer_l / 2 - wall / 2, usb_z + usb_h / 2]) cube([usb_w, wall + 2, usb_h], center = true); // Power-out hole — −Y end (opposite USB), for LED / battery wires translate([ 0, -(bay_outer_l / 2 - wall / 2), bay_floor_z + wall + power_hole_d / 2 + 1 ]) rotate([90, 0, 0]) cylinder(h = wall + 2, d = power_hole_d, center = true); // Ensure bar bore is clear through the whole saddle rotate([90, 0, 0]) cylinder(h = saddle_length + 2, r = saddle_ir, center = true); } // Zip-tie ears on both sides — strap goes around bar + saddle for (sx = [-1, 1]) translate([sx * (saddle_or + ear_len / 2 - 1.2), 0, -ear_thick / 2]) difference() { cube([ear_len + 2.4, saddle_length - 2 * ziptie_inset + ziptie_w, ear_thick], center = true); // don't fill the bar bore rotate([90, 0, 0]) cylinder(h = saddle_length, r = saddle_ir, center = true); for (sy = [-1, 1]) translate([0, sy * (saddle_length / 2 - ziptie_inset), 0]) cube([ear_len + 4, ziptie_w, ziptie_h], center = true); } // Board standoffs translate([0, 0, bay_floor_z + wall]) pico_posts(); // Lid retention nubs nub_z = bay_floor_z + bay_outer_h - lid_thick - 1.0; for (x = [-1, 1]) translate([x * (bay_inner_w / 2 - 0.25), 0, nub_z]) rotate([90, 0, 0]) cylinder(h = 8, d = 1.5, center = true, $fn = 16); } module lid() { outer_l = bay_inner_l + 2 * lid_lip - lid_clear; outer_w = bay_inner_w + 2 * lid_lip - lid_clear; inner_l = bay_inner_l - lid_clear; inner_w = bay_inner_w - lid_clear; // BOOTSEL in body frame: USB end at +Y. Lid shares the same XY origin. bootsel_y = board_length / 2 - bootsel_from_usb_edge; difference() { union() { translate([-outer_w / 2, -outer_l / 2, 0]) cube([outer_w, outer_l, lid_thick]); translate([-inner_w / 2, -inner_l / 2, -lid_lip]) cube([inner_w, inner_l, lid_lip]); } // BOOTSEL access (finger / pen) translate([bootsel_x, bootsel_y, -lid_lip - 0.5]) cylinder(h = lid_thick + lid_lip + 1, d = bootsel_hole_d, $fn = 32); // Nail notch on USB end translate([0, outer_l / 2 - 0.5, lid_thick / 2]) rotate([0, 90, 0]) cylinder(h = 14, d = 3.2, center = true, $fn = 24); // Snap recesses matching body nubs for (x = [-1, 1]) translate([x * (inner_w / 2 - 0.15), 0, -0.6]) rotate([90, 0, 0]) cylinder(h = 9, d = 1.7, center = true, $fn = 16); } } module print_layout() { body(); translate([bay_outer_w + 14, 0, lid_thick]) rotate([0, 180, 0]) lid(); } module preview_on_bar() { body(); translate([0, 0, bay_floor_z + bay_outer_h - lid_thick]) color("steelblue", 0.7) lid(); color("silver", 0.35) rotate([90, 0, 0]) cylinder(h = 90, d = bar_diameter, center = true); } print_layout(); // preview_on_bar();