- led-simulator: the rig runs the C++ led-driver as WebAssembly (sim-driver/), one single-threaded worker per bar, no cross-origin isolation needed. Rooms (one JSON per room) with an on-page editor, and a pattern gallery. The Python server, Pyodide boot and ring buffer are removed. - sim-controller sim_rig.c: serves /sim/ from an embedded pack, the page's WebSocket and the rooms/flash API. The desktop build embeds it too. - bridge.c: a "browser" bridge kind that carries ESP-NOW frames to the page; devices announced through it are marked sim. - UI: Simulator in the Menu, split view with resize and pop-out, swipe between controller and rig on phones; SIM/REAL badges in Devices. - Fades: preset pushes and Wi-Fi driver bodies always carry fade and beat_time, so "off" no longer inherits an earlier fade. - Also the sequences-v2 work in progress: desktop port, bridge firmware, serial bridge, Wi-Fi drivers, sequence timeline, audio and API changes. - led-driver: ESP-NOW link, beat sync, control messages, sim hooks. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
86 lines
2.2 KiB
Plaintext
86 lines
2.2 KiB
Plaintext
menu "Bridge Ethernet (W5500)"
|
|
|
|
config BRIDGE_ETH
|
|
bool "W5500 Ethernet with a UDP bridge"
|
|
default y if IDF_TARGET_ESP32S3
|
|
default n
|
|
help
|
|
The board has a W5500 on SPI, wired to the network. It takes UDP datagrams on BRIDGE_ETH_PORT
|
|
(dst_mac + packet, sent on ESP-NOW) and sends frames it hears back to the last sender (src_mac + packet).
|
|
Its address is logged over the USB link once DHCP answers.
|
|
|
|
config BRIDGE_ETH_PORT
|
|
int "UDP port"
|
|
depends on BRIDGE_ETH
|
|
default 8766
|
|
|
|
config BRIDGE_ETH_AUDIO_PORT
|
|
int "UDP control port (microphone audio and HELLO)"
|
|
depends on BRIDGE_ETH
|
|
default 8767
|
|
|
|
config BRIDGE_ETH_SPI_CLOCK_MHZ
|
|
int "SPI clock (MHz)"
|
|
depends on BRIDGE_ETH
|
|
range 5 80
|
|
default 20
|
|
|
|
config BRIDGE_ETH_SCLK_GPIO
|
|
int "SCLK GPIO (XIAO D8)"
|
|
depends on BRIDGE_ETH
|
|
default 7
|
|
|
|
config BRIDGE_ETH_MISO_GPIO
|
|
int "MISO GPIO (XIAO D9)"
|
|
depends on BRIDGE_ETH
|
|
default 8
|
|
|
|
config BRIDGE_ETH_MOSI_GPIO
|
|
int "MOSI GPIO (XIAO D10)"
|
|
depends on BRIDGE_ETH
|
|
default 9
|
|
|
|
config BRIDGE_ETH_CS_GPIO
|
|
int "CS GPIO (XIAO D1)"
|
|
depends on BRIDGE_ETH
|
|
default 2
|
|
|
|
config BRIDGE_ETH_INT_GPIO
|
|
int "INT GPIO (XIAO D2), -1 to poll"
|
|
depends on BRIDGE_ETH
|
|
default 3
|
|
|
|
config BRIDGE_ETH_RST_GPIO
|
|
int "RST GPIO (XIAO D0), -1 if not wired"
|
|
depends on BRIDGE_ETH
|
|
default 1
|
|
|
|
endmenu
|
|
|
|
menu "Bridge microphone (I2S)"
|
|
|
|
config BRIDGE_MIC
|
|
bool "Stream an I2S microphone to the host"
|
|
default y if IDF_TARGET_ESP32S3
|
|
default n
|
|
help
|
|
The host (led-controller on the desktop) can record from an I2S mic on this board
|
|
(INMP441 wiring, as on the controller's XIAO ESP32-S3). Off on boards without one.
|
|
|
|
config BRIDGE_MIC_SCK_GPIO
|
|
int "I2S SCK (bit clock) GPIO"
|
|
depends on BRIDGE_MIC
|
|
default 5
|
|
|
|
config BRIDGE_MIC_WS_GPIO
|
|
int "I2S WS (word select) GPIO"
|
|
depends on BRIDGE_MIC
|
|
default 6
|
|
|
|
config BRIDGE_MIC_SD_GPIO
|
|
int "I2S SD (data) GPIO"
|
|
depends on BRIDGE_MIC
|
|
default 43
|
|
|
|
endmenu
|