112 lines
2.2 KiB
Plaintext
112 lines
2.2 KiB
Plaintext
$Id$
|
|
|
|
Approximate change log for AVRPROG by version
|
|
|
|
----------------------------------------------------------------------
|
|
|
|
Version 2.1.0:
|
|
|
|
* Implement a per-part erase-rewrite cycle counter; requires the use
|
|
of two bytes of EEPROM memory.
|
|
|
|
|
|
Version 2.0.5:
|
|
|
|
* Support for ATtiny15 - contributed by Asher Hoskins
|
|
|
|
|
|
Version 2.0.4:
|
|
|
|
* Config file fixes for various parts.
|
|
|
|
|
|
Version 2.0.3:
|
|
|
|
* Work around problem programming fuse bits on parts like the
|
|
at90s4433 as described in the following errata:
|
|
|
|
http://www.atmel.com/atmel/acrobat/doc1280.pdf
|
|
|
|
* Add part definition for at90s4414, at90s4433.
|
|
|
|
* Add fuse/lock bit memory instructions for the at90s1200,
|
|
at90s2333, at90s4433 and at90s8515.
|
|
|
|
* Fix setting of programmer status LEDs under certain write-fail
|
|
conditions.
|
|
|
|
|
|
Version 2.0.2 :
|
|
|
|
* Fix writing to read-only memories such as the lock bits of the
|
|
AT90S2313.
|
|
|
|
* Copyright updates.
|
|
|
|
|
|
Version 2.0.1 :
|
|
|
|
* Use correct parallel port pins for VCC.
|
|
|
|
* Add programmer definition for Atmel's STK200.
|
|
|
|
* Add programmer definition for the AVR3 board.
|
|
|
|
* Fix address bit encoding for many parts.
|
|
|
|
* Allow the ``BUFF'' signal to be asserted by multiple pins of the
|
|
parallel port (like VCC) instead of just one. The STK200 appears
|
|
to need this feature.
|
|
|
|
|
|
Version 2.0.0 :
|
|
|
|
* Add support for programming fuse and lock bits if supported by the
|
|
part.
|
|
|
|
* Move instruction encoding into the config file. Now any part can
|
|
be supported as long as it uses the same basic serial programming
|
|
instruction format.
|
|
|
|
* Add part definitions for the ATMega163 and ATMega8 devices.
|
|
|
|
|
|
Version 1.4.3 :
|
|
|
|
* Mostly internal code cleanup.
|
|
|
|
|
|
Version 1.4.2 :
|
|
|
|
* Fixes for ATMega paged memory support.
|
|
|
|
* Support for ATMega16 device.
|
|
|
|
|
|
Version 1.4.1 :
|
|
|
|
* No functional changes, update to Copyrights only.
|
|
|
|
|
|
Version 1.4.0 :
|
|
|
|
* Add part definitions to the config file.
|
|
|
|
* Add initial support for Atmel's ATMega paged memory parts.
|
|
|
|
* Config file documentation added.
|
|
|
|
* Add a definition for the Dontronics DT006 programmer.
|
|
|
|
* Fix Intel Hex support for addresses larger than 64k.
|
|
|
|
|
|
Version 1.3.0 :
|
|
|
|
* Make programmer pin assignments configurable.
|
|
|
|
|
|
Version 1.2.2 :
|
|
|
|
* Initial public release
|