avrdude/ChangeLog

64 lines
2.5 KiB
Plaintext

2013-01-30 Rene Liebscher <R.Liebscher@gmx.de>
patch #7936 Patch to support BusPirate AVR Extended Commands mode
* buspirate.c: added support for BusPirate AVR Extended Commands mode
* avrdude.1: added doc for nopagedread parameter
* doc/avrdude.texi: added doc for nopagedread parameter
2013-01-30 Rene Liebscher <R.Liebscher@gmx.de>
patch #7723 Bus Pirate “raw-wire” mode which can run down to 5 kHz
* buspirate.c: added raw wire mode
* avrdude.1: added doc for rawfreq parameter
* doc/avrdude.texi: added doc for rawfreq parameter
2013-01-30 Rene Liebscher <R.Liebscher@gmx.de>
bug #37977 Support for Openmoko Debug Board
* avrdude.conf.in: added openmoko entry
2013-01-29 Rene Liebscher <R.Liebscher@gmx.de>
patch #7932 Read USBtiny VID and PID from avrdude.conf if provided.
* avrdude.conf.in: added usbpid, usbvid to usbtiny
* usbtiny.[ch]: use usbpid, usbpid if provided in config file
2013-01-26 Joerg Wunsch <j.gnu@uriah.heep.sax.de>
bug #38172: avrftdi: Incorrect information in avrdude.conf
* avrdude.conf.in (avrftdi): fix comments about ACBUS vs. ADBUS;
add a comment that the MPSSE signals are fixed by the FTDI
hardware and cannot be changed
2013-01-09 Rene Liebscher <R.Liebscher@gmx.de>
patch #7165 Add support for bitbanging GPIO lines using the Linux sysf GPIO interface
* doc/avrdude.texi,avrdude.1: added doc for linuxgpio
* avrdude.conf.in: added template for linuxgpio programmer
* config_gram.y: pin numbers restricted to [PIN_MIN, PIN_MAX]
* pindefs.h: added PIN_MIN, PIN_MAX, removed unused LED_ON/OFF
* configure.ac: configure option enable-linuxgpio, print of enabled options
* linuxgpio.[ch]: new source for linuxgpio programmer
* Makefile.am: added linuxgpio to sources list
* pgm_type.c: added linuxgpio to programmer types list
2013-01-08 Joerg Wunsch <j.gnu@uriah.heep.sax.de>
* jtagmkI.c (jtagmkI_prmsg): replace a putchar() by putc(...stderr)
* jtagmkII.c (jtagmkII_prmsg): (Dito.)
* jtag3.c (jtag3_prevent, jtag3_prmsg): (Dito.)
2013-01-02 Joerg Wunsch <j.gnu@uriah.heep.sax.de>
* usb_libusb.c (usbdev_open): Downgrade the max transfer size for
the main data endpoints when being forced so by the USB; this can
happen when attaching the JTAGICE3 to a USB 1.1 connection
* jtag3.c (jtag3_initialize): When detecting a downgraded max
transfer size on the JTAGICE3 (presumably, due to being connected
to USB 1.1 only), bail out as its firmware cannot properly handle
this (by now)
2013-01-02 Joerg Wunsch <j.gnu@uriah.heep.sax.de>
* ChangeLog: annual ChangeLog rotation time