avr
/
avrdude
mirror of https://github.com/mariusgreuel/avrdude.git
2
0
Fork 0
Code Issues Projects Releases Wiki Activity
avrdude/avrdude/ChangeLog-2002

238 lines
7.3 KiB
Plaintext
Raw Blame History

2002-12-12 Brian S. Dean <bsd@bsdhome.com>
* main.c: minor cleanup
2002-12-07 Brian S. Dean <bsd@bsdhome.com>
* avrdude.1, main.c:
If the stk500 is being used, default to using the first serial port.
2002-12-03 Brian S. Dean <bsd@bsdhome.com>
* avrdude.1: Mention STK500 support.
2002-12-01 Brian S. Dean <bsd@bsdhome.com>
* stk500.c: Remove unused code.
* CHANGELOG, stk500.c:
Document changes since the previous version in the CHANGELOG.
Cleanup stk500.c a bit.
* stk500.c: Fix cut and paste braino.
* avr.c, avrdude.conf.sample, main.c, pgm.h, stk500.c:
The STK500 can perform paged read/write operations even on standard
"non-paged" parts. Take advantage of that and use the faster internal
routines of the STK500 for those parts as well.
* avr.c, avr.h, avrpart.h, main.c, pgm.c, pgm.h, stk500.c:
Optimize reading and writing for the STK500 programmer if the part
supports paged reads and writes. This greatly decreases the
program/verify time from about 4.5 minutes down to about 10 seconds in
a 12K program size test case.
Print out the hardware and firmware version for the STK500 if verbose
is enabled.
* avrdude.conf.sample, avrpart.h, config_gram.y, lexer.l, pgm.h:
* ppi.c, ppi.h, stk500.c, stk500.h, stk500_private.h:
Add basic support for STK500.
2002-11-30 Brian S. Dean <bsd@bsdhome.com>
* avrdude.conf.sample, config.c, config.h, config_gram.y, lexer.l:
* main.c, pgm.c, pgm.h, ppi.c, ppi.h, term.c, term.h, Makefile:
* avr.c, avr.h:
Seperate programmer operations out into a driver-like interface so
that programmers other than the direct parallel port connection can be
supported.
2002-11-23 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG, main.c, term.c:
term.c - when in interactive terminal mode and dumping memory using
the 'dump <memtype>' command without any address information,
and the end of memory is reached, wrap back around to zero on
the next invocation.
CHANGELOG - describe changes
main.c - update version number
* main.c:
When getting ready to initiate communications with the AVR device,
first pull /RESET low for a short period of time before enabling the
buffer chip. This sequence allows the AVR to be reset before the
buffer is enabled to avoid a short period of time where the AVR may be
driving the programming lines at the same time the programmer tries
to. Of course, if a buffer is being used, then the /RESET line from
the programmer needs to be directly connected to the AVR /RESET line
and not via the buffer chip.
2002-11-06 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG: Update changelog.
* avr.c, avr.h, main.c: Fix -Y option. Reported by Joerg Wunsch.
2002-11-01 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG, main.c: Version update and CHANGELOG entry.
* avr.c:
Be backward compatible with the 2-byte rewrite cycle counter which
appeared in version 2.1.0, but was changed to a 4 byte counter in
version 2.1.1. Reminded by Joerg Wunsch.
2002-10-29 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG, avrdude.1, main.c:
Add '-V' (no verify) flag requested by Joerg Wunsch. Update the man
page.
2002-10-13 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG, avrdude.1: Update man page and changelog.
* main.c: Update version number.
2002-10-12 Brian S. Dean <bsd@bsdhome.com>
* Makefile: Remove --pedantic and -g from the compiler options.
2002-10-11 Brian S. Dean <bsd@bsdhome.com>
* avr.c, term.c:
Use a four byte value instead of a two byte value for the programming
cycle count stored at the end of EEPROM. It seems as though Atmel was
greatly conservative in claiming a 1000 count reliability for the
FLASH. I current have a part that has been reprogrammed 173330 times,
and counting.
Fix a compiler warning.
* avrdude.conf.sample:
Fix ATMega128 instruction encoding for reading the low and high fuse
bits. Thanks to Joerg Wunsch for tripping over this.
2002-08-01 Brian S. Dean <bsd@bsdhome.com>
* avr.c, avrdude.1, main.c:
Move erase-rewrite cycle increment to within the chip erase routine so
that it is tracked no matter where the erase was initiated: command
line mode or interactive mode, without code duplicaiton.
* CHANGELOG: Recent updates.
* avr.c: Eliminate unused variables.
* avr.c, avr.h, avrdude.1, fileio.c, main.c:
Implement a way of tracking how many erase-rewrite cycles a part has
undergone. This utilizes the last two bytes of EEPROM to maintain a
counter that is incremented each time the part is erased.
2002-07-27 Brian S. Dean <bsd@bsdhome.com>
* avr.c, main.c:
Fix a typo in a comment. Display the size of memory being written.
Display the correct memory name in an error message (previously
hardcoded).
2002-06-22 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG, avrdude.conf.sample:
Add support for ATtiny15 - contributed by Asher Hoskins
<asher@crumbly.freeserve.co.uk>
2002-04-23 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG: Say what changed.
2002-04-07 Brian S. Dean <bsd@bsdhome.com>
* Makefile, avrdude.conf.sample:
Backup the config file to a timestamped name to keep from possibly
overwriting user-modified configs.
Add read/write instructions for all memory types for ATMEGA103,
ATMEGA128, ATMEGA16, and ATMEGA8.
2002-04-05 Brian S. Dean <bsd@bsdhome.com>
* avrdude.conf.sample:
Add support for ATMEGA128; untested; requested by Jeff Gardner
<gardner@journey.com>.
2002-02-15 Brian S. Dean <bsd@bsdhome.com>
* avrdude.conf.sample: Minor ordering.
* CHANGELOG, main.c: Update version numbers.
2002-02-14 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG: Summarize latest updates.
* avrdude.conf.sample, config_gram.y:
Make pwroff_after_write a yes/no field instead of a numeric.
* avrdude.conf.sample: Document the pwroff_after_write flag.
* avr.c: Enable the extra part verbosity when verbosity >= 3.
* avr.c, avr.h, avrdude.conf.sample, config_gram.y, lexer.l:
* main.c, term.c:
Fix error reporting by avr_write_byte().
Fix setting of status LEDs under various write-fail conditions.
Add a flag to indicate that a memory type requires the device to
possibly be powered off and back on after a write to it. This is due
to a hardware problem on some Atmel devices, see:
http://www.atmel.com/atmel/acrobat/doc1280.pdf
Add greater verbosity to the part-display code when verbose>1 to
display avrprog's encoding of the defined programming instructions.
This is primarily for debugging purposes.
Part updates:
* add the AT90S4414 part
* add fuse and lock bit access instructions for the AT90S1200,
AT90S4434, and AT90S8515.
* add the pwroff_after_write flag to the fuse bits for the AT90S2333
and AT90S4433 parts
2002-02-09 Brian S. Dean <bsd@bsdhome.com>
* avrdude.conf.sample:
Updates to the 2333 and 4433 parts, contributed by Joerg Wunsh.
2002-01-18 Brian S. Dean <bsd@bsdhome.com>
* CHANGELOG: Add changelog.
2002-01-12 Brian S. Dean <bsd@bsdhome.com>
* main.c: Add (c) to copyright.
* fileio.c, fileio.h, lexer.l, lists.c, lists.h, main.c:
* pindefs.h, ppi.c, ppi.h, term.c, term.h, avr.c, avr.h:
* config.c, config.h, config_gram.y:
Update version number. Update copyright.
* avrdude.1: Update copyright and add description of "default".
Submitted by: Joerg Wunsch <j@uriah.heep.sax.de>
* avr.c, term.c:
Fix programming of write-only memories (such as lock bits on the
2313).
Reference in New Issue View Git Blame Copy Permalink