# $Id$ -*- text -*- # # AVRDUDE Configuration File # # This file contains configuration data used by AVRDUDE which describes # the programming hardware pinouts and also provides part definitions. # AVRDUDE's "-C" command line option specifies the location of the # configuration file. The "-c" option names the programmer configuration # which must match one of the entry's "id" parameter. The "-p" option # identifies which part AVRDUDE is going to be programming and must match # one of the parts' "id" parameter. # # DO NOT MODIFY THIS FILE. Modifications will be overwritten the next # time a "make install" is run. For user-specific additions, use the # "-C +filename" command line option. # # Possible entry formats are: # # programmer # parent # optional parent # id = [, ... ] ; # are quoted strings # desc = ; # quoted string # type = ; # programmer type, quoted string # # supported types can be listed by "-c ?type" # prog_modes = PM_ {| PM_} # interfaces, eg, PM_SPM|PM_PDI (1) # connection_type = parallel | serial | usb | spi # baudrate = ; # baudrate for avr910-programmer # vcc = [, ... ] ; # pin number(s) # buff = [, ... ] ; # pin number(s) # reset = ; # pin number # sck = ; # pin number # mosi = ; # pin number # miso = ; # pin number # errled = ; # pin number # rdyled = ; # pin number # pgmled = ; # pin number # vfyled = ; # pin number # usbvid = ; # USB VID (Vendor ID) # usbpid = [, ...] ; # USB PID (Product ID) (2) # usbdev = ; # USB interface or other device info # usbvendor = ; # USB Vendor Name # usbproduct = ; # USB Product Name # usbsn = ; # USB Serial Number # hvupdi_support = [, , ... ] ; # UPDI HV Variants Support # ; # # # To invert a pin use = ~ # # To invert a pin list (all pins get inverted) use ~ ( [, ... ] ) # # # # (1) The following program modes are known: # # - PM_SPM: Bootloaders, self-programming with SPM opcodes or NVM Controllers # # - PM_TPI: Tiny Programming Interface (t4, t5, t9, t10, t20, t40, t102, t104) # # - PM_ISP: SPI programming for In-System Programming (almost all classic parts) # # - PM_PDI: Program and Debug Interface (xmega parts) # # - PM_UPDI: Unified Program and Debug Interface # # - PM_HVSP: High Voltage Serial Programming (some classic parts) # # - PM_HVPP: High Voltage Parallel Programming (most non-HVSP classic parts) # # - PM_debugWIRE: Simpler alternative to JTAG (a subset of HVPP/HVSP parts) # # - PM_JTAG: Joint Test Action Group standard (some classic parts) # # - PM_JTAGmkI: Subset of PM_JTAG, older parts, Atmel ICE mkI # # - PM_XMEGAJTAG: JTAG, some XMEGA parts # # - PM_AVR32JTAG: JTAG for 32-bit AVRs # # - PM_aWire: AVR32 parts # # # # (2) Not all programmer types can process a list of PIDs # # part # desc = ; # quoted string # id = ; # quoted string # family_id = ; # quoted string, eg, "megaAVR" or "tinyAVR" # prog_modes = PM_ {| PM_} # interfaces, eg, PM_SPM|PM_ISP|PM_HVPP|PM_debugWIRE # mcuid = ; # unique id in 0..2039 for 8-bit AVRs # n_interrupts = ; # number of interrupts, used for vector bootloaders # n_page_erase = ; # if set, number of pages erased during NVM erase # hvupdi_variant = ; # numeric -1 (n/a) or 0..2 # devicecode = ; # deprecated, use stk500_devcode # stk500_devcode = ; # numeric # avr910_devcode = ; # numeric # has_jtag = ; # part has JTAG i/f (deprecated, use prog_modes) # has_debugwire = ; # part has debugWire i/f (deprecated, use prog_modes) # has_pdi = ; # part has PDI i/f (deprecated, use prog_modes) # has_updi = ; # part has UPDI i/f (deprecated, use prog_modes) # has_tpi = ; # part has TPI i/f (deprecated, use prog_modes) # is_avr32 = ; # AVR32 part (deprecated, use prog_modes) # is_at90s1200 = ; # AT90S1200 part # signature = ; # signature bytes # usbpid = ; # DFU USB PID # chip_erase_delay = ; # micro-seconds # reset = dedicated | io ; # retry_pulse = reset | sck ; # chip_erase_delay = ; # chip erase delay (us) # # STK500 parameters (parallel programming IO lines) # pagel = ; # pin name in hex, i.e., 0xD7 # bs2 = ; # pin name in hex, i.e., 0xA0 # serial = ; # can use serial downloading # parallel = ; # can use par. programming # # STK500v2 parameters, to be taken from Atmel's ATDF files # timeout = ; # stabdelay = ; # cmdexedelay = ; # synchloops = ; # bytedelay = ; # pollvalue = ; # pollindex = ; # predelay = ; # postdelay = ; # pollmethod = ; # hvspcmdexedelay = ; # # STK500v2 HV programming parameters, from ATDFs # pp_controlstack = , , ... ; # PP only # hvsp_controlstack = , , ... ; # HVSP only # flash_instr = , , ; # eeprom_instr = , , ... ; # hventerstabdelay = ; # progmodedelay = ; # PP only # latchcycles = ; # togglevtg = ; # poweroffdelay = ; # resetdelayms = ; # resetdelayus = ; # hvleavestabdelay = ; # resetdelay = ; # synchcycles = ; # HVSP only # chiperasepulsewidth = ; # PP only # chiperasepolltimeout = ; # chiperasetime = ; # HVSP only # programfusepulsewidth = ; # PP only # programfusepolltimeout = ; # programlockpulsewidth = ; # PP only # programlockpolltimeout = ; # # JTAG ICE mkII parameters, also from ATDF files # allowfullpagebitstream = ; # enablepageprogramming = ; # idr = ; # IO addr of IDR (OCD) reg # rampz = ; # IO addr of RAMPZ reg # spmcr = ; # mem addr of SPMC[S]R reg # eecr = ; # mem addr of EECR reg only when != 0x3f # mcu_base = ; # nvm_base = ; # ocd_base = ; # ocdrev = ; # pgm_enable = ; # chip_erase = ; # # memory # paged = ; # yes/no (flash only, do not use for EEPROM) # offset = ; # memory offset # size = ; # bytes # page_size = ; # bytes # num_pages = ; # numeric # min_write_delay = ; # micro-seconds # max_write_delay = ; # micro-seconds # readback = ; # pair of byte values # readback_p1 = ; # byte value (first component) # readback_p2 = ; # byte value (second component) # pwroff_after_write = ; # yes/no # mode = ; # STK500 v2 file parameter from ATDF files # delay = ; # " # blocksize = ; # " # readsize = ; # " # read = ; # write = ; # read_lo = ; # read_hi = ; # write_lo = ; # write_hi = ; # loadpage_lo = ; # loadpage_hi = ; # writepage = ; # ; # ; # # If any of the above parameters are not specified, the default value # of 0 is used for numerics (except for mcuid, hvupdi_variant and # ocdrev, where the default value is -1) or the empty string "" for # string values. If a required parameter is left empty, AVRDUDE will # complain. Almost all occurrences of numbers (with the exception of # pin numbers and where they are separated by space, eg, in signature # and readback) can also be given as simple expressions involving # arithemtic and bitwise operators. # # Parts can also inherit parameters from previously defined parts # using the following syntax. In this case specified integer and # string values override parameter values from the parent part. New # memory definitions are added to the definitions inherited from the # parent. If, however, a new memory definition refers to an existing # one of the same name for that part then, from v7.1, the existing # memory definition is extended, and components overwritten with new # values. Assigning NULL removes an inherited SPI instruction format, # memory definition, control stack, eeprom or flash instruction, eg, # as in memory "efuse" = NULL; # # part parent # quoted string # id = ; # quoted string # # ; # # NOTES: # * 'devicecode' is the device code used by the STK500 (see codes # listed below) # * Not all memory types will implement all instructions # * AVR Fuse bits and Lock bits are implemented as a type of memory # * Example memory types are: # "flash", "eeprom", "fuse", "lfuse" (low fuse), "hfuse" (high # fuse), "signature", "calibration", "lock" # * The memory type specified on the avrdude command line must match # one of the memory types defined for the specified chip # * The pwroff_after_write flag causes avrdude to attempt to # power the device off and back on after an unsuccessful write to # the affected memory area if VCC programmer pins are defined. If # VCC pins are not defined for the programmer, a message # indicating that the device needs a power-cycle is printed out. # This flag was added to work around a problem with the # at90s4433/2333's; see the at90s4433 errata at: # # http://www.atmel.com/dyn/resources/prod_documents/doc1280.pdf # # INSTRUCTION FORMATS # # Instruction formats are specified as a comma separated list of # string values containing information (bit specifiers) about each # of the 32 bits of the instruction. Bit specifiers may be one of # the following formats: # # '1' = the bit is always set on input as well as output # # '0' = the bit is always clear on input as well as output # # 'x' = the bit is ignored on input and output and set as 0 # # 'a' = the bit is an address bit; from v 7.1 the bit-number # is set to match the right bit position for the # instruction to "just work" # # 'aN' = the bit is the Nth address bit, bit-number = N, i.e., a12 # is address bit 12 on input, a0 is address bit 0. # # 'i' = the bit is an input data bit # # 'o' = the bit is an output data bit # # Each instruction must be composed of 32 bit specifiers. The # instruction specification closely follows the instruction data # provided in Atmel's data sheets for their parts. Note that flash # addresses always refer to *word* addresses whilst all other # memory types specify *byte* addresses. # # Example for signature read on the ATmega328P: # read = "0 0 1 1 0 0 0 0", "0 0 0 x x x x x", # "x x x x x x a1 a0", "o o o o o o o o"; # # As the address bit numbers in the SPI opcodes are highly # systematic, they don't really need to be specified. A compact # version of the format specification neither uses bit-numbers for # address lines nor spaces. If such a string is longer than 7 # characters, then the characters 0, 1, x, a, i and o will be # recognised as the corresponding bit, whilst any of the characters # ., -, _ or / can act as arbitrary visual separators, which are # ignored. Examples: # # loadpage_lo = "0100.0000--000x.xxxx--xxaa.aaaa--iiii.iiii"; # # loadpage_lo = "0100.0000", "000x.xxxx", "xxaa.aaaa", "iiii.iiii"; # # # The following are STK500 part device codes to use for the # "devicecode" field of the part. These came from Atmel's software # section avr061.zip which accompanies the application note # AVR061 available from: # # https://ww1.microchip.com/downloads/en/Appnotes/doc2525.pdf # #define ATTINY10 0x10 /* the _old_ one that never existed! */ #define ATTINY11 0x11 #define ATTINY12 0x12 #define ATTINY15 0x13 #define ATTINY13 0x14 #define ATTINY22 0x20 #define ATTINY26 0x21 #define ATTINY28 0x22 #define ATTINY2313 0x23 #define AT90S1200 0x33 #define AT90S2313 0x40 #define AT90S2323 0x41 #define AT90S2333 0x42 #define AT90S2343 0x43 #define AT90S4414 0x50 #define AT90S4433 0x51 #define AT90S4434 0x52 #define ATMEGA48 0x59 #define AT90S8515 0x60 #define AT90S8535 0x61 #define AT90C8534 0x62 #define ATMEGA8515 0x63 #define ATMEGA8535 0x64 #define ATMEGA8 0x70 #define ATMEGA88 0x73 #define ATMEGA168 0x86 #define ATMEGA161 0x80 #define ATMEGA163 0x81 #define ATMEGA16 0x82 #define ATMEGA162 0x83 #define ATMEGA169 0x84 #define ATMEGA323 0x90 #define ATMEGA32 0x91 #define ATMEGA64 0xA0 #define ATMEGA103 0xB1 #define ATMEGA128 0xB2 #define AT90CAN128 0xB3 #define AT90CAN64 0xB3 #define AT90CAN32 0xB3 #define AT86RF401 0xD0 #define AT89START 0xE0 #define AT89S51 0xE0 #define AT89S52 0xE1 # The following table lists the devices in the original AVR910 # appnote: # |Device |Signature | Code | # +-------+----------+------+ # |tiny12 | 1E 90 05 | 0x55 | # |tiny15 | 1E 90 06 | 0x56 | # | | | | # | S1200 | 1E 90 01 | 0x13 | # | | | | # | S2313 | 1E 91 01 | 0x20 | # | S2323 | 1E 91 02 | 0x48 | # | S2333 | 1E 91 05 | 0x34 | # | S2343 | 1E 91 03 | 0x4C | # | | | | # | S4414 | 1E 92 01 | 0x28 | # | S4433 | 1E 92 03 | 0x30 | # | S4434 | 1E 92 02 | 0x6C | # | | | | # | S8515 | 1E 93 01 | 0x38 | # | S8535 | 1E 93 03 | 0x68 | # | | | | # |mega32 | 1E 95 01 | 0x72 | # |mega83 | 1E 93 05 | 0x65 | # |mega103| 1E 97 01 | 0x41 | # |mega161| 1E 94 01 | 0x60 | # |mega163| 1E 94 02 | 0x64 | # Appnote AVR109 also has a table of AVR910 device codes, which # lists: # dev avr910 signature # ATmega8 0x77 0x1E 0x93 0x07 # ATmega8515 0x3B 0x1E 0x93 0x06 # ATmega8535 0x6A 0x1E 0x93 0x08 # ATmega16 0x75 0x1E 0x94 0x03 # ATmega162 0x63 0x1E 0x94 0x04 # ATmega163 0x66 0x1E 0x94 0x02 # ATmega169 0x79 0x1E 0x94 0x05 # ATmega32 0x7F 0x1E 0x95 0x02 # ATmega323 0x73 0x1E 0x95 0x01 # ATmega64 0x46 0x1E 0x96 0x02 # ATmega128 0x44 0x1E 0x97 0x02 # # These codes refer to "BOOT" device codes which are apparently # different than standard device codes, for whatever reasons # (often one above the standard code). # There are several extended versions of AVR910 implementations around # in the Internet. These add the following codes (only devices that # actually exist are listed): # ATmega8515 0x3A # ATmega128 0x43 # ATmega64 0x45 # ATtiny26 0x5E # ATmega8535 0x69 # ATmega32 0x72 # ATmega16 0x74 # ATmega8 0x76 # ATmega169 0x78 # # Overall avrdude defaults; suitable for ~/.avrduderc # default_parallel = "@DEFAULT_PAR_PORT@"; default_serial = "@DEFAULT_SER_PORT@"; default_spi = "@DEFAULT_SPI_PORT@"; # default_bitclock = 2.5; @HAVE_PARPORT_BEGIN@ # Parallel port programmers #------------------------------------------------------------ # bsd #------------------------------------------------------------ programmer id = "bsd"; desc = "Brian Dean's Programmer, http://www.bsdhome.com/avrdude/"; type = "par"; prog_modes = PM_TPI | PM_ISP; vcc = 2, 3, 4, 5; reset = 7; sck = 8; mosi = 9; miso = 10; ; #------------------------------------------------------------ # stk200 #------------------------------------------------------------ programmer id = "stk200"; desc = "STK200"; type = "par"; prog_modes = PM_TPI | PM_ISP; buff = 4, 5; reset = 9; sck = 6; mosi = 7; miso = 10; ; #------------------------------------------------------------ # pony-stk200 #------------------------------------------------------------ # The programming dongle used by the popular Ponyprog # utility. It is almost similar to the STK200 one, # except that there is a LED indicating that the # programming is currently in progress. programmer parent "stk200" id = "pony-stk200"; desc = "Pony Prog STK200"; pgmled = 8; ; #------------------------------------------------------------ # dt006 #------------------------------------------------------------ programmer id = "dt006"; desc = "Dontronics DT006"; type = "par"; prog_modes = PM_TPI | PM_ISP; reset = 4; sck = 5; mosi = 2; miso = 11; ; #------------------------------------------------------------ # bascom #------------------------------------------------------------ programmer parent "dt006" id = "bascom"; desc = "Bascom SAMPLE programming cable"; ; #------------------------------------------------------------ # alf #------------------------------------------------------------ programmer id = "alf"; desc = "Nightshade ALF-PgmAVR, http://nightshade.homeip.net/"; type = "par"; prog_modes = PM_TPI | PM_ISP; vcc = 2, 3, 4, 5; buff = 6; reset = 7; sck = 8; mosi = 9; miso = 10; errled = 1; rdyled = 14; pgmled = 16; vfyled = 17; ; #------------------------------------------------------------ # sp12 #------------------------------------------------------------ programmer id = "sp12"; desc = "Steve Bolt's Programmer"; type = "par"; prog_modes = PM_TPI | PM_ISP; vcc = 4, 5, 6, 7, 8; reset = 3; sck = 2; mosi = 9; miso = 11; ; #------------------------------------------------------------ # picoweb #------------------------------------------------------------ programmer id = "picoweb"; desc = "Picoweb Programming Cable, http://www.picoweb.net/"; type = "par"; prog_modes = PM_TPI | PM_ISP; reset = 2; sck = 3; mosi = 4; miso = 13; ; #------------------------------------------------------------ # abcmini #------------------------------------------------------------ programmer id = "abcmini"; desc = "ABCmini Board, aka Dick Smith HOTCHIP"; type = "par"; prog_modes = PM_TPI | PM_ISP; reset = 4; sck = 3; mosi = 2; miso = 10; ; #------------------------------------------------------------ # futurlec #------------------------------------------------------------ programmer id = "futurlec"; desc = "Futurlec.com programming cable."; type = "par"; prog_modes = PM_TPI | PM_ISP; reset = 3; sck = 2; mosi = 1; miso = 10; ; #------------------------------------------------------------ # xil #------------------------------------------------------------ # From the contributor of the "xil" jtag cable: # The "vcc" definition isn't really vcc (the cable gets its power from # the programming circuit) but is necessary to switch one of the # buffer lines (trying to add it to the "buff" lines doesn't work in # avrdude versions before 5.5j). # With this, TMS connects to RESET, TDI to MOSI, TDO to MISO and TCK # to SCK (plus vcc/gnd of course) programmer id = "xil"; desc = "Xilinx JTAG cable"; type = "par"; prog_modes = PM_TPI | PM_ISP; vcc = 6; buff = 5; reset = 4; sck = 3; mosi = 2; miso = 13; ; #------------------------------------------------------------ # dapa #------------------------------------------------------------ programmer id = "dapa"; desc = "Direct AVR Parallel Access cable"; type = "par"; prog_modes = PM_TPI | PM_ISP; vcc = 3; reset = 16; sck = 1; mosi = 2; miso = 11; ; #------------------------------------------------------------ # atisp #------------------------------------------------------------ programmer id = "atisp"; desc = "AT-ISP v1.1 programming cable for AVR-SDK1 from "; type = "par"; prog_modes = PM_TPI | PM_ISP; reset = ~6; sck = ~8; mosi = ~7; miso = ~10; ; #------------------------------------------------------------ # ere-isp-avr #------------------------------------------------------------ programmer id = "ere-isp-avr"; desc = "ERE ISP-AVR "; type = "par"; prog_modes = PM_TPI | PM_ISP; reset = ~4; sck = 3; mosi = 2; miso = 10; ; #------------------------------------------------------------ # blaster #------------------------------------------------------------ programmer id = "blaster"; desc = "Altera ByteBlaster"; type = "par"; prog_modes = PM_TPI | PM_ISP; buff = 14; reset = 3; sck = 2; mosi = 8; miso = 11; ; #------------------------------------------------------------ # frank-stk200 #------------------------------------------------------------ # It is almost same as pony-stk200, except vcc on pin 5 to auto # disconnect port (download on http://electropol.free.fr/spip/spip.php?article27) programmer parent "pony-stk200" id = "frank-stk200"; desc = "Frank STK200"; vcc = 5; buff = ; # delete buff pin assignment ; #------------------------------------------------------------ # 89isp #------------------------------------------------------------ # The AT98ISP Cable is a simple parallel dongle for AT89 family. # http://www.atmel.com/dyn/products/tools_card.asp?tool_id=2877 programmer id = "89isp"; desc = "Atmel at89isp cable"; type = "par"; prog_modes = PM_TPI | PM_ISP; reset = 17; sck = 1; mosi = 2; miso = 10; ; @HAVE_PARPORT_END@ @HAVE_LINUXGPIO_BEGIN@ # This programmer bitbangs GPIO lines using the Linux sysfs GPIO interface # # To enable it set the configuration below to match the GPIO lines connected # to the relevant ISP header pins and uncomment the entry definition. In case # you don't have the required permissions to edit this system wide config # file put the entry in a separate .conf file and use it with # -C+.conf on the command line. # # To check if your avrdude build has support for the linuxgpio programmer # compiled in, use -c?type on the command line and look for linuxgpio in the # list. If it's not available you need pass the --enable-linuxgpio=yes option # to configure and recompile avrdude. # # # #------------------------------------------------------------ # # linuxgpio # #------------------------------------------------------------ # # programmer # id = "linuxgpio"; # desc = "Use the Linux sysfs interface to bitbang GPIO lines"; # type = "linuxgpio"; # prog_modes = PM_ISP; # reset = ?; # sck = ?; # mosi = ?; # miso = ?; # ; @HAVE_LINUXGPIO_END@ @HAVE_LINUXSPI_BEGIN@ #------------------------------------------------------------ # linuxspi #------------------------------------------------------------ # This programmer uses the built in linux SPI bus devices to program an # attached AVR. The reset pin must be attached to a GPIO pin that # is otherwise unused (see gpioinfo(1)); the SPI bus CE pins are not # suitable since they would release /RESET too early. # programmer id = "linuxspi"; desc = "Use Linux SPI device in /dev/spidev*"; type = "linuxspi"; prog_modes = PM_TPI | PM_ISP; connection_type = spi; reset = 25; # Pi GPIO number - this is J8:22 ; @HAVE_LINUXSPI_END@ # # PROGRAMMER DEFINITIONS # #------------------------------------------------------------ # wiring #------------------------------------------------------------ # http://wiring.org.co/ # Basically STK500v2 protocol, with some glue to trigger the bootloader programmer id = "wiring"; desc = "Wiring for bootloader using STK500 v2 protocol"; type = "wiring"; prog_modes = PM_SPM; connection_type = serial; ; #------------------------------------------------------------ # arduino #------------------------------------------------------------ programmer id = "arduino"; desc = "Arduino for bootloader using STK500 v1 protocol"; type = "arduino"; prog_modes = PM_SPM; connection_type = serial; ; #------------------------------------------------------------ # xbee #------------------------------------------------------------ programmer id = "xbee"; desc = "XBee for Series 2 Over-The-Air (XBeeBoot) bootloader using STK500 v1 protocol"; type = "xbee"; prog_modes = PM_SPM; connection_type = serial; ; #------------------------------------------------------------ # avrftdi #------------------------------------------------------------ # this will interface with the chips on these programmers: # # http://real.kiev.ua/old/avreal/en/adapters # http://www.amontec.com/jtagkey.shtml, jtagkey-tiny.shtml # http://www.olimex.com/dev/arm-usb-ocd.html, arm-usb-tiny.html # http://www.ethernut.de/en/hardware/turtelizer/index.html # http://elk.informatik.fh-augsburg.de/hhweb/doc/openocd/usbjtag/usbjtag.html # http://dangerousprototypes.com/docs/FT2232_breakout_board # http://www.ftdichip.com/Products/Modules/DLPModules.htm,DLP-2232*,DLP-USB1232H # http://flashrom.org/FT2232SPI_Programmer # # The drivers will look for a specific device and use the first one found. # If you have mulitple devices, then look for unique information (like SN) # And fill that in here. # # Note that the pin numbers for the main ISP signals (reset, sck, # mosi, miso) are fixed and cannot be changed, since they must match # the way the Multi-Protocol Synchronous Serial Engine (MPSSE) of # these FTDI ICs has been designed. programmer id = "avrftdi"; desc = "FT2232D based generic programmer"; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x0403; usbpid = 0x6010; usbdev = "A"; # ISP-signals - lower ADBUS-Nibble (default) reset = 3; sck = 0; mosi = 1; miso = 2; # LED SIGNALs - higher ADBUS-Nibble # errled = 4; # rdyled = 5; # pgmled = 6; # vfyled = 7; # Buffer Signal - ACBUS - Nibble # buff = 8; ; #------------------------------------------------------------ # 2232HIO #------------------------------------------------------------ # This is an implementation of the above with a buffer IC (74AC244) and # 4 LEDs directly attached, all active low. programmer id = "2232HIO"; desc = "FT2232H based generic programmer"; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x0403; # Note: This PID is reserved for generic H devices and # should be programmed into the EEPROM # usbpid = 0x8A48; usbpid = 0x6010; usbdev = "A"; buff = ~4; #ISP-signals reset = 3; sck = 0; mosi = 1; miso = 2; #LED SIGNALs errled = ~11; rdyled = ~14; pgmled = ~13; vfyled = ~12; ; #------------------------------------------------------------ # 4232h #------------------------------------------------------------ #The FT4232H can be treated as FT2232H, but it has a different USB #device ID of 0x6011. programmer parent "avrftdi" id = "4232h"; desc = "FT4232H based generic programmer"; usbpid = 0x6011; ; #------------------------------------------------------------ # jtagkey #------------------------------------------------------------ programmer id = "jtagkey"; desc = "Amontec JTAGKey, JTAGKey-Tiny and JTAGKey2"; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x0403; # Note: This PID is used in all JTAGKey variants usbpid = 0xcff8; usbdev = "A"; buff = ~4; # ISP-signals => 20 - Pin connector on JTAGKey reset = 3; # TMS 7 violet sck = 0; # TCK 9 white mosi = 1; # TDI 5 green miso = 2; # TDO 13 orange # VTG VREF 1 brown with red tip # GND GND 20 black # The colors are on the 20 pin breakout cable from Amontec ; #------------------------------------------------------------ # ft232h #------------------------------------------------------------ programmer id = "ft232h"; desc = "FT232H in MPSSE mode"; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x0403; usbpid = 0x6014; usbdev = "A"; #ISP-signals reset = 3; # AD3 (TMS) sck = 0; # AD0 (TCK) mosi = 1; # AD1 (TDI) miso = 2; # AD2 (TDO) ; #------------------------------------------------------------ # um232h #------------------------------------------------------------ # Pin J2-7 (AD0) is SCK # Pin J2-8 (AD1) is MOSI # Pin J2-9 (AD2) is MISO # Pin J2-10 (AD3) is RESET # Pin J2-6 is GND # Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get # a 16MHz Atmega1280 to program reliably. The 232H is conveniently 5V tolerant. programmer parent "ft232h" id = "um232h"; desc = "UM232H module from FTDI"; usbpid = 0x6014; ; #------------------------------------------------------------ # c232hm #------------------------------------------------------------ # Orange (Pin 2) is SCK # Yellow (Pin 3) is MOSI # Green (Pin 4) is MISO # Brown (Pin 5) is RESET # Black (Pin 10) is GND # Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get # a 16MHz Atmega1280 to program reliably. The 232H is conveniently 5V tolerant. programmer parent "ft232h" id = "c232hm"; desc = "C232HM cable from FTDI"; usbpid = 0x6014; ; #------------------------------------------------------------ # o-link #------------------------------------------------------------ # On the adapter you can read "O-Link". On the PCB is printed "OpenJTAG v3.1" # You can find it as "OpenJTAG ARM JTAG USB" in the internet. # (But there are also several projects called Open JTAG, eg. # http://www.openjtag.org, which are completely different.) # http://www.100ask.net/shop/english.html (website seems to be outdated) # http://item.taobao.com/item.htm?id=1559277013 # http://www.micro4you.com/store/openjtag-arm-jtag-usb.html (schematics!) # some other sources which call it O-Link # http://www.andahammer.com/olink/ # http://www.developmentboard.net/31-o-link-debugger.html # http://armwerks.com/catalog/o-link-debugger-copy/ # or just have a look at ebay ... # It is basically the same entry as jtagkey with different usb ids. programmer parent "jtagkey" id = "o-link"; desc = "O-Link, OpenJTAG from www.100ask.net"; usbvid = 0x1457; usbpid = 0x5118; usbvendor = "www.100ask.net"; usbproduct = "USB<=>JTAG&RS232"; ; #------------------------------------------------------------ # openmoko #------------------------------------------------------------ # http://wiki.openmoko.org/wiki/Debug_Board_v3 programmer id = "openmoko"; desc = "Openmoko debug board (v3)"; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; usbvid = 0x1457; usbpid = 0x5118; usbdev = "A"; reset = 3; # TMS 7 sck = 0; # TCK 9 mosi = 1; # TDI 5 miso = 2; # TDO 13 ; #------------------------------------------------------------ # lm3s811 #------------------------------------------------------------ # Only Rev. A boards. # Schematic and user manual: http://www.cs.put.poznan.pl/wswitala/download/pdf/811EVBK.pdf programmer id = "lm3s811"; desc = "Luminary Micro LM3S811 Eval Board (Rev. A)"; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x0403; usbpid = 0xbcd9; usbdev = "A"; usbvendor = "LMI"; usbproduct = "LM3S811 Evaluation Board"; # Enable correct buffers buff = 7; #ISP-signals - lower ACBUS-Nibble (default) reset = 3; sck = 0; mosi = 1; miso = 2; ; #------------------------------------------------------------ # tumpa #------------------------------------------------------------ # submitted as bug #46020 programmer id = "tumpa"; desc = "TIAO USB Multi-Protocol Adapter"; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x0403; usbpid = 0x8a98; usbdev = "A"; usbvendor = "TIAO"; reset = 3; # TMS 7 sck = 0; # TCK 9 mosi = 1; # TDI 5 miso = 2; # TDO 13 ; #------------------------------------------------------------ # ktlink #------------------------------------------------------------ # Kristech KT-LINK FT2232H interface with IO switching and voltage buffers. # Created on 20220410 by CeDeROM Tomasz CEDRO (www.cederom.io). # Interface DataSheet: https://kristech.pl/files/KT-LINK-UM-ENG.pdf # AVRDUDE FT2232H PIN NUMBER DECODE: # | 0 | 1 | .. | 7 | 8 | 9 | .. | 15 | # | ADBUS0 | ADBUS1 | .. | ADBUS7 | ACBUS0 | ACBUS1 | .. | ACBUS7 | # KT-LINK JTAG CONN: # 1=Vsense(->EXT13), 19=5V(EXT1->EXT3), 20=GND, 3=TPIRST, 9=TPICLK, 7=TPIDATA. # INTERNALS CONFIGURATION ("~" MEANS ACTIVE LOW): # ~TRST_EN=10(ACBUS2), ~CLK_EN=14(ACBUS6), ~MOSI_EN=13(ACBUS5), # TMS_SEL=5(ADBUS5), ~TMS_EN=12(ACBUS4), LED=~15(ACBUS7). # CONNECTION NOTES: # * Connect EXT connector pin 1 with 3 to get 5V on JTAG connector pin 19. # * Connect JTAG connector pin 1 to 5V (i.e. EXT pin 13 or JTAG pin 19). # * For TPI connection use resistors: TDO --[470R]-- TPIDATA --[470R]-- TDI. # * Powering target from JTAG pin 19 allows KT-LINK current measurement. programmer id = "ktlink"; desc = "KT-LINK FT2232H interface with IO switching and voltage buffers."; type = "avrftdi"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x0403; usbpid = 0xbbe2; usbdev = "A"; buff = 5, ~10, ~13, ~14; reset = 8; sck = 0; mosi = 1; miso = 2; rdyled = ~15; ; #------------------------------------------------------------ # digilent-hs2 #------------------------------------------------------------ # Digilent JTAG HS2 programmer. FT232H-based dongle with buffers. # https://digilent.com/reference/_media/reference/programmers/jtag-hs2/jtag-hs2_rm.pdf programmer id = "digilent-hs2"; desc = "Digilient JTAG HS2 (MPSSE)"; type = "avrftdi"; connection_type = usb; usbvid = 0x0403; usbpid = 0x6014; usbdev = "A"; buff = 5, 6, 7; reset = 3; sck = 0; mosi = 1; miso = 2; ; #------------------------------------------------------------ # serialupdi #------------------------------------------------------------ programmer id = "serialupdi"; desc = "SerialUPDI"; type = "serialupdi"; prog_modes = PM_UPDI; connection_type = serial; hvupdi_support = 1; ; #------------------------------------------------------------ # avrisp #------------------------------------------------------------ programmer id = "avrisp"; desc = "Atmel AVR ISP"; type = "stk500"; prog_modes = PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # avrispv2 #------------------------------------------------------------ programmer id = "avrispv2"; desc = "Atmel AVR ISP v2"; type = "stk500v2"; prog_modes = PM_TPI | PM_ISP | PM_PDI; connection_type = serial; ; #------------------------------------------------------------ # avrispmkII #------------------------------------------------------------ programmer id = "avrispmkII"; desc = "Atmel AVR ISP mkII"; type = "stk500v2"; prog_modes = PM_TPI | PM_ISP | PM_PDI; connection_type = usb; ; #------------------------------------------------------------ # avrisp2 #------------------------------------------------------------ programmer parent "avrispmkII" id = "avrisp2"; ; #------------------------------------------------------------ # buspirate #------------------------------------------------------------ programmer id = "buspirate"; desc = "The Bus Pirate"; type = "buspirate"; prog_modes = PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # buspirate_bb #------------------------------------------------------------ programmer id = "buspirate_bb"; desc = "The Bus Pirate (bitbang interface, supports TPI)"; type = "buspirate_bb"; prog_modes = PM_TPI | PM_ISP; connection_type = serial; # pins are bits in bitbang byte (numbers are 87654321) # 1|POWER|PULLUP|AUX|MOSI|CLK|MISO|CS reset = 1; sck = 3; mosi = 4; miso = 2; # vcc = 7; # Internally set independent of this setting ; #------------------------------------------------------------ # stk500 #------------------------------------------------------------ # This is supposed to be the "default" STK500 entry. # Attempts to select the correct firmware version # by probing for it. Better use one of the entries # below instead. programmer id = "stk500"; desc = "Atmel STK500"; type = "stk500generic"; prog_modes = PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # stk500v1 #------------------------------------------------------------ programmer id = "stk500v1"; desc = "Atmel STK500 version 1.x firmware"; type = "stk500"; prog_modes = PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # mib510 #------------------------------------------------------------ programmer id = "mib510"; desc = "Crossbow MIB510 programming board"; type = "stk500"; prog_modes = PM_TPI | PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # stk500v2 #------------------------------------------------------------ programmer id = "stk500v2"; desc = "Atmel STK500 version 2.x firmware"; type = "stk500v2"; prog_modes = PM_TPI | PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # stk500pp #------------------------------------------------------------ programmer id = "stk500pp"; desc = "Atmel STK500 v2 in parallel programming mode"; type = "stk500pp"; prog_modes = PM_HVPP; connection_type = serial; ; #------------------------------------------------------------ # stk500hvsp #------------------------------------------------------------ programmer id = "stk500hvsp"; desc = "Atmel STK500 v2 in high-voltage serial programming mode"; type = "stk500hvsp"; prog_modes = PM_HVSP; connection_type = serial; ; #------------------------------------------------------------ # stk600 #------------------------------------------------------------ programmer id = "stk600"; desc = "Atmel STK600"; type = "stk600"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; ; #------------------------------------------------------------ # stk600pp #------------------------------------------------------------ programmer id = "stk600pp"; desc = "Atmel STK600 in parallel programming mode"; type = "stk600pp"; prog_modes = PM_HVPP; connection_type = usb; ; #------------------------------------------------------------ # stk600hvsp #------------------------------------------------------------ programmer id = "stk600hvsp"; desc = "Atmel STK600 in high-voltage serial programming mode"; type = "stk600hvsp"; prog_modes = PM_HVSP; connection_type = usb; ; #------------------------------------------------------------ # avr910 #------------------------------------------------------------ programmer id = "avr910"; desc = "Atmel Low Cost Serial Programmer"; type = "avr910"; prog_modes = PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # ft245r #------------------------------------------------------------ programmer id = "ft245r"; desc = "FT245R Synchronous BitBang"; type = "ftdi_syncbb"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; reset = 4; # D4 sck = 0; # D0 mosi = 2; # D2 miso = 1; # D1 ; #------------------------------------------------------------ # ft232r #------------------------------------------------------------ programmer id = "ft232r"; desc = "FT232R Synchronous BitBang"; type = "ftdi_syncbb"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; reset = 4; # DTR sck = 0; # TxD mosi = 2; # RTS miso = 1; # RxD ; #------------------------------------------------------------ # bwmega #------------------------------------------------------------ # see http://www.bitwizard.nl/wiki/index.php/FTDI_ATmega programmer id = "bwmega"; desc = "BitWizard ftdi_atmega builtin programmer"; type = "ftdi_syncbb"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; reset = 7; # RI sck = 6; # DCD mosi = 3; # CTS miso = 5; # DSR ; #------------------------------------------------------------ # arduino-ft232r #------------------------------------------------------------ # see http://www.geocities.jp/arduino_diecimila/bootloader/index_en.html # Note: pins are numbered from 1! programmer id = "arduino-ft232r"; desc = "Arduino: FT232R connected to ISP"; type = "ftdi_syncbb"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; reset = 7; # RI X3(4) sck = 5; # DSR X3(2) mosi = 6; # DCD X3(3) miso = 3; # CTS X3(1) ; #------------------------------------------------------------ # tc2030 #------------------------------------------------------------ programmer id = "tc2030"; desc = "Tag-Connect TC2030"; type = "ftdi_syncbb"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; # FOR TPI devices: reset = 3; # CTS = D3 (wire to ~RESET) sck = 2; # RTS = D2 (wire to SCK) mosi = 0; # TxD = D0 (wire to TPIDATA via 1k resistor) miso = 1; # RxD = D1 (wire to TPIDATA directly) ; #------------------------------------------------------------ # diecimila #------------------------------------------------------------ # website mentioned above uses this id programmer parent "arduino-ft232r" id = "diecimila"; desc = "alias for arduino-ft232r"; ; #------------------------------------------------------------ # uncompatino #------------------------------------------------------------ # There is a ATmega328P kit PCB called "uncompatino". # This board allows ISP via its on-board FT232R. # This is designed like Arduino Duemilanove but has no standard ICPS header. # Its 4 pairs of pins are shorted to enable ftdi_syncbb. # http://akizukidenshi.com/catalog/g/gP-07487/ # http://akizukidenshi.com/download/ds/akizuki/k6096_manual_20130816.pdf programmer id = "uncompatino"; desc = "uncompatino with all pairs of pins shorted"; type = "ftdi_syncbb"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; reset = 7; # ri sck = 5; # dsr mosi = 6; # dcd miso = 3; # cts ; #------------------------------------------------------------ # ttl232r #------------------------------------------------------------ # FTDI USB to serial cable TTL-232R-5V with a custom adapter for ICSP # http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm # http://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf # For ICSP pinout see for example http://www.atmel.com/images/doc2562.pdf # (Figure 1. ISP6PIN header pinout and Table 1. Connections required for ISP ...) # TTL-232R GND 1 Black -> ICPS GND (pin 6) # TTL-232R CTS 2 Brown -> ICPS MOSI (pin 4) # TTL-232R VCC 3 Red -> ICPS VCC (pin 2) # TTL-232R TXD 4 Orange -> ICPS RESET (pin 5) # TTL-232R RXD 5 Yellow -> ICPS SCK (pin 3) # TTL-232R RTS 6 Green -> ICPS MISO (pin 1) # Except for VCC and GND, you can connect arbitual pairs as long as # the following table is adjusted. programmer id = "ttl232r"; desc = "FTDI TTL232R-5V with ICSP adapter"; type = "ftdi_syncbb"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; reset = 0; # txd sck = 1; # rxd mosi = 3; # cts miso = 2; # rts ; #------------------------------------------------------------ # usbasp #------------------------------------------------------------ programmer id = "usbasp"; desc = "USBasp, http://www.fischl.de/usbasp/"; type = "usbasp"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x16c0; # VOTI usbpid = 0x05dc; # Obdev's free shared PID usbvendor = "www.fischl.de"; usbproduct = "USBasp"; # following variants are autodetected for id "usbasp" # original usbasp from fischl.de # see above "usbasp" # old usbasp from fischl.de # usbvid = 0x03EB; # ATMEL # usbpid = 0xC7B4; # (unoffical) USBasp # usbvendor = "www.fischl.de"; # usbproduct = "USBasp"; # NIBObee (only if -P nibobee is given on command line) # see below "nibobee" ; #------------------------------------------------------------ # nibobee #------------------------------------------------------------ programmer id = "nibobee"; desc = "NIBObee"; type = "usbasp"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x16c0; # VOTI usbpid = 0x092f; # NIBObee PID usbvendor = "www.nicai-systems.com"; usbproduct = "NIBObee"; ; #------------------------------------------------------------ # usbasp-clone #------------------------------------------------------------ programmer id = "usbasp-clone"; desc = "Any usbasp clone with correct VID/PID"; type = "usbasp"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x16c0; # VOTI usbpid = 0x05dc; # Obdev's free shared PID ; #------------------------------------------------------------ # usbtiny #------------------------------------------------------------ # USBtiny can also be used for TPI programming. # In that case, a resistor of 1 kOhm is needed between MISO and MOSI # pins of the connector, and MISO (pin 1 of the 6-pin connector) # connects to TPIDATA. programmer id = "usbtiny"; desc = "USBtiny simple USB programmer, https://learn.adafruit.com/usbtinyisp"; type = "usbtiny"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x1781; usbpid = 0x0c9f; ; #------------------------------------------------------------ # arduino_gemma #------------------------------------------------------------ # https://github.com/arduino/ArduinoCore-avr/tree/master/bootloaders/gemma programmer id = "arduino_gemma"; desc = "Arduino Gemma bootloader disguised as USBtiny"; type = "usbtiny"; prog_modes = PM_SPM; connection_type = usb; usbvid = 0x2341; usbpid = 0x0c9f; ; #------------------------------------------------------------ # adafruit_gemma #------------------------------------------------------------ # https://github.com/adafruit/Adafruit-Trinket-Gemma-Bootloader programmer id = "adafruit_gemma"; desc = "Adafruit Trinket Gemma bootloader disguised as USBtiny"; type = "usbtiny"; prog_modes = PM_SPM; connection_type = usb; usbvid = 0x1781; usbpid = 0x0c9f; ; #------------------------------------------------------------ # arduinoisp #------------------------------------------------------------ programmer id = "arduinoisp"; desc = "Arduino ISP Programmer"; type = "usbtiny"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x2341; usbpid = 0x0049; ; #------------------------------------------------------------ # arduinoisporg #------------------------------------------------------------ programmer id = "arduinoisporg"; desc = "Arduino ISP Programmer"; type = "usbtiny"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x2a03; usbpid = 0x0049; ; #------------------------------------------------------------ # ehajo-isp #------------------------------------------------------------ # commercial version of USBtiny, using a separate VID/PID programmer id = "ehajo-isp"; desc = "avr-isp-programmer from eHaJo, http://www.eHaJo.de"; type = "usbtiny"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x16d0; usbpid = 0x0ba5; ; #------------------------------------------------------------ # iseavrprog #------------------------------------------------------------ # commercial version of USBtiny, using a separate VID/PID # https://github.com/IowaScaledEngineering/ckt-avrprogrammer programmer id = "iseavrprog"; desc = "USBtiny-based programmer, https://iascaled.com"; type = "usbtiny"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; usbvid = 0x1209; usbpid = 0x6570; ; #------------------------------------------------------------ # micronucleus #------------------------------------------------------------ programmer id = "micronucleus"; desc = "Micronucleus for bootloader"; type = "micronucleus"; prog_modes = PM_SPM; connection_type = usb; usbvid = 0x16d0; usbpid = 0x0753; ; #------------------------------------------------------------ # teensy #------------------------------------------------------------ programmer id = "teensy"; desc = "Teensy for bootloader"; type = "teensy"; prog_modes = PM_SPM; connection_type = usb; usbvid = 0x16c0; usbpid = 0x0478; ; #------------------------------------------------------------ # butterfly #------------------------------------------------------------ programmer id = "butterfly"; desc = "Atmel for bootloader (Butterfly Development Board)"; type = "butterfly"; prog_modes = PM_SPM; connection_type = serial; ; #------------------------------------------------------------ # avr109 #------------------------------------------------------------ programmer id = "avr109"; desc = "Atmel for bootloader using AppNote AVR109"; type = "butterfly"; prog_modes = PM_SPM; connection_type = serial; ; #------------------------------------------------------------ # avr911 #------------------------------------------------------------ programmer id = "avr911"; desc = "Atmel for bootloader using AppNote AVR911 AVROSP"; type = "butterfly"; prog_modes = PM_SPM; connection_type = serial; ; #------------------------------------------------------------ # mkbutterfly #------------------------------------------------------------ # suggested in http://forum.mikrokopter.de/topic-post48317.html programmer id = "mkbutterfly"; desc = "Mikrokopter.de Butterfly for bootloader"; type = "butterfly_mk"; prog_modes = PM_SPM; connection_type = serial; ; #------------------------------------------------------------ # butterfly_mk #------------------------------------------------------------ programmer parent "mkbutterfly" id = "butterfly_mk"; ; #------------------------------------------------------------ # jtagmkI #------------------------------------------------------------ programmer id = "jtagmkI"; desc = "Atmel JTAG ICE (mkI)"; type = "jtagmki"; prog_modes = PM_JTAGmkI; connection_type = serial; baudrate = 115200; # default is 115200 ; #------------------------------------------------------------ # jtag1 #------------------------------------------------------------ # easier to type programmer parent "jtagmkI" id = "jtag1"; ; #------------------------------------------------------------ # jtag1slow #------------------------------------------------------------ # easier to type programmer parent "jtag1" id = "jtag1slow"; baudrate = 19200; ; #------------------------------------------------------------ # jtagmkII #------------------------------------------------------------ # The JTAG ICE mkII has both, serial and USB connectivity. As it is # mostly used through USB these days (AVR Studio 5 only supporting it # that way), we make connection_type = usb the default. Users are # still free to use a serial port with the -P option. programmer id = "jtagmkII"; desc = "Atmel JTAG ICE mkII"; type = "jtagmkii"; prog_modes = PM_JTAG | PM_XMEGAJTAG | PM_AVR32JTAG; connection_type = usb; baudrate = 19200; # default is 19200 ; #------------------------------------------------------------ # jtag2slow #------------------------------------------------------------ # easier to type programmer parent "jtagmkII" id = "jtag2slow"; ; #------------------------------------------------------------ # jtag2fast #------------------------------------------------------------ # JTAG ICE mkII @ 115200 Bd programmer parent "jtag2slow" id = "jtag2fast"; baudrate = 115200; ; #------------------------------------------------------------ # jtag2 #------------------------------------------------------------ # make the fast one the default, people will love that programmer parent "jtag2fast" id = "jtag2"; ; #------------------------------------------------------------ # jtag2isp #------------------------------------------------------------ # JTAG ICE mkII in ISP mode programmer id = "jtag2isp"; desc = "Atmel JTAG ICE mkII in ISP mode"; type = "jtagmkii_isp"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # jtag2dw #------------------------------------------------------------ # JTAG ICE mkII in debugWire mode programmer id = "jtag2dw"; desc = "Atmel JTAG ICE mkII in debugWire mode"; type = "jtagmkii_dw"; prog_modes = PM_debugWIRE; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # jtagmkII_avr32 #------------------------------------------------------------ # JTAG ICE mkII in AVR32 mode programmer id = "jtagmkII_avr32"; desc = "Atmel JTAG ICE mkII in AVR32 mode"; type = "jtagmkii_avr32"; prog_modes = PM_aWire; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # jtag2avr32 #------------------------------------------------------------ # JTAG ICE mkII in AVR32 mode programmer id = "jtag2avr32"; desc = "Atmel JTAG ICE mkII in AVR32 mode"; type = "jtagmkii_avr32"; prog_modes = PM_aWire; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # jtag2pdi #------------------------------------------------------------ # JTAG ICE mkII in PDI mode programmer id = "jtag2pdi"; desc = "Atmel JTAG ICE mkII in PDI mode"; type = "jtagmkii_pdi"; prog_modes = PM_PDI; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # dragon_jtag #------------------------------------------------------------ # AVR Dragon in JTAG mode programmer id = "dragon_jtag"; desc = "Atmel AVR Dragon in JTAG mode"; type = "dragon_jtag"; prog_modes = PM_JTAG | PM_XMEGAJTAG | PM_AVR32JTAG; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # dragon_isp #------------------------------------------------------------ # AVR Dragon in ISP mode programmer id = "dragon_isp"; desc = "Atmel AVR Dragon in ISP mode"; type = "dragon_isp"; prog_modes = PM_TPI | PM_ISP; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # dragon_pp #------------------------------------------------------------ # AVR Dragon in PP mode programmer id = "dragon_pp"; desc = "Atmel AVR Dragon in PP mode"; type = "dragon_pp"; prog_modes = PM_HVPP; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # dragon_hvsp #------------------------------------------------------------ # AVR Dragon in HVSP mode programmer id = "dragon_hvsp"; desc = "Atmel AVR Dragon in HVSP mode"; type = "dragon_hvsp"; prog_modes = PM_HVSP; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # dragon_dw #------------------------------------------------------------ # AVR Dragon in debugWire mode programmer id = "dragon_dw"; desc = "Atmel AVR Dragon in debugWire mode"; type = "dragon_dw"; prog_modes = PM_debugWIRE; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # dragon_pdi #------------------------------------------------------------ # AVR Dragon in PDI mode programmer id = "dragon_pdi"; desc = "Atmel AVR Dragon in PDI mode"; type = "dragon_pdi"; prog_modes = PM_PDI; connection_type = usb; baudrate = 115200; ; #------------------------------------------------------------ # jtag3 #------------------------------------------------------------ programmer id = "jtag3"; desc = "Atmel AVR JTAGICE3 in JTAG mode"; type = "jtagice3"; prog_modes = PM_JTAG | PM_XMEGAJTAG | PM_AVR32JTAG; connection_type = usb; usbpid = 0x2110, 0x2140; ; #------------------------------------------------------------ # jtag3pdi #------------------------------------------------------------ programmer id = "jtag3pdi"; desc = "Atmel AVR JTAGICE3 in PDI mode"; type = "jtagice3_pdi"; prog_modes = PM_PDI; connection_type = usb; usbpid = 0x2110, 0x2140; ; #------------------------------------------------------------ # jtag3updi #------------------------------------------------------------ programmer id = "jtag3updi"; desc = "Atmel AVR JTAGICE3 in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x2110, 0x2140; hvupdi_support = 1; ; #------------------------------------------------------------ # jtag3dw #------------------------------------------------------------ programmer id = "jtag3dw"; desc = "Atmel AVR JTAGICE3 in debugWIRE mode"; type = "jtagice3_dw"; prog_modes = PM_debugWIRE; connection_type = usb; usbpid = 0x2110, 0x2140; ; #------------------------------------------------------------ # jtag3isp #------------------------------------------------------------ programmer id = "jtag3isp"; desc = "Atmel AVR JTAGICE3 in ISP mode"; type = "jtagice3_isp"; prog_modes = PM_ISP; connection_type = usb; usbpid = 0x2110, 0x2140; ; #------------------------------------------------------------ # xplainedpro #------------------------------------------------------------ programmer id = "xplainedpro"; desc = "Atmel AVR XplainedPro in JTAG mode"; type = "jtagice3"; prog_modes = PM_JTAG | PM_XMEGAJTAG | PM_AVR32JTAG; connection_type = usb; usbpid = 0x2111; ; #------------------------------------------------------------ # xplainedpro_updi #------------------------------------------------------------ programmer id = "xplainedpro_updi"; desc = "Atmel AVR XplainedPro in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x2111; hvupdi_support = 1; ; #------------------------------------------------------------ # xplainedmini #------------------------------------------------------------ programmer id = "xplainedmini"; desc = "Atmel AVR XplainedMini in ISP mode"; type = "jtagice3_isp"; prog_modes = PM_ISP; connection_type = usb; usbpid = 0x2145; ; #------------------------------------------------------------ # xplainedmini_dw #------------------------------------------------------------ programmer id = "xplainedmini_dw"; desc = "Atmel AVR XplainedMini in debugWIRE mode"; type = "jtagice3_dw"; prog_modes = PM_debugWIRE; connection_type = usb; usbpid = 0x2145; ; #------------------------------------------------------------ # xplainedmini_updi #------------------------------------------------------------ programmer id = "xplainedmini_updi"; desc = "Atmel AVR XplainedMini in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x2145; hvupdi_support = 1; ; #------------------------------------------------------------ # atmelice #------------------------------------------------------------ programmer id = "atmelice"; desc = "Atmel-ICE (ARM/AVR) in JTAG mode"; type = "jtagice3"; prog_modes = PM_JTAG | PM_XMEGAJTAG | PM_AVR32JTAG; connection_type = usb; usbpid = 0x2141; ; #------------------------------------------------------------ # atmelice_pdi #------------------------------------------------------------ programmer id = "atmelice_pdi"; desc = "Atmel-ICE (ARM/AVR) in PDI mode"; type = "jtagice3_pdi"; prog_modes = PM_PDI; connection_type = usb; usbpid = 0x2141; ; #------------------------------------------------------------ # atmelice_updi #------------------------------------------------------------ programmer id = "atmelice_updi"; desc = "Atmel-ICE (ARM/AVR) in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x2141; hvupdi_support = 1; ; #------------------------------------------------------------ # atmelice_dw #------------------------------------------------------------ programmer id = "atmelice_dw"; desc = "Atmel-ICE (ARM/AVR) in debugWIRE mode"; type = "jtagice3_dw"; prog_modes = PM_debugWIRE; connection_type = usb; usbpid = 0x2141; ; #------------------------------------------------------------ # atmelice_isp #------------------------------------------------------------ programmer id = "atmelice_isp"; desc = "Atmel-ICE (ARM/AVR) in ISP mode"; type = "jtagice3_isp"; prog_modes = PM_ISP; connection_type = usb; usbpid = 0x2141; ; #------------------------------------------------------------ # powerdebugger #------------------------------------------------------------ programmer id = "powerdebugger"; desc = "Atmel PowerDebugger (ARM/AVR) in JTAG mode"; type = "jtagice3"; prog_modes = PM_JTAG | PM_XMEGAJTAG | PM_AVR32JTAG; connection_type = usb; usbpid = 0x2144; ; #------------------------------------------------------------ # powerdebugger_pdi #------------------------------------------------------------ programmer id = "powerdebugger_pdi"; desc = "Atmel PowerDebugger (ARM/AVR) in PDI mode"; type = "jtagice3_pdi"; prog_modes = PM_PDI; connection_type = usb; usbpid = 0x2144; ; #------------------------------------------------------------ # powerdebugger_updi #------------------------------------------------------------ programmer id = "powerdebugger_updi"; desc = "Atmel PowerDebugger (ARM/AVR) in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x2144; hvupdi_support = 0, 1; ; #------------------------------------------------------------ # powerdebugger_dw #------------------------------------------------------------ programmer id = "powerdebugger_dw"; desc = "Atmel PowerDebugger (ARM/AVR) in debugWire mode"; type = "jtagice3_dw"; prog_modes = PM_debugWIRE; connection_type = usb; usbpid = 0x2144; ; #------------------------------------------------------------ # powerdebugger_isp #------------------------------------------------------------ programmer id = "powerdebugger_isp"; desc = "Atmel PowerDebugger (ARM/AVR) in ISP mode"; type = "jtagice3_isp"; prog_modes = PM_ISP; connection_type = usb; usbpid = 0x2144; ; #------------------------------------------------------------ # pickit4_updi #------------------------------------------------------------ programmer id = "pickit4_updi"; desc = "MPLAB(R) PICkit 4 in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x2177, 0x2178, 0x2179; hvupdi_support = 0, 1, 2; ; #------------------------------------------------------------ # pickit4_pdi #------------------------------------------------------------ programmer id = "pickit4_pdi"; desc = "MPLAB(R) PICkit 4 in PDI mode"; type = "jtagice3_pdi"; prog_modes = PM_PDI; connection_type = usb; usbpid = 0x2177, 0x2178, 0x2179; ; #------------------------------------------------------------ # pickit4_isp #------------------------------------------------------------ programmer id = "pickit4_isp"; desc = "MPLAB(R) PICkit 4 in ISP mode"; type = "jtagice3_isp"; prog_modes = PM_ISP; connection_type = usb; usbpid = 0x2177, 0x2178, 0x2179; ; #------------------------------------------------------------ # snap_updi #------------------------------------------------------------ programmer id = "snap_updi"; desc = "MPLAB(R) SNAP in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x217f, 0x2180, 0x2181; hvupdi_support = 1; ; #------------------------------------------------------------ # snap_pdi #------------------------------------------------------------ programmer id = "snap_pdi"; desc = "MPLAB(R) SNAP in PDI mode"; type = "jtagice3_pdi"; prog_modes = PM_PDI; connection_type = usb; usbpid = 0x217f, 0x2180, 0x2181; ; #------------------------------------------------------------ # snap_isp #------------------------------------------------------------ programmer id = "snap_isp"; desc = "MPLAB(R) SNAP in ISP mode"; type = "jtagice3_isp"; prog_modes = PM_ISP; connection_type = usb; usbpid = 0x217f, 0x2180, 0x2181; ; #------------------------------------------------------------ # pkobn_updi #------------------------------------------------------------ programmer id = "pkobn_updi"; desc = "Curiosity nano (nEDBG) in UPDI mode"; type = "jtagice3_updi"; prog_modes = PM_UPDI; connection_type = usb; usbpid = 0x2175; hvupdi_support = 1; ; #------------------------------------------------------------ # pavr #------------------------------------------------------------ programmer id = "pavr"; desc = "Jason Kyle's pAVR Serial Programmer"; type = "avr910"; prog_modes = PM_ISP; connection_type = serial; ; #------------------------------------------------------------ # pickit2 #------------------------------------------------------------ programmer id = "pickit2"; desc = "MicroChip's PICkit2 Programmer"; type = "pickit2"; prog_modes = PM_ISP; connection_type = usb; ; #------------------------------------------------------------ # flip1 #------------------------------------------------------------ programmer id = "flip1"; desc = "FLIP for bootloader using USB DFU protocol version 1 (doc7618)"; type = "flip1"; prog_modes = PM_SPM; connection_type = usb; ; #------------------------------------------------------------ # flip2 #------------------------------------------------------------ programmer id = "flip2"; desc = "FLIP for bootloader using USB DFU protocol version 2 (AVR4023)"; type = "flip2"; prog_modes = PM_SPM; connection_type = usb; ; #------------------------------------------------------------ # ponyser #------------------------------------------------------------ # some ultra cheap programmers use bitbanging on the serialport # # PC - DB9 - Pins for RS232: # # GND 5 -- |O # | O| <- 9 RI # DTR 4 <- |O | # | O| <- 8 CTS # TXD 3 <- |O | # | O| -> 7 RTS # RXD 2 -> |O | # | O| <- 6 DSR # DCD 1 -> |O # # Using RXD is currently not supported. # Using RI is not supported under Win32 but is supported under Posix. # serial ponyprog design (dasa2 in uisp) # reset=!txd sck=rts mosi=dtr miso=cts programmer id = "ponyser"; desc = "design ponyprog serial, reset=!txd sck=rts mosi=dtr miso=cts"; type = "serbb"; prog_modes = PM_TPI | PM_ISP; connection_type = serial; reset = ~3; sck = 7; mosi = 4; miso = 8; ; #------------------------------------------------------------ # siprog #------------------------------------------------------------ # Same as above, different name # reset=!txd sck=rts mosi=dtr miso=cts programmer parent "ponyser" id = "siprog"; desc = "Lancos SI-Prog "; ; #------------------------------------------------------------ # dasa #------------------------------------------------------------ # unknown (dasa in uisp) # reset=rts sck=dtr mosi=txd miso=cts programmer id = "dasa"; desc = "serial port banging, reset=rts sck=dtr mosi=txd miso=cts"; type = "serbb"; prog_modes = PM_TPI | PM_ISP; connection_type = serial; reset = 7; sck = 4; mosi = 3; miso = 8; ; #------------------------------------------------------------ # dasa3 #------------------------------------------------------------ # unknown (dasa3 in uisp) # reset=!dtr sck=rts mosi=txd miso=cts programmer id = "dasa3"; desc = "serial port banging, reset=!dtr sck=rts mosi=txd miso=cts"; type = "serbb"; prog_modes = PM_TPI | PM_ISP; connection_type = serial; reset = ~4; sck = 7; mosi = 3; miso = 8; ; #------------------------------------------------------------ # C2N232i #------------------------------------------------------------ # C2N232i (jumper configuration "auto") # reset=dtr sck=!rts mosi=!txd miso=!cts programmer id = "c2n232i"; desc = "serial port banging, reset=dtr sck=!rts mosi=!txd miso=!cts"; type = "serbb"; prog_modes = PM_TPI | PM_ISP; connection_type = serial; reset = 4; sck = ~7; mosi = ~3; miso = ~8; ; #------------------------------------------------------------ # jtag2updi #------------------------------------------------------------ # JTAG2UPDI # https://github.com/ElTangas/jtag2updi programmer id = "jtag2updi"; desc = "JTAGv2 to UPDI bridge"; type = "jtagmkii_updi"; prog_modes = PM_UPDI; connection_type = serial; baudrate = 115200; hvupdi_support = 1; ; # # PART DEFINITIONS # #------------------------------------------------------------ # ATtiny11 #------------------------------------------------------------ # This is an HVSP-only device. part desc = "ATtiny11"; id = "t11"; prog_modes = PM_HVSP; mcuid = 8; n_interrupts = 5; stk500_devcode = 0x11; chip_erase_delay = 20000; signature = 0x1e 0x90 0x04; serial = no; timeout = 200; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x00, 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78, 0x78, 0x00, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayus = 50; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; memory "eeprom" size = 64; delay = 5; blocksize = 64; readsize = 256; ; memory "flash" size = 1024; delay = 3; blocksize = 128; readsize = 256; ; memory "fuse" size = 1; ; memory "lock" size = 1; ; memory "signature" size = 3; ; memory "calibration" size = 1; ; ; #------------------------------------------------------------ # ATtiny12 #------------------------------------------------------------ part desc = "ATtiny12"; id = "t12"; prog_modes = PM_ISP | PM_HVSP; mcuid = 9; n_interrupts = 6; stk500_devcode = 0x12; avr910_devcode = 0x55; chip_erase_delay = 20000; signature = 0x1e 0x90 0x05; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x00, 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78, 0x78, 0x00, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayus = 50; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 64; min_write_delay = 9000; max_write_delay = 20000; readback = 0xff 0xff; mode = 4; delay = 8; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.xxxx--xxaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; ; memory "flash" size = 1024; min_write_delay = 4500; max_write_delay = 20000; readback = 0xff 0xff; mode = 4; delay = 5; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--xxxx.xxxx--xxxx.xxxx--oooo.oooo"; write = "1010.1100--101x.xxxx--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xoox"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny13 #------------------------------------------------------------ part desc = "ATtiny13"; id = "t13"; prog_modes = PM_SPM | PM_ISP | PM_HVSP | PM_debugWIRE; mcuid = 10; n_interrupts = 10; stk500_devcode = 0x14; chip_erase_delay = 4000; signature = 0x1e 0x90 0x07; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x66, 0x68, 0x78, 0x68, 0x68, 0x7a, 0x6a, 0x68, 0x78, 0x78, 0x7d, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; flash_instr = 0xb4, 0x0e, 0x1e; eeprom_instr = 0xbb, 0xfe, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x0e, 0xb4, 0x0e, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayus = 90; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; ocdrev = 0; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 64; page_size = 4; min_write_delay = 4000; max_write_delay = 4000; readback = 0xff 0xff; mode = 65; delay = 5; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--xxaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--xxaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 1024; page_size = 32; num_pages = 32; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.000a--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.000a--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxx.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxx.aaaa--iiii.iiii"; writepage = "0100.1100--0000.000a--aaaa.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 2; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny13A #------------------------------------------------------------ part parent "t13" desc = "ATtiny13A"; id = "t13a"; mcuid = 11; ; #------------------------------------------------------------ # ATtiny15 #------------------------------------------------------------ part desc = "ATtiny15"; id = "t15"; prog_modes = PM_ISP | PM_HVSP; mcuid = 12; n_interrupts = 9; stk500_devcode = 0x13; avr910_devcode = 0x56; chip_erase_delay = 8200; signature = 0x1e 0x90 0x06; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x00, 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78, 0x78, 0x00, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; hventerstabdelay = 100; latchcycles = 16; togglevtg = 1; poweroffdelay = 25; resetdelayus = 50; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; hvspcmdexedelay = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 64; min_write_delay = 8200; max_write_delay = 8200; readback = 0xff 0xff; mode = 4; delay = 10; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.xxxx--xxaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; ; memory "flash" size = 1024; min_write_delay = 4100; max_write_delay = 4100; readback = 0xff 0xff; mode = 4; delay = 5; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--xxxx.xxxx--xxxx.xxxx--oooo.xxoo"; write = "1010.1100--101x.xxxx--xxxx.xxxx--iiii.11ii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xoox"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s1200 #------------------------------------------------------------ part desc = "AT90S1200"; id = "1200"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 183; n_interrupts = 4; stk500_devcode = 0x33; avr910_devcode = 0x13; chip_erase_delay = 20000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x90 0x01; is_at90s1200 = yes; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 1; pollvalue = 0xff; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 1; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 64; min_write_delay = 4000; max_write_delay = 9000; readback = 0x00 0xff; mode = 4; delay = 20; blocksize = 32; readsize = 256; read = "1010.0000--xxxx.xxxx--xxaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; ; memory "flash" size = 1024; min_write_delay = 4000; max_write_delay = 9000; readback = 0xff 0xff; mode = 2; delay = 15; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 20000; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s4414 #------------------------------------------------------------ part desc = "AT90S4414"; id = "4414"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 190; n_interrupts = 13; stk500_devcode = 0x50; avr910_devcode = 0x28; chip_erase_delay = 20000; signature = 0x1e 0x92 0x01; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 1; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; min_write_delay = 9000; max_write_delay = 20000; readback = 0x80 0x7f; mode = 4; delay = 12; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" size = 4096; min_write_delay = 9000; max_write_delay = 20000; readback = 0x7f 0x7f; mode = 4; delay = 12; blocksize = 64; readsize = 256; read_lo = "0010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s2313 #------------------------------------------------------------ part desc = "AT90S2313"; id = "2313"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 186; n_interrupts = 11; stk500_devcode = 0x40; avr910_devcode = 0x20; chip_erase_delay = 20000; signature = 0x1e 0x91 0x01; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 1; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; min_write_delay = 4000; max_write_delay = 9000; readback = 0x80 0x7f; mode = 4; delay = 12; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; ; memory "flash" size = 2048; min_write_delay = 4000; max_write_delay = 9000; readback = 0x7f 0x7f; mode = 4; delay = 12; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xxaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xxaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; write = "1010.1100--111x.xiix--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s2333 #------------------------------------------------------------ part ##### WARNING: No XML file for device 'AT90S2333'! ##### desc = "AT90S2333"; id = "2333"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 188; n_interrupts = 14; stk500_devcode = 0x42; avr910_devcode = 0x34; chip_erase_delay = 20000; signature = 0x1e 0x91 0x05; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 1; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; min_write_delay = 9000; max_write_delay = 20000; readback = 0x00 0xff; mode = 4; delay = 12; blocksize = 128; readsize = 256; read = "1010.0000--xxxx.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; ; memory "flash" size = 2048; min_write_delay = 9000; max_write_delay = 20000; readback = 0xff 0xff; mode = 4; delay = 12; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xxaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xxaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 20000; pwroff_after_write = yes; read = "0101.0000--xxxx.xxxx--xxxx.xxxx--xxoo.oooo"; write = "1010.1100--101i.iiii--xxxx.xxxx--xxxx.xxxx"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 20000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xoox"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s2343 (also AT90s2323 and ATtiny22) #------------------------------------------------------------ part desc = "AT90S2343"; id = "2343"; prog_modes = PM_SPM | PM_ISP | PM_HVSP; mcuid = 189; n_interrupts = 3; stk500_devcode = 0x43; avr910_devcode = 0x4c; chip_erase_delay = 18000; signature = 0x1e 0x91 0x03; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x00, 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78, 0x78, 0x00, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; hventerstabdelay = 100; latchcycles = 1; poweroffdelay = 25; resetdelayus = 50; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; min_write_delay = 9000; max_write_delay = 20000; readback = 0x00 0xff; mode = 4; delay = 12; blocksize = 64; readsize = 256; read = "1010.0000--0000.0000--xaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.0000--xaaa.aaaa--iiii.iiii"; ; memory "flash" size = 2048; min_write_delay = 9000; max_write_delay = 20000; readback = 0xff 0xff; mode = 4; delay = 12; blocksize = 128; readsize = 128; read_lo = "0010.0000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xxaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xxaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 20000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--ooox.xxxo"; write = "1010.1100--1011.111i--xxxx.xxxx--xxxx.xxxx"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 20000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--ooox.xxxo"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s4433 #------------------------------------------------------------ part desc = "AT90S4433"; id = "4433"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 191; n_interrupts = 14; stk500_devcode = 0x51; avr910_devcode = 0x30; chip_erase_delay = 20000; signature = 0x1e 0x92 0x03; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 1; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; min_write_delay = 9000; max_write_delay = 20000; readback = 0x00 0xff; mode = 4; delay = 12; blocksize = 128; readsize = 256; read = "1010.0000--xxxx.xxxx--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--aaaa.aaaa--iiii.iiii"; ; memory "flash" size = 4096; min_write_delay = 9000; max_write_delay = 20000; readback = 0xff 0xff; mode = 4; delay = 12; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 20000; pwroff_after_write = yes; read = "0101.0000--xxxx.xxxx--xxxx.xxxx--xxoo.oooo"; write = "1010.1100--101i.iiii--xxxx.xxxx--xxxx.xxxx"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 20000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xoox"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s4434 #------------------------------------------------------------ part ##### WARNING: No XML file for device 'AT90S4434'! ##### desc = "AT90S4434"; id = "4434"; prog_modes = PM_SPM | PM_ISP; mcuid = 192; n_interrupts = 17; stk500_devcode = 0x52; avr910_devcode = 0x6c; chip_erase_delay = 20000; signature = 0x1e 0x92 0x02; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; min_write_delay = 9000; max_write_delay = 20000; readback = 0x00 0xff; read = "1010.0000--xxxx.xxxx--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--aaaa.aaaa--iiii.iiii"; ; memory "flash" size = 4096; min_write_delay = 9000; max_write_delay = 20000; readback = 0xff 0xff; read_lo = "0010.0000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 20000; read = "0101.0000--xxxx.xxxx--xxxx.xxxx--xxoo.oooo"; write = "1010.1100--101i.iiii--xxxx.xxxx--xxxx.xxxx"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 20000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xoox"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s8515 #------------------------------------------------------------ part desc = "AT90S8515"; id = "8515"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 193; n_interrupts = 13; stk500_devcode = 0x60; avr910_devcode = 0x38; chip_erase_delay = 20000; signature = 0x1e 0x93 0x01; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; resetdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; min_write_delay = 4000; max_write_delay = 9000; readback = 0x80 0x7f; mode = 4; delay = 12; blocksize = 128; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" size = 8192; min_write_delay = 4000; max_write_delay = 9000; readback = 0x7f 0x7f; mode = 4; delay = 12; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90s8535 #------------------------------------------------------------ part desc = "AT90S8535"; id = "8535"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 195; n_interrupts = 17; stk500_devcode = 0x61; avr910_devcode = 0x68; chip_erase_delay = 20000; signature = 0x1e 0x93 0x03; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 1; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; min_write_delay = 9000; max_write_delay = 20000; readback = 0x00 0xff; mode = 4; delay = 12; blocksize = 128; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" size = 8192; min_write_delay = 9000; max_write_delay = 20000; readback = 0xff 0xff; mode = 4; delay = 12; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write_lo = "0100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; write_hi = "0100.1000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xxxo"; write = "1010.1100--1011.111i--xxxx.xxxx--xxxx.xxxx"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--ooxx.xxxx"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega103 #------------------------------------------------------------ part desc = "ATmega103"; id = "m103"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 84; n_interrupts = 24; stk500_devcode = 0xb1; avr910_devcode = 0x41; chip_erase_delay = 112000; signature = 0x1e 0x97 0x01; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x8e, 0x9e, 0x2e, 0x3e, 0xae, 0xbe, 0x4e, 0x5e, 0xce, 0xde, 0x6e, 0x7e, 0xee, 0xde, 0x66, 0x76, 0xe6, 0xf6, 0x6a, 0x7a, 0xea, 0x7a, 0x7f, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepulsewidth = 15; programfusepulsewidth = 2; programlockpolltimeout = 10; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; min_write_delay = 4000; max_write_delay = 9000; readback = 0x80 0x7f; mode = 4; delay = 12; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 0x20000; page_size = 256; num_pages = 512; min_write_delay = 22000; max_write_delay = 56000; readback = 0xff 0xff; mode = 17; delay = 70; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "fuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--xxxx.xxxx--xxxx.xxxx--xxox.o1oo"; write = "1010.1100--1011.i1ii--xxxx.xxxx--xxxx.xxxx"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xoox"; write = "1010.1100--1111.1ii1--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega64 #------------------------------------------------------------ part desc = "ATmega64"; id = "m64"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG | PM_JTAGmkI; mcuid = 72; n_interrupts = 35; stk500_devcode = 0xa0; avr910_devcode = 0x45; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x96 0x02; reset = io; allowfullpagebitstream = yes; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x22; spmcr = 0x68; ocdrev = 2; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 2048; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 20; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 0x10000; page_size = 256; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--xaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--xaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega64A #------------------------------------------------------------ part parent "m64" desc = "ATmega64A"; id = "m64a"; mcuid = 73; ; #------------------------------------------------------------ # ATmega128 #------------------------------------------------------------ part desc = "ATmega128"; id = "m128"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG | PM_JTAGmkI; mcuid = 85; n_interrupts = 35; stk500_devcode = 0xb2; avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x97 0x02; reset = io; allowfullpagebitstream = yes; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x22; rampz = 0x3b; spmcr = 0x68; ocdrev = 1; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 12; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 0x20000; page_size = 256; num_pages = 512; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega128A #------------------------------------------------------------ part parent "m128" desc = "ATmega128A"; id = "m128a"; mcuid = 86; ; #------------------------------------------------------------ # AT90CAN128 #------------------------------------------------------------ part desc = "AT90CAN128"; id = "c128"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG | PM_JTAGmkI; mcuid = 176; n_interrupts = 37; stk500_devcode = 0xb3; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; # avr910_devcode = 0x43; signature = 0x1e 0x97 0x81; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; eecr = 0x3f; ocdrev = 3; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 8; readsize = 256; read = "1010.0000--000x.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.aaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x20000; page_size = 256; num_pages = 512; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90CAN64 #------------------------------------------------------------ part desc = "AT90CAN64"; id = "c64"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 172; n_interrupts = 37; stk500_devcode = 0xb3; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; # avr910_devcode = 0x43; signature = 0x1e 0x96 0x81; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; eecr = 0x3f; ocdrev = 3; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 2048; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 8; readsize = 256; read = "1010.0000--000x.xaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.xaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x10000; page_size = 256; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90CAN32 #------------------------------------------------------------ part desc = "AT90CAN32"; id = "c32"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 171; n_interrupts = 37; stk500_devcode = 0xb3; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; # avr910_devcode = 0x43; signature = 0x1e 0x95 0x81; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; eecr = 0x3f; ocdrev = 3; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 1024; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 8; readsize = 256; read = "1010.0000--000x.xxaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.xxaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 256; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega16 #------------------------------------------------------------ part desc = "ATmega16"; id = "m16"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG | PM_JTAGmkI; mcuid = 49; n_interrupts = 21; stk500_devcode = 0x82; avr910_devcode = 0x74; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x94 0x03; reset = io; allowfullpagebitstream = yes; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; progmodedelay = 100; latchcycles = 6; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 2; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 10; blocksize = 128; readsize = 256; read = "1010.0000--00xx.xxaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--00aa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--000x.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega16A #------------------------------------------------------------ part parent "m16" desc = "ATmega16A"; id = "m16a"; mcuid = 50; ; #------------------------------------------------------------ # ATmega324P #------------------------------------------------------------ part desc = "ATmega324P"; id = "m324p"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 111; n_interrupts = 31; stk500_devcode = 0x82; # no STK500v1 support, use the ATmega16 one avr910_devcode = 0x74; chip_erase_delay = 55000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x95 0x08; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 1024; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 128; readsize = 256; read = "1010.0000--00xx.xaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xaaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 128; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--0aaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--1111.1iii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega164P #------------------------------------------------------------ part parent "m324p" desc = "ATmega164P"; id = "m164p"; mcuid = 93; signature = 0x1e 0x94 0x0a; memory "eeprom" size = 512; ; memory "flash" size = 0x4000; num_pages = 128; ; ; #------------------------------------------------------------ # ATmega164PA #------------------------------------------------------------ part parent "m164p" desc = "ATmega164PA"; id = "m164pa"; mcuid = 94; ; #------------------------------------------------------------ # ATmega164A #------------------------------------------------------------ part parent "m164p" desc = "ATmega164A"; id = "m164a"; mcuid = 92; signature = 0x1e 0x94 0x0f; ; #------------------------------------------------------------ # ATmega324PB #------------------------------------------------------------ part parent "m324p" desc = "ATmega324PB"; id = "m324pb"; mcuid = 113; signature = 0x1e 0x95 0x17; ; #------------------------------------------------------------ # ATmega324PA #------------------------------------------------------------ part parent "m324p" desc = "ATmega324PA"; id = "m324pa"; mcuid = 112; signature = 0x1e 0x95 0x11; ; #------------------------------------------------------------ # ATmega324A #------------------------------------------------------------ part parent "m324p" desc = "ATmega324A"; id = "m324a"; mcuid = 110; signature = 0x1e 0x95 0x15; ; #------------------------------------------------------------ # ATmega644 #------------------------------------------------------------ part desc = "ATmega644"; id = "m644"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 127; n_interrupts = 28; stk500_devcode = 0x82; # no STK500v1 support, use the ATmega16 one avr910_devcode = 0x74; chip_erase_delay = 55000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x96 0x09; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 2048; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 128; readsize = 256; read = "1010.0000--00xx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.aaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x10000; page_size = 256; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--00xx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--00xx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--1111.1iii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega644A #------------------------------------------------------------ part parent "m644" desc = "ATmega644A"; id = "m644a"; mcuid = 128; n_interrupts = 31; ; #------------------------------------------------------------ # ATmega644P #------------------------------------------------------------ part parent "m644" desc = "ATmega644P"; id = "m644p"; mcuid = 129; n_interrupts = 31; signature = 0x1e 0x96 0x0a; ; #------------------------------------------------------------ # ATmega644PA #------------------------------------------------------------ part parent "m644" desc = "ATmega644PA"; id = "m644pa"; mcuid = 130; n_interrupts = 31; signature = 0x1e 0x96 0x0a; ; #------------------------------------------------------------ # ATmega1284 #------------------------------------------------------------ part desc = "ATmega1284"; id = "m1284"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 140; n_interrupts = 35; stk500_devcode = 0x82; # no STK500v1 support, use the ATmega16 one avr910_devcode = 0x74; chip_erase_delay = 55000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x97 0x06; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02; hventerstabdelay = 100; latchcycles = 6; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 128; readsize = 256; read = "1010.0000--00xx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.aaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x20000; page_size = 256; num_pages = 512; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--00xx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--00xx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--1111.1iii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega1284P #------------------------------------------------------------ part parent "m1284" desc = "ATmega1284P"; id = "m1284p"; mcuid = 141; signature = 0x1e 0x97 0x05; ; #------------------------------------------------------------ # ATmega162 #------------------------------------------------------------ part desc = "ATmega162"; id = "m162"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG | PM_JTAGmkI; mcuid = 90; n_interrupts = 28; stk500_devcode = 0x83; avr910_devcode = 0x63; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x94 0x04; reset = io; allowfullpagebitstream = yes; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x04; spmcr = 0x57; ocdrev = 2; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--00xx.xxaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 128; readsize = 256; read_lo = "0010.0000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--00aa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 16000; max_write_delay = 16000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 16000; max_write_delay = 16000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 16000; max_write_delay = 16000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--1111.1iii"; ; memory "lock" size = 1; min_write_delay = 16000; max_write_delay = 16000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--00xx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--00xx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega163 #------------------------------------------------------------ part desc = "ATmega163"; id = "m163"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 91; n_interrupts = 18; stk500_devcode = 0x81; avr910_devcode = 0x64; chip_erase_delay = 32000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x94 0x02; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepolltimeout = 30; programfusepolltimeout = 2; programlockpolltimeout = 2; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; min_write_delay = 4000; max_write_delay = 4000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 16000; max_write_delay = 16000; readback = 0xff 0xff; mode = 17; delay = 20; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--xxxa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.0000--0000.0000--xxxx.xxxx--ooxx.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--ii11.iiii"; ; memory "hfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.1000--xxxx.xxxx--xxxx.1ooo"; write = "1010.1100--1010.1000--xxxx.xxxx--1111.1iii"; ; memory "lock" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.0000--xxxx.0xxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega169 #------------------------------------------------------------ part desc = "ATmega169"; id = "m169"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG | PM_JTAGmkI; mcuid = 104; n_interrupts = 23; stk500_devcode = 0x85; avr910_devcode = 0x78; chip_erase_delay = 9000; signature = 0x1e 0x94 0x05; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 2; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--xxxa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; memory "lock" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega169A #------------------------------------------------------------ part parent "m169" desc = "ATmega169A"; id = "m169a"; mcuid = 105; signature = 0x1e 0x94 0x11; reset = io; ; #------------------------------------------------------------ # ATmega169P #------------------------------------------------------------ part parent "m169" desc = "ATmega169P"; id = "m169p"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 106; reset = io; ; #------------------------------------------------------------ # ATmega169PA #------------------------------------------------------------ part parent "m169" desc = "ATmega169PA"; id = "m169pa"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 107; reset = io; ; #------------------------------------------------------------ # ATmega329 #------------------------------------------------------------ part desc = "ATmega329"; id = "m329"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 121; n_interrupts = 23; # stk500_devcode = 0x85; # no STK500 support, only STK500v2 # avr910_devcode = 0x?; # try the ATmega169 one: avr910_devcode = 0x75; chip_erase_delay = 9000; signature = 0x1e 0x95 0x03; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 1024; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 8; readsize = 256; read = "1010.0000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 128; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--xaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--xaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega329A #------------------------------------------------------------ part parent "m329" desc = "ATmega329A"; id = "m329a"; mcuid = 122; ; #------------------------------------------------------------ # ATmega329P #------------------------------------------------------------ part parent "m329" desc = "ATmega329P"; id = "m329p"; mcuid = 123; signature = 0x1e 0x95 0x0b; ; #------------------------------------------------------------ # ATmega329PA #------------------------------------------------------------ part parent "m329" desc = "ATmega329PA"; id = "m329pa"; mcuid = 124; signature = 0x1e 0x95 0x0b; ; #------------------------------------------------------------ # ATmega3290 #------------------------------------------------------------ part parent "m329" desc = "ATmega3290"; id = "m3290"; mcuid = 150; n_interrupts = 25; signature = 0x1e 0x95 0x04; ; #------------------------------------------------------------ # ATmega3290A #------------------------------------------------------------ part parent "m329" desc = "ATmega3290A"; id = "m3290a"; mcuid = 151; n_interrupts = 25; signature = 0x1e 0x95 0x04; ; #------------------------------------------------------------ # ATmega3290P #------------------------------------------------------------ part parent "m329" desc = "ATmega3290P"; id = "m3290p"; mcuid = 152; n_interrupts = 25; signature = 0x1e 0x95 0x0c; ; #------------------------------------------------------------ # ATmega3290PA #------------------------------------------------------------ part parent "m329" desc = "ATmega3290PA"; id = "m3290pa"; mcuid = 153; n_interrupts = 25; signature = 0x1e 0x95 0x0c; ; #------------------------------------------------------------ # ATmega649 #------------------------------------------------------------ part desc = "ATmega649"; id = "m649"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 135; n_interrupts = 23; # stk500_devcode = 0x85; # no STK500 support, only STK500v2 # avr910_devcode = 0x?; # try the ATmega169 one: avr910_devcode = 0x75; chip_erase_delay = 9000; signature = 0x1e 0x96 0x03; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 2048; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 8; readsize = 256; read = "1010.0000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.xaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x10000; page_size = 256; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega649A #------------------------------------------------------------ part parent "m649" desc = "ATmega649A"; id = "m649a"; mcuid = 136; ; #------------------------------------------------------------ # ATmega649P #------------------------------------------------------------ part parent "m649" desc = "ATmega649P"; id = "m649p"; mcuid = 137; signature = 0x1e 0x96 0x0b; ; #------------------------------------------------------------ # ATmega6490 #------------------------------------------------------------ part parent "m649" desc = "ATmega6490"; id = "m6490"; mcuid = 157; n_interrupts = 25; signature = 0x1e 0x96 0x04; ; #------------------------------------------------------------ # ATmega6490A #------------------------------------------------------------ part parent "m649" desc = "ATmega6490A"; id = "m6490a"; mcuid = 158; n_interrupts = 25; signature = 0x1e 0x96 0x04; ; #------------------------------------------------------------ # ATmega6490P #------------------------------------------------------------ part parent "m649" desc = "ATmega6490P"; id = "m6490p"; mcuid = 159; n_interrupts = 25; signature = 0x1e 0x96 0x0c; ; #------------------------------------------------------------ # ATmega32 #------------------------------------------------------------ part desc = "ATmega32"; id = "m32"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG | PM_JTAGmkI; mcuid = 58; n_interrupts = 21; stk500_devcode = 0x91; avr910_devcode = 0x72; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x95 0x02; reset = io; allowfullpagebitstream = yes; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 2; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 1024; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 10; blocksize = 64; readsize = 256; read = "1010.0000--00xx.xxaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 128; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--00aa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--00xx.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega161 #------------------------------------------------------------ part desc = "ATmega161"; id = "m161"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 89; n_interrupts = 21; stk500_devcode = 0x80; avr910_devcode = 0x60; chip_erase_delay = 28000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x94 0x01; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; chiperasepolltimeout = 30; programfusepolltimeout = 2; programlockpolltimeout = 2; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; min_write_delay = 3400; max_write_delay = 3400; readback = 0xff 0xff; mode = 4; delay = 5; blocksize = 128; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 14000; max_write_delay = 14000; readback = 0xff 0xff; mode = 33; delay = 16; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--xxxa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "fuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.0000--xxxx.xxxx--xxxx.xxxx--xoxo.oooo"; write = "1010.1100--101x.xxxx--xxxx.xxxx--1i1i.iiii"; ; memory "lock" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega32A #------------------------------------------------------------ part parent "m32" desc = "ATmega32A"; id = "m32a"; mcuid = 59; ; #------------------------------------------------------------ # ATmega8 #------------------------------------------------------------ part desc = "ATmega8"; id = "m8"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 45; n_interrupts = 19; stk500_devcode = 0x70; avr910_devcode = 0x76; chip_erase_delay = 10000; pagel = 0xd7; bs2 = 0xc2; signature = 0x1e 0x93 0x07; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 2; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 20; blocksize = 128; readsize = 256; read = "1010.0000--00xx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0x00; mode = 33; delay = 10; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--0000.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--0000.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--00xx.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega8A #------------------------------------------------------------ part parent "m8" desc = "ATmega8A"; id = "m8a"; mcuid = 46; ; #------------------------------------------------------------ # ATmega8515 #------------------------------------------------------------ part desc = "ATmega8515"; id = "m8515"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 160; n_interrupts = 17; stk500_devcode = 0x63; avr910_devcode = 0x3a; chip_erase_delay = 9000; signature = 0x1e 0x93 0x06; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 20; blocksize = 128; readsize = 256; read = "1010.0000--00xx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--0000.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--0000.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--00xx.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega8535 #------------------------------------------------------------ part desc = "ATmega8535"; id = "m8535"; prog_modes = PM_SPM | PM_ISP | PM_HVPP; mcuid = 161; n_interrupts = 21; stk500_devcode = 0x64; avr910_devcode = 0x69; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x93 0x08; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 20; blocksize = 128; readsize = 256; read = "1010.0000--00xx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxxa--aaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--0000.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--0000.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 2000; max_write_delay = 2000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--00xx.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny26 #------------------------------------------------------------ part desc = "ATtiny26"; id = "t26"; prog_modes = PM_ISP | PM_HVPP; mcuid = 17; n_interrupts = 12; stk500_devcode = 0x21; avr910_devcode = 0x5e; chip_erase_delay = 9000; pagel = 0xb3; bs2 = 0xb2; signature = 0x1e 0x91 0x09; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0xc4, 0xe4, 0xc4, 0xe4, 0xcc, 0xec, 0xcc, 0xec, 0xd4, 0xf4, 0xd4, 0xf4, 0xdc, 0xfc, 0xdc, 0xfc, 0xc8, 0xe8, 0xd8, 0xf8, 0x4c, 0x6c, 0x5c, 0x7c, 0xec, 0xbc, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 2; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 4; delay = 10; blocksize = 64; readsize = 256; read = "1010.0000--xxxx.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; ; memory "flash" paged = yes; size = 2048; page_size = 32; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 33; delay = 6; blocksize = 16; readsize = 256; read_lo = "0010.0000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxxx.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxxx.aaaa--iiii.iiii"; writepage = "0100.1100--xxxx.xxaa--aaaa.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--xxxi.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xxoo"; write = "1010.1100--1111.11ii--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; memory "calibration" size = 4; read = "0011.1000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny261 #------------------------------------------------------------ part desc = "ATtiny261"; id = "t261"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 30; n_interrupts = 19; chip_erase_delay = 4000; pagel = 0xb3; bs2 = 0xb2; # stk500_devcode = 0x21; # avr910_devcode = 0x5e; signature = 0x1e 0x91 0x0c; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0xc4, 0xe4, 0xc4, 0xe4, 0xcc, 0xec, 0xcc, 0xec, 0xd4, 0xf4, 0xd4, 0xf4, 0xdc, 0xfc, 0xdc, 0xfc, 0xc8, 0xe8, 0xd8, 0xf8, 0x4c, 0x6c, 0x5c, 0x7c, 0xec, 0xbc, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb4, 0x00, 0x10; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x00, 0xb4, 0x00, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 2; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; page_size = 4; num_pages = 32; min_write_delay = 4000; max_write_delay = 4000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 4; readsize = 256; read = "1010.0000--xxxx.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--xaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 2048; page_size = 32; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xxaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxxx.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxxx.aaaa--iiii.iiii"; writepage = "0100.1100--xxxx.xxaa--aaaa.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xxoo"; write = "1010.1100--1111.11ii--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny261A #------------------------------------------------------------ part parent "t261" desc = "ATtiny261A"; id = "t261a"; mcuid = 31; ; #------------------------------------------------------------ # ATtiny461 #------------------------------------------------------------ part desc = "ATtiny461"; id = "t461"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 33; n_interrupts = 19; chip_erase_delay = 4000; pagel = 0xb3; bs2 = 0xb2; # stk500_devcode = 0x21; # avr910_devcode = 0x5e; signature = 0x1e 0x92 0x08; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0xc4, 0xe4, 0xc4, 0xe4, 0xcc, 0xec, 0xcc, 0xec, 0xd4, 0xf4, 0xd4, 0xf4, 0xdc, 0xfc, 0xdc, 0xfc, 0xc8, 0xe8, 0xd8, 0xf8, 0x4c, 0x6c, 0x5c, 0x7c, 0xec, 0xbc, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb4, 0x00, 0x10; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x00, 0xb4, 0x00, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 2; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; page_size = 4; num_pages = 64; min_write_delay = 4000; max_write_delay = 4000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 4; readsize = 256; read = "1010.0000--xxxx.xxxx--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxx--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 4096; page_size = 64; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--xxxx.xaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xxoo"; write = "1010.1100--1111.11ii--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny461A #------------------------------------------------------------ part parent "t461" desc = "ATtiny461A"; id = "t461a"; mcuid = 34; ; #------------------------------------------------------------ # ATtiny861 #------------------------------------------------------------ part desc = "ATtiny861"; id = "t861"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 38; n_interrupts = 19; chip_erase_delay = 4000; pagel = 0xb3; bs2 = 0xb2; # stk500_devcode = 0x21; # avr910_devcode = 0x5e; signature = 0x1e 0x93 0x0d; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0xc4, 0xe4, 0xc4, 0xe4, 0xcc, 0xec, 0xcc, 0xec, 0xd4, 0xf4, 0xd4, 0xf4, 0xdc, 0xfc, 0xdc, 0xfc, 0xc8, 0xe8, 0xd8, 0xf8, 0x4c, 0x6c, 0x5c, 0x7c, 0xec, 0xbc, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb4, 0x00, 0x10; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x00, 0xb4, 0x00, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 2; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; num_pages = 128; min_write_delay = 4000; max_write_delay = 4000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 4; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--xxxx.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--xxxx.xxxx--xxxx.xxxx--xxxx.xxoo"; write = "1010.1100--1111.11ii--xxxx.xxxx--xxxx.xxxx"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--0000.00aa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny861A #------------------------------------------------------------ part parent "t861" desc = "ATtiny861A"; id = "t861a"; mcuid = 39; ; #------------------------------------------------------------ # ATtiny28 #------------------------------------------------------------ # This is an HVPP-only device. part desc = "ATtiny28"; id = "t28"; prog_modes = PM_HVPP; mcuid = 18; n_interrupts = 6; stk500_devcode = 0x22; avr910_devcode = 0x5c; signature = 0x1e 0x91 0x07; serial = no; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; memory "flash" size = 2048; page_size = 2; delay = 5; readsize = 256; ; memory "fuse" size = 1; ; memory "lock" size = 1; ; memory "signature" size = 3; ; memory "calibration" size = 1; ; ; #------------------------------------------------------------ # ATmega48 #------------------------------------------------------------ part desc = "ATmega48"; id = "m48"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 67; n_interrupts = 26; stk500_devcode = 0x59; chip_erase_delay = 45000; pagel = 0xd7; bs2 = 0xc2; # avr910_devcode = 0x??; signature = 0x1e 0x92 0x05; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 4096; page_size = 64; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.0aaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.0aaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.0aaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega48A #------------------------------------------------------------ part parent "m48" desc = "ATmega48A"; id = "m48a"; mcuid = 68; ; #------------------------------------------------------------ # ATmega48P #------------------------------------------------------------ part parent "m48" desc = "ATmega48P"; id = "m48p"; mcuid = 69; signature = 0x1e 0x92 0x0a; ; #------------------------------------------------------------ # ATmega48PA #------------------------------------------------------------ part parent "m48" desc = "ATmega48PA"; id = "m48pa"; mcuid = 70; signature = 0x1e 0x92 0x0a; ; #------------------------------------------------------------ # ATmega48PB #------------------------------------------------------------ part parent "m48" desc = "ATmega48PB"; id = "m48pb"; mcuid = 71; n_interrupts = 27; chip_erase_delay = 10500; signature = 0x1e 0x92 0x10; ; #------------------------------------------------------------ # ATmega88 #------------------------------------------------------------ part desc = "ATmega88"; id = "m88"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 79; n_interrupts = 26; stk500_devcode = 0x73; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc2; # avr910_devcode = 0x??; signature = 0x1e 0x93 0x0a; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega88A #------------------------------------------------------------ part parent "m88" desc = "ATmega88A"; id = "m88a"; mcuid = 80; ; #------------------------------------------------------------ # ATmega88P #------------------------------------------------------------ part parent "m88" desc = "ATmega88P"; id = "m88p"; mcuid = 81; signature = 0x1e 0x93 0x0f; ; #------------------------------------------------------------ # ATmega88PA #------------------------------------------------------------ part parent "m88" desc = "ATmega88PA"; id = "m88pa"; mcuid = 82; signature = 0x1e 0x93 0x0f; ; #------------------------------------------------------------ # ATmega88PB #------------------------------------------------------------ part parent "m88" desc = "ATmega88PB"; id = "m88pb"; mcuid = 83; n_interrupts = 27; chip_erase_delay = 10500; signature = 0x1e 0x93 0x16; ; #------------------------------------------------------------ # ATmega168 #------------------------------------------------------------ part desc = "ATmega168"; id = "m168"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 99; n_interrupts = 26; stk500_devcode = 0x86; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc2; # avr910_devcode = 0x??; signature = 0x1e 0x94 0x06; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--000a.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--000a.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--000a.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega168A #------------------------------------------------------------ part parent "m168" desc = "ATmega168A"; id = "m168a"; mcuid = 100; ; #------------------------------------------------------------ # ATmega168P #------------------------------------------------------------ part parent "m168" desc = "ATmega168P"; id = "m168p"; mcuid = 101; signature = 0x1e 0x94 0x0b; ; #------------------------------------------------------------ # ATmega168PA #------------------------------------------------------------ part parent "m168" desc = "ATmega168PA"; id = "m168pa"; mcuid = 102; signature = 0x1e 0x94 0x0b; ; #------------------------------------------------------------ # ATmega168PB #------------------------------------------------------------ part parent "m168" desc = "ATmega168PB"; id = "m168pb"; mcuid = 103; n_interrupts = 27; chip_erase_delay = 10500; signature = 0x1e 0x94 0x15; ; #------------------------------------------------------------ # ATtiny828 #------------------------------------------------------------ part desc = "ATtiny828"; id = "t828"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 35; n_interrupts = 26; stk500_devcode = 0x86; chip_erase_delay = 15000; pagel = 0xd7; bs2 = 0xc2; # avr910_devcode = 0x??; signature = 0x1e 0x93 0x14; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 5; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--111i.iiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny828R #------------------------------------------------------------ part parent "t828" desc = "ATtiny828R"; id = "t828r"; mcuid = 36; ; #------------------------------------------------------------ # ATtiny87 #------------------------------------------------------------ part desc = "ATtiny87"; id = "t87"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 27; n_interrupts = 20; # no STK500 devcode in XML file, use the ATtiny45 one stk500_devcode = 0x14; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 15000; signature = 0x1e 0x93 0x87; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0e, 0x1e, 0x2e, 0x3e, 0x2e, 0x3e, 0x4e, 0x5e, 0x4e, 0x5e, 0x6e, 0x7e, 0x6e, 0x7e, 0x06, 0x16, 0x46, 0x56, 0x0a, 0x1a, 0x4a, 0x5a, 0x1e, 0x7c, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 20; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; spmcr = 0x57; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 4; readsize = 256; read = "1010.0000--00xx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 128; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 64; readsize = 256; read_lo = "0010.0000--000a.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--000a.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--xxxx.xxii"; ; # ATtiny87 has Signature Bytes: 0x1E 0x93 0x87. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny167 #------------------------------------------------------------ part desc = "ATtiny167"; id = "t167"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 29; n_interrupts = 20; # no STK500 devcode in XML file, use the ATtiny45 one stk500_devcode = 0x14; # avr910_devcode = 0x??; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 15000; signature = 0x1e 0x94 0x87; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pp_controlstack = 0x0e, 0x1e, 0x0e, 0x1e, 0x2e, 0x3e, 0x2e, 0x3e, 0x4e, 0x5e, 0x4e, 0x5e, 0x6e, 0x7e, 0x6e, 0x7e, 0x06, 0x16, 0x46, 0x56, 0x0a, 0x1a, 0x4a, 0x5a, 0x1e, 0x7c, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 20; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; spmcr = 0x57; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 4; readsize = 256; read = "1010.0000--00xx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--00xx.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 64; readsize = 256; read_lo = "0010.0000--000a.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--000a.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--000a.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--xxxx.xxii"; ; # ATtiny167 has Signature Bytes: 0x1E 0x94 0x87. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny48 #------------------------------------------------------------ part desc = "ATtiny48"; id = "t48"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 23; n_interrupts = 20; stk500_devcode = 0x73; chip_erase_delay = 15000; pagel = 0xd7; bs2 = 0xc2; # avr910_devcode = 0x??; signature = 0x1e 0x92 0x09; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 64; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 64; read = "1010.0000--000x.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--xaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 4096; page_size = 64; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--1111.111i"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny88 #------------------------------------------------------------ part desc = "ATtiny88"; id = "t88"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 28; n_interrupts = 20; stk500_devcode = 0x73; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc2; # avr910_devcode = 0x??; signature = 0x1e 0x93 0x11; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 64; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 64; read = "1010.0000--000x.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--xaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega328 #------------------------------------------------------------ part desc = "ATmega328"; id = "m328"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 118; n_interrupts = 26; stk500_devcode = 0x86; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc2; # avr910_devcode = 0x??; signature = 0x1e 0x95 0x14; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 1024; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 128; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--00aa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega328P #------------------------------------------------------------ part parent "m328" desc = "ATmega328P"; id = "m328p"; mcuid = 119; signature = 0x1e 0x95 0x0f; ; #------------------------------------------------------------ # ATmega328PB #------------------------------------------------------------ part parent "m328" desc = "ATmega328PB"; id = "m328pb"; mcuid = 120; n_interrupts = 45; chip_erase_delay = 10500; signature = 0x1e 0x95 0x16; memory "efuse" write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; ; #------------------------------------------------------------ # ATmega32m1 #------------------------------------------------------------ part parent "m328" desc = "ATmega32M1"; id = "m32m1"; mcuid = 63; n_interrupts = 31; bs2 = 0xe2; # stk500_devcode = 0x??; # avr910_devcode = 0x??; signature = 0x1e 0x95 0x84; memory "efuse" write = "1010.1100--1010.0100--xxxx.xxxx--xxii.iiii"; ; ; #------------------------------------------------------------ # ATmega64m1 #------------------------------------------------------------ part parent "m328" desc = "ATmega64M1"; id = "m64m1"; mcuid = 76; n_interrupts = 31; bs2 = 0xe2; # stk500_devcode = 0x??; # avr910_devcode = 0x??; signature = 0x1e 0x96 0x84; memory "eeprom" size = 2048; page_size = 8; read = "1010.0000--000x.xaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.xaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" size = 0x10000; page_size = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "efuse" write = "1010.1100--1010.0100--xxxx.xxxx--xxii.iiii"; ; ; #------------------------------------------------------------ # ATtiny2313 #------------------------------------------------------------ part desc = "ATtiny2313"; id = "t2313"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 42; n_interrupts = 19; stk500_devcode = 0x23; # Use the ATtiny26 devcode: avr910_devcode = 0x5e; chip_erase_delay = 9000; pagel = 0xd4; bs2 = 0xd6; signature = 0x1e 0x91 0x0a; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0e, 0x1e, 0x2e, 0x3e, 0x2e, 0x3e, 0x4e, 0x5e, 0x4e, 0x5e, 0x6e, 0x7e, 0x6e, 0x7e, 0x26, 0x36, 0x66, 0x76, 0x2a, 0x3a, 0x6a, 0x7a, 0x2e, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb2, 0x0f, 0x1f; eeprom_instr = 0xbb, 0xfe, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xba, 0x0f, 0xb2, 0x0f, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 0; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--xaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 2048; page_size = 32; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.00aa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.00aa--aaaa.aaaa--oooo.oooo"; # The information in the data sheet of April/2004 is wrong, this works: loadpage_lo = "0100.0000--000x.xxxx--xxxx.aaaa--iiii.iiii"; # The information in the data sheet of April/2004 is wrong, this works: loadpage_hi = "0100.1000--000x.xxxx--xxxx.aaaa--iiii.iiii"; # The information in the data sheet of April/2004 is wrong, this works: writepage = "0100.1100--0000.00aa--aaaa.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; # ATtiny2313 has Signature Bytes: 0x1E 0x91 0x0A. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; # The Tiny2313 has calibration data for both 4 MHz and 8 MHz. # The information in the data sheet of April/2004 is wrong, this works: memory "calibration" size = 2; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny2313A #------------------------------------------------------------ part parent "t2313" desc = "ATtiny2313A"; id = "t2313a"; mcuid = 43; n_interrupts = 21; ; #------------------------------------------------------------ # ATtiny4313 #------------------------------------------------------------ part desc = "ATtiny4313"; id = "t4313"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 44; n_interrupts = 21; stk500_devcode = 0x23; # Use the ATtiny26 devcode: avr910_devcode = 0x5e; chip_erase_delay = 9000; pagel = 0xd4; bs2 = 0xd6; signature = 0x1e 0x92 0x0d; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0e, 0x1e, 0x2e, 0x3e, 0x2e, 0x3e, 0x4e, 0x5e, 0x4e, 0x5e, 0x6e, 0x7e, 0x6e, 0x7e, 0x26, 0x36, 0x66, 0x76, 0x2a, 0x3a, 0x6a, 0x7a, 0x2e, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb2, 0x0f, 0x1f; eeprom_instr = 0xbb, 0xfe, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xba, 0x0f, 0xb2, 0x0f, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 0; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 4096; page_size = 64; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.0aaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.0aaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.0aaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; # ATtiny4313 has Signature Bytes: 0x1E 0x92 0x0D. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 2; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90PWM2 #------------------------------------------------------------ part desc = "AT90PWM2"; id = "pwm2"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 167; n_interrupts = 32; stk500_devcode = 0x65; chip_erase_delay = 9000; pagel = 0xd8; bs2 = 0xe2; # avr910_devcode = ?; signature = 0x1e 0x93 0x81; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; # AT90PWM2 has Signature Bytes: 0x1E 0x93 0x81. memory "signature" size = 3; read = "0011.0000--00xx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90PWM3 #------------------------------------------------------------ # Completely identical to AT90PWM2 (including the signature!) part parent "pwm2" desc = "AT90PWM3"; id = "pwm3"; mcuid = 169; ; #------------------------------------------------------------ # AT90PWM2B #------------------------------------------------------------ # Same as AT90PWM2 but different signature. part parent "pwm2" desc = "AT90PWM2B"; id = "pwm2b"; mcuid = 168; signature = 0x1e 0x93 0x83; ocdrev = 1; ; #------------------------------------------------------------ # AT90PWM3B #------------------------------------------------------------ # Completely identical to AT90PWM2B (including the signature!) part parent "pwm2b" desc = "AT90PWM3B"; id = "pwm3b"; mcuid = 170; ; #------------------------------------------------------------ # AT90PWM316 #------------------------------------------------------------ # Similar to AT90PWM3B, but with 16 kiB flash, 512 B EEPROM, and 1024 B SRAM. part parent "pwm3b" desc = "AT90PWM316"; id = "pwm316"; mcuid = 180; signature = 0x1e 0x94 0x83; memory "flash" size = 0x4000; page_size = 128; mode = 33; blocksize = 128; read_lo = "0010.0000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--00xx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--00aa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; ; #------------------------------------------------------------ # AT90PWM216 #------------------------------------------------------------ # Completely identical to AT90PWM316 (including the signature!) part parent "pwm316" desc = "AT90PWM216"; id = "pwm216"; mcuid = 179; ; #------------------------------------------------------------ # ATtiny25 #------------------------------------------------------------ part desc = "ATtiny25"; id = "t25"; prog_modes = PM_SPM | PM_ISP | PM_HVSP | PM_debugWIRE; mcuid = 16; n_interrupts = 15; # no STK500 devcode in XML file, use the ATtiny45 one stk500_devcode = 0x14; # avr910_devcode = ?; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 4500; signature = 0x1e 0x91 0x08; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x66, 0x68, 0x78, 0x68, 0x68, 0x7a, 0x6a, 0x68, 0x78, 0x78, 0x7d, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; flash_instr = 0xb4, 0x02, 0x12; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x02, 0xb4, 0x02, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayms = 1; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--xaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 2048; page_size = 32; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.00aa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.00aa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxx.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxx.aaaa--iiii.iiii"; writepage = "0100.1100--0000.00aa--aaaa.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; # ATtiny25 has Signature Bytes: 0x1E 0x91 0x08. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny45 #------------------------------------------------------------ part desc = "ATtiny45"; id = "t45"; prog_modes = PM_SPM | PM_ISP | PM_HVSP | PM_debugWIRE; mcuid = 22; n_interrupts = 15; stk500_devcode = 0x14; # avr910_devcode = ?; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 4500; signature = 0x1e 0x92 0x06; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x66, 0x68, 0x78, 0x68, 0x68, 0x7a, 0x6a, 0x68, 0x78, 0x78, 0x7d, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; flash_instr = 0xb4, 0x02, 0x12; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x02, 0xb4, 0x02, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayms = 1; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 4096; page_size = 64; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.0aaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.0aaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.0aaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; # ATtiny45 has Signature Bytes: 0x1E 0x92 0x08. (Data sheet 2586C-AVR-06/05 (doc2586.pdf) indicates otherwise!) memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny85 #------------------------------------------------------------ part desc = "ATtiny85"; id = "t85"; prog_modes = PM_SPM | PM_ISP | PM_HVSP | PM_debugWIRE; mcuid = 26; n_interrupts = 15; # no STK500 devcode in XML file, use the ATtiny45 one stk500_devcode = 0x14; # avr910_devcode = ?; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 4500; signature = 0x1e 0x93 0x0b; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x66, 0x68, 0x78, 0x68, 0x68, 0x7a, 0x6a, 0x68, 0x78, 0x78, 0x7d, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00; flash_instr = 0xb4, 0x02, 0x12; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x02, 0xb4, 0x02, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayms = 1; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; # ATtiny85 has Signature Bytes: 0x1E 0x93 0x08. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega640 #------------------------------------------------------------ # Almost same as ATmega1280, except for different memory sizes part desc = "ATmega640"; id = "m640"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 126; n_interrupts = 57; # stk500_devcode = 0xB2; # avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x96 0x08; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 10; blocksize = 8; readsize = 256; read = "1010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.aaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x10000; page_size = 256; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 10; blocksize = 256; readsize = 256; read_lo = "0010.0000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--0aaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega1280 #------------------------------------------------------------ part desc = "ATmega1280"; id = "m1280"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 138; n_interrupts = 57; # stk500_devcode = 0xB2; # avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x97 0x03; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 10; blocksize = 8; readsize = 256; read = "1010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.aaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x20000; page_size = 256; num_pages = 512; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 10; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega1281 #------------------------------------------------------------ # Identical to ATmega1280 part parent "m1280" desc = "ATmega1281"; id = "m1281"; mcuid = 139; n_interrupts = 51; signature = 0x1e 0x97 0x04; ; #------------------------------------------------------------ # ATmega2560 #------------------------------------------------------------ part desc = "ATmega2560"; id = "m2560"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 143; n_interrupts = 57; stk500_devcode = 0xb2; # avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x98 0x01; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; ocdrev = 4; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 10; blocksize = 8; readsize = 256; read = "1010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.aaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x40000; page_size = 256; num_pages = 1024; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 10; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; load_ext_addr = "0100.1101--0000.0000--0000.000a--0000.0000"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega2561 #------------------------------------------------------------ part parent "m2560" desc = "ATmega2561"; id = "m2561"; mcuid = 144; n_interrupts = 51; signature = 0x1e 0x98 0x02; ; #------------------------------------------------------------ # ATmega128RFA1 #------------------------------------------------------------ # Identical to ATmega2561 but half the ROM part parent "m2561" desc = "ATmega128RFA1"; id = "m128rfa1"; mcuid = 87; n_interrupts = 72; chip_erase_delay = 55000; bs2 = 0xe2; signature = 0x1e 0xa7 0x01; ocdrev = 3; memory "flash" size = 0x20000; num_pages = 512; min_write_delay = 50000; max_write_delay = 50000; delay = 20; load_ext_addr = NULL; ; ; #------------------------------------------------------------ # ATmega256RFR2 #------------------------------------------------------------ part parent "m2561" desc = "ATmega256RFR2"; id = "m256rfr2"; mcuid = 108; n_interrupts = 77; chip_erase_delay = 18500; bs2 = 0xe2; signature = 0x1e 0xa8 0x02; memory "eeprom" size = 8192; min_write_delay = 13000; max_write_delay = 13000; read = "1010.0000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxa.aaaa--aaaa.aaaa--iiii.iiii"; writepage = "1100.0010--00xa.aaaa--aaaa.a000--xxxx.xxxx"; ; ; #------------------------------------------------------------ # ATmega128RFR2 #------------------------------------------------------------ part parent "m128rfa1" desc = "ATmega128RFR2"; id = "m128rfr2"; mcuid = 88; n_interrupts = 77; signature = 0x1e 0xa7 0x02; ; #------------------------------------------------------------ # ATmega64RFR2 #------------------------------------------------------------ part parent "m128rfa1" desc = "ATmega64RFR2"; id = "m64rfr2"; mcuid = 78; n_interrupts = 77; signature = 0x1e 0xa6 0x02; memory "eeprom" size = 2048; min_write_delay = 13000; max_write_delay = 13000; read = "1010.0000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; writepage = "1100.0010--00xx.xaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" size = 0x10000; num_pages = 256; read_lo = "0010.0000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; writepage = "0100.1100--0aaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; ; #------------------------------------------------------------ # ATmega2564RFR2 #------------------------------------------------------------ part parent "m256rfr2" desc = "ATmega2564RFR2"; id = "m2564rfr2"; mcuid = 145; signature = 0x1e 0xa8 0x03; ; #------------------------------------------------------------ # ATmega1284RFR2 #------------------------------------------------------------ part parent "m128rfr2" desc = "ATmega1284RFR2"; id = "m1284rfr2"; mcuid = 142; signature = 0x1e 0xa7 0x03; ; #------------------------------------------------------------ # ATmega644RFR2 #------------------------------------------------------------ part parent "m64rfr2" desc = "ATmega644RFR2"; id = "m644rfr2"; mcuid = 131; signature = 0x1e 0xa6 0x03; ; #------------------------------------------------------------ # ATtiny24 #------------------------------------------------------------ part desc = "ATtiny24"; id = "t24"; prog_modes = PM_SPM | PM_ISP | PM_HVSP | PM_debugWIRE; mcuid = 14; n_interrupts = 17; # no STK500 devcode in XML file, use the ATtiny45 one stk500_devcode = 0x14; # avr910_devcode = ?; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 4500; signature = 0x1e 0x91 0x0b; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x66, 0x68, 0x78, 0x68, 0x68, 0x7a, 0x6a, 0x68, 0x78, 0x78, 0x7d, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x0f; flash_instr = 0xb4, 0x07, 0x17; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x07, 0xb4, 0x07, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayus = 70; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 128; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--xaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--xaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 2048; page_size = 32; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.00aa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.00aa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxx.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxx.aaaa--iiii.iiii"; writepage = "0100.1100--0000.00aa--aaaa.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--xxxx.xxii"; ; # ATtiny24 has Signature Bytes: 0x1E 0x91 0x0B. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny24A #------------------------------------------------------------ part parent "t24" desc = "ATtiny24A"; id = "t24a"; mcuid = 15; ; #------------------------------------------------------------ # ATtiny44 #------------------------------------------------------------ part desc = "ATtiny44"; id = "t44"; prog_modes = PM_SPM | PM_ISP | PM_HVSP | PM_debugWIRE; mcuid = 20; n_interrupts = 17; # no STK500 devcode in XML file, use the ATtiny45 one stk500_devcode = 0x14; # avr910_devcode = ?; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 4500; signature = 0x1e 0x92 0x07; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x66, 0x68, 0x78, 0x68, 0x68, 0x7a, 0x6a, 0x68, 0x78, 0x78, 0x7d, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x0f; flash_instr = 0xb4, 0x07, 0x17; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x07, 0xb4, 0x07, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayus = 70; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 4096; page_size = 64; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.0aaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.0aaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.0aaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--xxxx.xxii"; ; # ATtiny44 has Signature Bytes: 0x1E 0x92 0x07. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny44A #------------------------------------------------------------ part parent "t44" desc = "ATtiny44A"; id = "t44a"; mcuid = 21; ; #------------------------------------------------------------ # ATtiny84 #------------------------------------------------------------ part desc = "ATtiny84"; id = "t84"; prog_modes = PM_SPM | PM_ISP | PM_HVSP | PM_debugWIRE; mcuid = 24; n_interrupts = 17; # no STK500 devcode in XML file, use the ATtiny45 one stk500_devcode = 0x14; # avr910_devcode = ?; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 4500; signature = 0x1e 0x93 0x0c; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; hvsp_controlstack = 0x4c, 0x0c, 0x1c, 0x2c, 0x3c, 0x64, 0x74, 0x66, 0x68, 0x78, 0x68, 0x68, 0x7a, 0x6a, 0x68, 0x78, 0x78, 0x7d, 0x6d, 0x0c, 0x80, 0x40, 0x20, 0x10, 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x0f; flash_instr = 0xb4, 0x07, 0x17; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x07, 0xb4, 0x07, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 1; togglevtg = 1; poweroffdelay = 25; resetdelayus = 70; hvleavestabdelay = 100; resetdelay = 25; chiperasepolltimeout = 40; programfusepolltimeout = 25; programlockpolltimeout = 25; synchcycles = 6; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 64; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 32; readsize = 256; read_lo = "0010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--xxxx.xxii"; ; # ATtiny84 has Signature Bytes: 0x1E 0x93 0x0C. memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny84A #------------------------------------------------------------ part parent "t84" desc = "ATtiny84A"; id = "t84a"; mcuid = 25; ; #------------------------------------------------------------ # ATtiny441 #------------------------------------------------------------ part parent "t44" desc = "ATtiny441"; id = "t441"; mcuid = 32; n_interrupts = 30; n_page_erase = 4; signature = 0x1e 0x92 0x15; memory "flash" page_size = 16; num_pages = 256; blocksize = 16; loadpage_lo = "0100.0000--000x.xxxx--xxxx.xaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxx.xaaa--iiii.iiii"; writepage = "0100.1100--0000.0aaa--aaaa.axxx--xxxx.xxxx"; ; memory "efuse" write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; ; #------------------------------------------------------------ # ATtiny841 #------------------------------------------------------------ part parent "t84" desc = "ATtiny841"; id = "t841"; mcuid = 37; n_interrupts = 30; n_page_erase = 4; signature = 0x1e 0x93 0x15; memory "flash" page_size = 16; num_pages = 512; blocksize = 16; loadpage_lo = "0100.0000--000x.xxxx--xxxx.xaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxx.xaaa--iiii.iiii"; writepage = "0100.1100--0000.aaaa--aaaa.axxx--xxxx.xxxx"; ; memory "efuse" write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; ; #------------------------------------------------------------ # ATtiny43U #------------------------------------------------------------ part desc = "ATtiny43U"; id = "t43u"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 19; n_interrupts = 16; stk500_devcode = 0x14; # avr910_devcode = ?; # Try the AT90S2313 devcode: avr910_devcode = 0x20; chip_erase_delay = 1000; signature = 0x1e 0x92 0x0c; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0e, 0x1e, 0x2e, 0x3e, 0x2e, 0x3e, 0x4e, 0x5e, 0x4e, 0x5e, 0x6e, 0x7e, 0x6e, 0x7e, 0x06, 0x16, 0x46, 0x56, 0x0a, 0x1a, 0x4a, 0x5a, 0x1e, 0x7c, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb4, 0x07, 0x17; eeprom_instr = 0xbb, 0xff, 0xbb, 0xee, 0xbb, 0xcc, 0xb2, 0x0d, 0xbc, 0x07, 0xb4, 0x07, 0xba, 0x0d, 0xbb, 0xbc, 0x99, 0xe1, 0xbb, 0xac; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 20; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" paged = yes; size = 64; page_size = 4; num_pages = 16; min_write_delay = 4000; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 5; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxx--00aa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxx--00aa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxx--00aa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 4096; page_size = 64; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 64; readsize = 256; read_lo = "0010.0000--0000.0aaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0000.0aaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxa.aaaa--iiii.iiii"; writepage = "0100.1100--0000.0aaa--aaax.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.xxxi"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.000a--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega16u4 #------------------------------------------------------------ part desc = "ATmega16U4"; id = "m16u4"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 57; n_interrupts = 43; # stk500_devcode = 0xB2; # avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x94 0x88; usbpid = 0x2ff4; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--xxxx.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--1111.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--00oo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega32u4 #------------------------------------------------------------ part desc = "ATmega32U4"; id = "m32u4"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 65; n_interrupts = 43; # stk500_devcode = 0xB2; # avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x95 0x87; usbpid = 0x2ff4; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 1024; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xaaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 128; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--1111.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90USB646 #------------------------------------------------------------ part desc = "AT90USB646"; id = "usb646"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 181; n_interrupts = 38; # stk500_devcode = 0xB2; # avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x96 0x82; usbpid = 0x2ff9; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 2048; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 10; blocksize = 8; readsize = 256; read = "1010.0000--xxxx.xaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.xaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.xaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x10000; page_size = 256; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--0aaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90USB647 #------------------------------------------------------------ # identical to AT90USB646 part parent "usb646" desc = "AT90USB647"; id = "usb647"; mcuid = 182; ; #------------------------------------------------------------ # AT90USB1286 #------------------------------------------------------------ part desc = "AT90USB1286"; id = "usb1286"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 184; n_interrupts = 38; # stk500_devcode = 0xB2; # avr910_devcode = 0x43; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x97 0x82; usbpid = 0x2ffb; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; rampz = 0x3b; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 4096; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 10; blocksize = 8; readsize = 256; read = "1010.0000--xxxx.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--xxxx.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--00xx.aaaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x20000; page_size = 256; num_pages = 512; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 256; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--axxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--xxxx.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--xxxx.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90USB1287 #------------------------------------------------------------ # identical to AT90USB1286 part parent "usb1286" desc = "AT90USB1287"; id = "usb1287"; mcuid = 185; ; #------------------------------------------------------------ # AT90USB162 #------------------------------------------------------------ part desc = "AT90USB162"; id = "usb162"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 178; n_interrupts = 29; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc6; signature = 0x1e 0x94 0x82; usbpid = 0x2ffa; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; num_pages = 128; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--0000.aaaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # AT90USB82 #------------------------------------------------------------ part desc = "AT90USB82"; id = "usb82"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 174; n_interrupts = 58; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc6; signature = 0x1e 0x93 0x82; usbpid = 0x2ff7; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; num_pages = 128; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--0000.aaaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 128; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega32U2 #------------------------------------------------------------ part desc = "ATmega32U2"; id = "m32u2"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 64; n_interrupts = 29; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc6; signature = 0x1e 0x95 0x8a; usbpid = 0x2ff0; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 1024; page_size = 4; num_pages = 256; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--0000.aaaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 128; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega16U2 #------------------------------------------------------------ part desc = "ATmega16U2"; id = "m16u2"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 56; n_interrupts = 29; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc6; signature = 0x1e 0x94 0x89; usbpid = 0x2fef; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; num_pages = 128; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--0000.aaaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega8U2 #------------------------------------------------------------ part desc = "ATmega8U2"; id = "m8u2"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 48; n_interrupts = 58; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xc6; signature = 0x1e 0x93 0x89; usbpid = 0x2fee; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; ocdrev = 1; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; num_pages = 128; min_write_delay = 9000; max_write_delay = 9000; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--0000.aaaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.aaaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--0000.aaaa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 8192; page_size = 128; num_pages = 64; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--xxxx.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--iiii.iiii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega165 #------------------------------------------------------------ part desc = "ATmega165"; id = "m165"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 95; n_interrupts = 22; # stk500_devcode = 0x??; # avr910_devcode = 0x??; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x94 0x10; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 6; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; eecr = 0x3f; ocdrev = 3; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 512; page_size = 4; num_pages = 128; min_write_delay = 3600; max_write_delay = 3600; mode = 65; delay = 20; blocksize = 4; readsize = 256; read = "1010.0000--0000.00xa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.00xa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--0000.00xa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 128; num_pages = 128; min_write_delay = 4500; max_write_delay = 4500; mode = 65; delay = 10; blocksize = 128; readsize = 256; read_lo = "0010.0000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--xxxa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--0000.xxxx--xxaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--0000.xxxx--xxaa.aaaa--iiii.iiii"; writepage = "0100.1100--xxxa.aaaa--aaxx.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxx.iiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--0000.0000--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--0000.0000--xxxx.xxxx--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega165A #------------------------------------------------------------ part parent "m165" desc = "ATmega165A"; id = "m165a"; mcuid = 96; ; #------------------------------------------------------------ # ATmega165P #------------------------------------------------------------ part parent "m165" desc = "ATmega165P"; id = "m165p"; mcuid = 97; signature = 0x1e 0x94 0x07; ; #------------------------------------------------------------ # ATmega165PA #------------------------------------------------------------ part parent "m165" desc = "ATmega165PA"; id = "m165pa"; mcuid = 98; signature = 0x1e 0x94 0x07; ; #------------------------------------------------------------ # ATmega325 #------------------------------------------------------------ part desc = "ATmega325"; id = "m325"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 114; n_interrupts = 23; # stk500_devcode = 0x??; # No STK500v1 support? # avr910_devcode = 0x??; # Try the ATmega16 one avr910_devcode = 0x74; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x95 0x05; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--0000.0000--0000.0000"; pgm_enable = "1010.1100--0101.0011--0000.0000--0000.0000"; memory "eeprom" size = 1024; page_size = 4; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 4; readsize = 256; read = "1010.0000--0000.00aa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.00aa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--0000.00aa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x8000; page_size = 128; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 128; readsize = 256; read_lo = "0010.0000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--0aaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--0000.0000--aaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--0000.0000--aaaa.aaaa--iiii.iiii"; writepage = "0100.1100--0aaa.aaaa--aaaa.aaaa--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--1010.0000--0000.0000--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--0000.0000--oooo.oooo"; write = "1010.1100--1010.1000--0000.0000--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--0000.0000--oooo.oooo"; write = "1010.1100--1010.0100--0000.0000--1111.1iii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1110.0000--0000.0000--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--0000.0000--0000.00aa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--0000.0000--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega325A #------------------------------------------------------------ part parent "m325" desc = "ATmega325A"; id = "m325a"; mcuid = 115; ; #------------------------------------------------------------ # ATmega325P #------------------------------------------------------------ part parent "m325" desc = "ATmega325P"; id = "m325p"; mcuid = 116; signature = 0x1e 0x95 0x0d; ; #------------------------------------------------------------ # ATmega325PA #------------------------------------------------------------ part parent "m325" desc = "ATmega325PA"; id = "m325pa"; mcuid = 117; n_interrupts = 22; signature = 0x1e 0x95 0x0d; ; #------------------------------------------------------------ # ATmega645 #------------------------------------------------------------ part desc = "ATmega645"; id = "m645"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_JTAG; mcuid = 132; n_interrupts = 23; # stk500_devcode = 0x??; # No STK500v1 support? # avr910_devcode = 0x??; # Try the ATmega16 one avr910_devcode = 0x74; chip_erase_delay = 9000; pagel = 0xd7; bs2 = 0xa0; signature = 0x1e 0x96 0x05; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; hventerstabdelay = 100; latchcycles = 5; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; idr = 0x31; spmcr = 0x57; ocdrev = 3; chip_erase = "1010.1100--1000.0000--0000.0000--0000.0000"; pgm_enable = "1010.1100--0101.0011--0000.0000--0000.0000"; memory "eeprom" size = 2048; page_size = 8; min_write_delay = 9000; max_write_delay = 9000; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 8; readsize = 256; read = "1010.0000--0000.0aaa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--0000.0aaa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.0aaa--iiii.iiii"; writepage = "1100.0010--0000.0aaa--aaaa.a000--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x10000; page_size = 256; num_pages = 256; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 10; blocksize = 128; readsize = 256; read_lo = "0010.0000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--aaaa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--0000.0000--aaaa.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--0000.0000--aaaa.aaaa--iiii.iiii"; writepage = "0100.1100--aaaa.aaaa--aaaa.aaaa--0000.0000"; ; memory "lfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.0000--0000.0000--oooo.oooo"; write = "1010.1100--1010.0000--0000.0000--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.1000--0000.0000--oooo.oooo"; write = "1010.1100--1010.1000--0000.0000--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.0000--0000.1000--0000.0000--oooo.oooo"; write = "1010.1100--1010.0100--0000.0000--1111.1iii"; ; memory "lock" size = 1; min_write_delay = 9000; max_write_delay = 9000; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1110.0000--0000.0000--11ii.iiii"; ; memory "signature" size = 3; read = "0011.0000--0000.0000--0000.00aa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--0000.0000--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATmega645A #------------------------------------------------------------ part parent "m645" desc = "ATmega645A"; id = "m645a"; mcuid = 133; ; #------------------------------------------------------------ # ATmega645P #------------------------------------------------------------ part parent "m645" desc = "ATmega645P"; id = "m645p"; mcuid = 134; signature = 0x1e 0x96 0x0d; ; #------------------------------------------------------------ # ATmega3250 #------------------------------------------------------------ part parent "m325" desc = "ATmega3250"; id = "m3250"; mcuid = 146; n_interrupts = 25; signature = 0x1e 0x95 0x06; ; #------------------------------------------------------------ # ATmega3250A #------------------------------------------------------------ part parent "m325" desc = "ATmega3250A"; id = "m3250a"; mcuid = 147; n_interrupts = 25; signature = 0x1e 0x95 0x06; ; #------------------------------------------------------------ # ATmega3250P #------------------------------------------------------------ part parent "m325" desc = "ATmega3250P"; id = "m3250p"; mcuid = 148; n_interrupts = 25; signature = 0x1e 0x95 0x0e; ; #------------------------------------------------------------ # ATmega3250PA #------------------------------------------------------------ part parent "m325" desc = "ATmega3250PA"; id = "m3250pa"; mcuid = 149; n_interrupts = 25; signature = 0x1e 0x95 0x0e; ; #------------------------------------------------------------ # ATmega6450 #------------------------------------------------------------ part parent "m645" desc = "ATmega6450"; id = "m6450"; mcuid = 154; n_interrupts = 25; signature = 0x1e 0x96 0x06; ; #------------------------------------------------------------ # ATmega6450A #------------------------------------------------------------ part parent "m645" desc = "ATmega6450A"; id = "m6450a"; mcuid = 155; n_interrupts = 25; signature = 0x1e 0x96 0x06; ; #------------------------------------------------------------ # ATmega6450P #------------------------------------------------------------ part parent "m645" desc = "ATmega6450P"; id = "m6450p"; mcuid = 156; n_interrupts = 25; signature = 0x1e 0x96 0x0e; ; #------------------------------------------------------------ # AVR XMEGA family common values #------------------------------------------------------------ part desc = "AVR XMEGA family common values"; id = ".xmega"; prog_modes = PM_SPM | PM_PDI; mcu_base = 0x0090; nvm_base = 0x01c0; memory "fuse1" size = 1; offset = 0x8f0021; ; memory "fuse2" size = 1; offset = 0x8f0022; ; memory "fuse4" size = 1; offset = 0x8f0024; ; memory "fuse5" size = 1; offset = 0x8f0025; ; memory "lock" size = 1; offset = 0x8f0027; ; memory "signature" size = 3; offset = 0x1000090; ; memory "prodsig" size = 50; page_size = 50; offset = 0x8e0200; readsize = 50; ; memory "data" # SRAM, only used to supply the offset offset = 0x1000000; ; ; #------------------------------------------------------------ # ATxmega16A4U #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega16A4U"; id = "x16a4u"; mcuid = 232; n_interrupts = 127; signature = 0x1e 0x94 0x41; usbpid = 0x2fe3; memory "eeprom" size = 1024; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x5000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "application" size = 0x4000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "apptable" size = 4096; page_size = 256; offset = 0x803000; readsize = 256; ; memory "boot" size = 4096; page_size = 256; offset = 0x804000; readsize = 256; ; memory "usersig" size = 256; page_size = 256; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega16C4 #------------------------------------------------------------ part parent "x16a4u" desc = "ATxmega16C4"; id = "x16c4"; mcuid = 233; signature = 0x1e 0x94 0x43; ; #------------------------------------------------------------ # ATxmega16D4 #------------------------------------------------------------ part parent "x16a4u" desc = "ATxmega16D4"; id = "x16d4"; mcuid = 234; n_interrupts = 91; signature = 0x1e 0x94 0x42; ; #------------------------------------------------------------ # ATxmega16A4 #------------------------------------------------------------ part parent "x16a4u" desc = "ATxmega16A4"; id = "x16a4"; mcuid = 231; n_interrupts = 94; memory "fuse0" size = 1; offset = 0x8f0020; ; ; #------------------------------------------------------------ # ATxmega32A4U #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega32A4U"; id = "x32a4u"; mcuid = 239; n_interrupts = 127; signature = 0x1e 0x95 0x41; usbpid = 0x2fe4; memory "eeprom" size = 1024; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x9000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "application" size = 0x8000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "apptable" size = 4096; page_size = 256; offset = 0x807000; readsize = 256; ; memory "boot" size = 4096; page_size = 256; offset = 0x808000; readsize = 256; ; memory "usersig" size = 256; page_size = 256; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega32C4 #------------------------------------------------------------ part parent "x32a4u" desc = "ATxmega32C4"; id = "x32c4"; mcuid = 240; signature = 0x1e 0x95 0x44; ; #------------------------------------------------------------ # ATxmega32D4 #------------------------------------------------------------ part parent "x32a4u" desc = "ATxmega32D4"; id = "x32d4"; mcuid = 241; n_interrupts = 91; signature = 0x1e 0x95 0x42; ; #------------------------------------------------------------ # ATxmega32A4 #------------------------------------------------------------ part parent "x32a4u" desc = "ATxmega32A4"; id = "x32a4"; mcuid = 238; n_interrupts = 94; memory "fuse0" size = 1; offset = 0x8f0020; ; ; #------------------------------------------------------------ # ATxmega64A4U #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega64A4U"; id = "x64a4u"; mcuid = 252; n_interrupts = 127; signature = 0x1e 0x96 0x46; usbpid = 0x2fe5; memory "eeprom" size = 2048; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x11000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "application" size = 0x10000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "apptable" size = 4096; page_size = 256; offset = 0x80f000; readsize = 256; ; memory "boot" size = 4096; page_size = 256; offset = 0x810000; readsize = 256; ; memory "usersig" size = 256; page_size = 256; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega64C3 #------------------------------------------------------------ part parent "x64a4u" desc = "ATxmega64C3"; id = "x64c3"; mcuid = 249; signature = 0x1e 0x96 0x49; usbpid = 0x2fd6; ; #------------------------------------------------------------ # ATxmega64D3 #------------------------------------------------------------ part parent "x64a4u" desc = "ATxmega64D3"; id = "x64d3"; mcuid = 250; n_interrupts = 114; signature = 0x1e 0x96 0x4a; ; #------------------------------------------------------------ # ATxmega64D4 #------------------------------------------------------------ part parent "x64a4u" desc = "ATxmega64D4"; id = "x64d4"; mcuid = 253; n_interrupts = 91; signature = 0x1e 0x96 0x47; ; #------------------------------------------------------------ # ATxmega64A1 #------------------------------------------------------------ part parent "x64a4u" desc = "ATxmega64A1"; id = "x64a1"; prog_modes = PM_SPM | PM_PDI | PM_XMEGAJTAG; mcuid = 243; n_interrupts = 125; signature = 0x1e 0x96 0x4e; memory "fuse0" size = 1; offset = 0x8f0020; ; ; #------------------------------------------------------------ # ATxmega64A1U #------------------------------------------------------------ part parent "x64a1" desc = "ATxmega64A1U"; id = "x64a1u"; mcuid = 244; n_interrupts = 127; usbpid = 0x2fe8; ; #------------------------------------------------------------ # ATxmega64A3 #------------------------------------------------------------ part parent "x64a1" desc = "ATxmega64A3"; id = "x64a3"; mcuid = 246; n_interrupts = 122; signature = 0x1e 0x96 0x42; ; #------------------------------------------------------------ # ATxmega64A3U #------------------------------------------------------------ part parent "x64a1" desc = "ATxmega64A3U"; id = "x64a3u"; mcuid = 247; n_interrupts = 127; signature = 0x1e 0x96 0x42; ; #------------------------------------------------------------ # ATxmega64A4 #------------------------------------------------------------ part parent "x64a1" desc = "ATxmega64A4"; id = "x64a4"; mcuid = 251; signature = 0x1e 0x96 0x46; ; #------------------------------------------------------------ # ATxmega64B1 #------------------------------------------------------------ part parent "x64a1" desc = "ATxmega64B1"; id = "x64b1"; mcuid = 245; n_interrupts = 81; signature = 0x1e 0x96 0x52; usbpid = 0x2fe1; ; #------------------------------------------------------------ # ATxmega64B3 #------------------------------------------------------------ part parent "x64a1" desc = "ATxmega64B3"; id = "x64b3"; mcuid = 248; n_interrupts = 54; signature = 0x1e 0x96 0x51; usbpid = 0x2fdf; ; #------------------------------------------------------------ # ATxmega128C3 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega128C3"; id = "x128c3"; mcuid = 261; n_interrupts = 127; signature = 0x1e 0x97 0x52; usbpid = 0x2fd7; memory "eeprom" size = 2048; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x22000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "application" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "apptable" size = 8192; page_size = 512; offset = 0x81e000; readsize = 256; ; memory "boot" size = 8192; page_size = 512; offset = 0x820000; readsize = 256; ; memory "usersig" size = 512; page_size = 512; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega128D3 #------------------------------------------------------------ part parent "x128c3" desc = "ATxmega128D3"; id = "x128d3"; mcuid = 262; n_interrupts = 114; signature = 0x1e 0x97 0x48; ; #------------------------------------------------------------ # ATxmega128D4 #------------------------------------------------------------ part parent "x128c3" desc = "ATxmega128D4"; id = "x128d4"; mcuid = 265; n_interrupts = 91; signature = 0x1e 0x97 0x47; memory "flash" page_size = 256; ; ; #------------------------------------------------------------ # ATxmega128A1 #------------------------------------------------------------ part parent "x128c3" desc = "ATxmega128A1"; id = "x128a1"; prog_modes = PM_SPM | PM_PDI | PM_XMEGAJTAG; mcuid = 254; n_interrupts = 125; signature = 0x1e 0x97 0x4c; memory "fuse0" size = 1; offset = 0x8f0020; ; ; #------------------------------------------------------------ # ATxmega128A1 revision D #------------------------------------------------------------ part parent "x128a1" desc = "ATxmega128A1revD"; id = "x128a1d"; mcuid = 255; signature = 0x1e 0x97 0x41; ; #------------------------------------------------------------ # ATxmega128A1U #------------------------------------------------------------ part parent "x128a1" desc = "ATxmega128A1U"; id = "x128a1u"; mcuid = 256; n_interrupts = 127; usbpid = 0x2fed; ; #------------------------------------------------------------ # ATxmega128A3 #------------------------------------------------------------ part parent "x128a1" desc = "ATxmega128A3"; id = "x128a3"; mcuid = 258; n_interrupts = 122; signature = 0x1e 0x97 0x42; ; #------------------------------------------------------------ # ATxmega128A3U #------------------------------------------------------------ part parent "x128a1" desc = "ATxmega128A3U"; id = "x128a3u"; mcuid = 259; n_interrupts = 127; signature = 0x1e 0x97 0x42; usbpid = 0x2fe6; ; #------------------------------------------------------------ # ATxmega128A4 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega128A4"; id = "x128a4"; prog_modes = PM_SPM | PM_PDI | PM_XMEGAJTAG; mcuid = 263; signature = 0x1e 0x97 0x46; memory "eeprom" size = 2048; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x22000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "application" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "apptable" size = 4096; page_size = 512; offset = 0x81f000; readsize = 256; ; memory "boot" size = 8192; page_size = 512; offset = 0x820000; readsize = 256; ; memory "fuse0" size = 1; offset = 0x8f0020; ; memory "usersig" size = 512; page_size = 512; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega128A4U #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega128A4U"; id = "x128a4u"; mcuid = 264; n_interrupts = 127; signature = 0x1e 0x97 0x46; usbpid = 0x2fde; memory "eeprom" size = 2048; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x22000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "application" size = 0x20000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "apptable" size = 4096; page_size = 256; offset = 0x81f000; readsize = 256; ; memory "boot" size = 8192; page_size = 256; offset = 0x820000; readsize = 256; ; memory "usersig" size = 256; page_size = 256; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega128B1 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega128B1"; id = "x128b1"; prog_modes = PM_SPM | PM_PDI | PM_XMEGAJTAG; mcuid = 257; n_interrupts = 81; signature = 0x1e 0x97 0x4d; usbpid = 0x2fea; memory "eeprom" size = 2048; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x22000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "application" size = 0x20000; page_size = 256; offset = 0x800000; readsize = 256; ; memory "apptable" size = 8192; page_size = 256; offset = 0x81e000; readsize = 256; ; memory "boot" size = 8192; page_size = 256; offset = 0x820000; readsize = 256; ; memory "fuse0" size = 1; offset = 0x8f0020; ; memory "usersig" size = 256; page_size = 256; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega128B3 #------------------------------------------------------------ part parent "x128b1" desc = "ATxmega128B3"; id = "x128b3"; mcuid = 260; n_interrupts = 54; signature = 0x1e 0x97 0x4b; usbpid = 0x2fe0; ; #------------------------------------------------------------ # ATxmega192C3 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega192C3"; id = "x192c3"; mcuid = 269; n_interrupts = 127; signature = 0x1e 0x97 0x51; # usbpid = 0x2f??; memory "eeprom" size = 2048; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x32000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "application" size = 0x30000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "apptable" size = 8192; page_size = 512; offset = 0x82e000; readsize = 256; ; memory "boot" size = 8192; page_size = 512; offset = 0x830000; readsize = 256; ; memory "usersig" size = 512; page_size = 512; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega192D3 #------------------------------------------------------------ part parent "x192c3" desc = "ATxmega192D3"; id = "x192d3"; mcuid = 270; n_interrupts = 114; signature = 0x1e 0x97 0x49; ; #------------------------------------------------------------ # ATxmega192A1 #------------------------------------------------------------ part parent "x192c3" desc = "ATxmega192A1"; id = "x192a1"; prog_modes = PM_SPM | PM_PDI | PM_XMEGAJTAG; mcuid = 266; signature = 0x1e 0x97 0x4e; memory "fuse0" size = 1; offset = 0x8f0020; ; ; #------------------------------------------------------------ # ATxmega192A3 #------------------------------------------------------------ part parent "x192a1" desc = "ATxmega192A3"; id = "x192a3"; mcuid = 267; n_interrupts = 122; signature = 0x1e 0x97 0x44; ; #------------------------------------------------------------ # ATxmega192A3U #------------------------------------------------------------ part parent "x192a1" desc = "ATxmega192A3U"; id = "x192a3u"; mcuid = 268; signature = 0x1e 0x97 0x44; usbpid = 0x2fe7; ; #------------------------------------------------------------ # ATxmega256C3 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega256C3"; id = "x256c3"; mcuid = 276; n_interrupts = 127; signature = 0x1e 0x98 0x46; usbpid = 0x2fda; memory "eeprom" size = 4096; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x42000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "application" size = 0x40000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "apptable" size = 8192; page_size = 512; offset = 0x83e000; readsize = 256; ; memory "boot" size = 8192; page_size = 512; offset = 0x840000; readsize = 256; ; memory "usersig" size = 512; page_size = 512; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega256D3 #------------------------------------------------------------ part parent "x256c3" desc = "ATxmega256D3"; id = "x256d3"; mcuid = 277; n_interrupts = 114; signature = 0x1e 0x98 0x44; ; #------------------------------------------------------------ # ATxmega256A1 #------------------------------------------------------------ part parent "x256c3" desc = "ATxmega256A1"; id = "x256a1"; prog_modes = PM_SPM | PM_PDI | PM_XMEGAJTAG; mcuid = 271; memory "fuse0" size = 1; offset = 0x8f0020; ; ; #------------------------------------------------------------ # ATxmega256A3 #------------------------------------------------------------ part parent "x256a1" desc = "ATxmega256A3"; id = "x256a3"; mcuid = 272; n_interrupts = 122; signature = 0x1e 0x98 0x42; ; #------------------------------------------------------------ # ATxmega256A3U #------------------------------------------------------------ part parent "x256a1" desc = "ATxmega256A3U"; id = "x256a3u"; mcuid = 275; signature = 0x1e 0x98 0x42; usbpid = 0x2fec; ; #------------------------------------------------------------ # ATxmega256A3B #------------------------------------------------------------ part parent "x256a1" desc = "ATxmega256A3B"; id = "x256a3b"; mcuid = 273; n_interrupts = 122; signature = 0x1e 0x98 0x43; ; #------------------------------------------------------------ # ATxmega256A3BU #------------------------------------------------------------ part parent "x256a1" desc = "ATxmega256A3BU"; id = "x256a3bu"; mcuid = 274; signature = 0x1e 0x98 0x43; usbpid = 0x2fe2; ; #------------------------------------------------------------ # ATxmega384C3 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega384C3"; id = "x384c3"; mcuid = 278; n_interrupts = 127; signature = 0x1e 0x98 0x45; usbpid = 0x2fdb; memory "eeprom" size = 4096; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x62000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "application" size = 0x60000; page_size = 512; offset = 0x800000; readsize = 256; ; memory "apptable" size = 8192; page_size = 512; offset = 0x85e000; readsize = 256; ; memory "boot" size = 8192; page_size = 512; offset = 0x860000; readsize = 256; ; memory "usersig" size = 512; page_size = 512; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega384D3 #------------------------------------------------------------ part parent "x384c3" desc = "ATxmega384D3"; id = "x384d3"; mcuid = 279; n_interrupts = 114; signature = 0x1e 0x98 0x47; ; #------------------------------------------------------------ # ATxmega8E5 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega8E5"; id = "x8e5"; mcuid = 230; n_interrupts = 43; signature = 0x1e 0x93 0x41; memory "eeprom" size = 512; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x2800; page_size = 128; offset = 0x800000; readsize = 256; ; memory "application" size = 8192; page_size = 128; offset = 0x800000; readsize = 256; ; memory "apptable" size = 2048; page_size = 128; offset = 0x801800; readsize = 256; ; memory "boot" size = 2048; page_size = 128; offset = 0x802000; readsize = 256; ; memory "usersig" size = 128; page_size = 128; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega16E5 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega16E5"; id = "x16e5"; mcuid = 235; n_interrupts = 43; signature = 0x1e 0x94 0x45; memory "eeprom" size = 512; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x5000; page_size = 128; offset = 0x800000; readsize = 256; ; memory "application" size = 0x4000; page_size = 128; offset = 0x800000; readsize = 256; ; memory "apptable" size = 4096; page_size = 128; offset = 0x803000; readsize = 256; ; memory "boot" size = 4096; page_size = 128; offset = 0x804000; readsize = 256; ; memory "usersig" size = 128; page_size = 128; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # ATxmega32E5 #------------------------------------------------------------ part parent ".xmega" desc = "ATxmega32E5"; id = "x32e5"; mcuid = 242; n_interrupts = 43; signature = 0x1e 0x95 0x4c; memory "eeprom" size = 1024; page_size = 32; offset = 0x8c0000; readsize = 256; ; memory "flash" size = 0x9000; page_size = 128; offset = 0x800000; readsize = 256; ; memory "application" size = 0x8000; page_size = 128; offset = 0x800000; readsize = 256; ; memory "apptable" size = 4096; page_size = 128; offset = 0x807000; readsize = 256; ; memory "boot" size = 4096; page_size = 128; offset = 0x808000; readsize = 256; ; memory "usersig" size = 128; page_size = 128; offset = 0x8e0400; readsize = 256; ; ; #------------------------------------------------------------ # AVR32UC3A0512 #------------------------------------------------------------ part desc = "AT32UC3A0512"; id = "uc3a0512"; prog_modes = PM_AVR32JTAG | PM_aWire; signature = 0xed 0xc0 0x3f; memory "flash" paged = yes; size = 0x80000; # could be set dynamicly page_size = 512; # bytes num_pages = 1024; # could be set dynamicly offset = 0x80000000; readsize = 512; # bytes ; ; #------------------------------------------------------------ # deprecated, use 'uc3a0512' #------------------------------------------------------------ part parent "uc3a0512" desc = "deprecated, use 'uc3a0512'"; id = "ucr2"; ; #------------------------------------------------------------ # ATtiny1634 #------------------------------------------------------------ part desc = "ATtiny1634"; id = "t1634"; prog_modes = PM_SPM | PM_ISP | PM_HVPP | PM_debugWIRE; mcuid = 40; n_interrupts = 28; n_page_erase = 4; stk500_devcode = 0x86; chip_erase_delay = 9000; pagel = 0xb3; bs2 = 0xb1; # avr910_devcode = 0x??; signature = 0x1e 0x94 0x12; reset = io; timeout = 200; stabdelay = 100; cmdexedelay = 25; synchloops = 32; pollindex = 3; pollvalue = 0x53; predelay = 1; postdelay = 1; pollmethod = 1; pp_controlstack = 0x0e, 0x1e, 0x0e, 0x1e, 0x2e, 0x3e, 0x2e, 0x3e, 0x4e, 0x5e, 0x4e, 0x5e, 0x6e, 0x7e, 0x6e, 0x7e, 0x26, 0x36, 0x66, 0x76, 0x2a, 0x3a, 0x6a, 0x7a, 0x2e, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; flash_instr = 0xb6, 0x01, 0x11; eeprom_instr = 0xbd, 0xf2, 0xbd, 0xe1, 0xbb, 0xcf, 0xb4, 0x00, 0xbe, 0x01, 0xb6, 0x01, 0xbc, 0x00, 0xbb, 0xbf, 0x99, 0xf9, 0xbb, 0xaf; hventerstabdelay = 100; togglevtg = 1; poweroffdelay = 15; resetdelayms = 1; hvleavestabdelay = 15; resetdelay = 15; chiperasepolltimeout = 10; programfusepolltimeout = 5; programlockpolltimeout = 5; chip_erase = "1010.1100--100x.xxxx--xxxx.xxxx--xxxx.xxxx"; pgm_enable = "1010.1100--0101.0011--xxxx.xxxx--xxxx.xxxx"; memory "eeprom" size = 256; page_size = 4; min_write_delay = 3600; max_write_delay = 3600; readback = 0xff 0xff; mode = 65; delay = 5; blocksize = 4; readsize = 256; read = "1010.0000--000x.xxxa--aaaa.aaaa--oooo.oooo"; write = "1100.0000--000x.xxxa--aaaa.aaaa--iiii.iiii"; loadpage_lo = "1100.0001--0000.0000--0000.00aa--iiii.iiii"; writepage = "1100.0010--00xx.xxxa--aaaa.aa00--xxxx.xxxx"; ; memory "flash" paged = yes; size = 0x4000; page_size = 32; num_pages = 512; min_write_delay = 4500; max_write_delay = 4500; readback = 0xff 0xff; mode = 65; delay = 6; blocksize = 128; readsize = 256; read_lo = "0010.0000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; read_hi = "0010.1000--00aa.aaaa--aaaa.aaaa--oooo.oooo"; loadpage_lo = "0100.0000--000x.xxxx--xxxx.aaaa--iiii.iiii"; loadpage_hi = "0100.1000--000x.xxxx--xxxx.aaaa--iiii.iiii"; writepage = "0100.1100--00aa.aaaa--aaaa.xxxx--xxxx.xxxx"; ; memory "lfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0000--xxxx.xxxx--iiii.iiii"; ; memory "hfuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.1000--xxxx.xxxx--iiii.iiii"; ; memory "efuse" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.0000--0000.1000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--1010.0100--xxxx.xxxx--xxxi.iiii"; ; memory "lock" size = 1; min_write_delay = 4500; max_write_delay = 4500; read = "0101.1000--0000.0000--xxxx.xxxx--oooo.oooo"; write = "1010.1100--111x.xxxx--xxxx.xxxx--1111.11ii"; ; memory "signature" size = 3; read = "0011.0000--000x.xxxx--xxxx.xxaa--oooo.oooo"; ; memory "calibration" size = 1; read = "0011.1000--000x.xxxx--0000.0000--oooo.oooo"; ; ; #------------------------------------------------------------ # ATtiny1634R #------------------------------------------------------------ part parent "t1634" desc = "ATtiny1634R"; id = "t1634r"; mcuid = 41; ; #------------------------------------------------------------ # Common values for reduced core tinys (4/5/9/10/20/40) #------------------------------------------------------------ part desc = "Common values for reduced core tinys"; id = ".reduced_core_tiny"; prog_modes = PM_TPI; memory "fuse" size = 1; page_size = 16; offset = 0x3f40; blocksize = 4; ; memory "lockbits" size = 1; page_size = 16; offset = 0x3f00; ; memory "lockbits" size = 1; page_size = 16; offset = 0x3f00; ; memory "signature" size = 3; page_size = 16; offset = 0x3fc0; ; memory "calibration" size = 1; page_size = 16; offset = 0x3f80; ; ; #------------------------------------------------------------ # ATtiny4 #------------------------------------------------------------ part parent ".reduced_core_tiny" desc = "ATtiny4"; id = "t4"; mcuid = 0; n_interrupts = 10; signature = 0x1e 0x8f 0x0a; memory "flash" size = 512; page_size = 16; offset = 0x4000; blocksize = 128; ; ; #------------------------------------------------------------ # ATtiny5 #------------------------------------------------------------ part parent "t4" desc = "ATtiny5"; id = "t5"; mcuid = 1; n_interrupts = 11; signature = 0x1e 0x8f 0x09; ; #------------------------------------------------------------ # ATtiny9 #------------------------------------------------------------ part parent ".reduced_core_tiny" desc = "ATtiny9"; id = "t9"; mcuid = 2; n_interrupts = 10; signature = 0x1e 0x90 0x08; memory "flash" size = 1024; page_size = 16; offset = 0x4000; blocksize = 128; ; ; #------------------------------------------------------------ # ATtiny10 #------------------------------------------------------------ part parent "t9" desc = "ATtiny10"; id = "t10"; mcuid = 3; n_interrupts = 11; signature = 0x1e 0x90 0x03; ; #------------------------------------------------------------ # ATtiny20 #------------------------------------------------------------ part parent ".reduced_core_tiny" desc = "ATtiny20"; id = "t20"; mcuid = 4; n_interrupts = 17; signature = 0x1e 0x91 0x0f; memory "flash" size = 2048; page_size = 16; offset = 0x4000; blocksize = 128; ; ; #------------------------------------------------------------ # ATtiny40 #------------------------------------------------------------ part parent ".reduced_core_tiny" desc = "ATtiny40"; id = "t40"; mcuid = 5; n_interrupts = 18; signature = 0x1e 0x92 0x0e; memory "flash" size = 4096; page_size = 64; offset = 0x4000; blocksize = 128; ; ; #------------------------------------------------------------ # ATtiny102 #------------------------------------------------------------ part parent ".reduced_core_tiny" desc = "ATtiny102"; id = "t102"; mcuid = 6; signature = 0x1e 0x90 0x0c; memory "flash" size = 1024; page_size = 16; offset = 0x4000; blocksize = 128; ; ; #------------------------------------------------------------ # ATtiny104 #------------------------------------------------------------ part parent ".reduced_core_tiny" desc = "ATtiny104"; id = "t104"; mcuid = 7; signature = 0x1e 0x90 0x0b; memory "flash" size = 1024; page_size = 16; offset = 0x4000; blocksize = 128; ; ; #------------------------------------------------------------ # ATmega406 #------------------------------------------------------------ part desc = "ATmega406"; id = "m406"; prog_modes = PM_SPM | PM_HVPP | PM_JTAG; mcuid = 125; n_interrupts = 23; # STK500 parameters (parallel programming IO lines) pagel = 0xa7; bs2 = 0xa0; signature = 0x1e 0x95 0x07; reset = io; serial = no; # STK500v2 HV programming parameters, from XML pp_controlstack = 0x0e, 0x1e, 0x0f, 0x1f, 0x2e, 0x3e, 0x2f, 0x3f, 0x4e, 0x5e, 0x4f, 0x5f, 0x6e, 0x7e, 0x6f, 0x7f, 0x66, 0x76, 0x67, 0x77, 0x6a, 0x7a, 0x6b, 0x7b, 0xbe, 0xfd, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00; idr = 0x51; spmcr = 0x57; eecr = 0x3f; memory "eeprom" size = 512; page_size = 4; num_pages = 128; blocksize = 4; readsize = 4; ; memory "flash" paged = yes; size = 0xa000; page_size = 128; num_pages = 320; blocksize = 128; readsize = 128; ; memory "lfuse" size = 1; ; memory "hfuse" size = 1; ; memory "lockbits" size = 1; ; memory "lockbits" size = 1; ; memory "signature" size = 3; ; ; #------------------------------------------------------------ # AVR8X family common values #------------------------------------------------------------ part desc = "AVR8X family common values"; id = ".avr8x"; prog_modes = PM_SPM | PM_UPDI; nvm_base = 0x1000; ocd_base = 0x0f80; memory "fuse0" size = 1; offset = 0x1280; readsize = 1; ; memory "wdtcfg" alias "fuse0"; ; memory "fuse1" size = 1; offset = 0x1281; readsize = 1; ; memory "bodcfg" alias "fuse1"; ; memory "fuse2" size = 1; offset = 0x1282; readsize = 1; ; memory "osccfg" alias "fuse2"; ; memory "fuse4" size = 1; offset = 0x1284; readsize = 1; ; memory "tcd0cfg" alias "fuse4"; ; memory "fuse5" size = 1; offset = 0x1285; readsize = 1; ; memory "syscfg0" alias "fuse5"; ; memory "fuse6" size = 1; offset = 0x1286; readsize = 1; ; memory "syscfg1" alias "fuse6"; ; memory "fuse7" size = 1; offset = 0x1287; readsize = 1; ; memory "append" alias "fuse7"; ; memory "codesize" alias "fuse7"; ; memory "fuse8" size = 1; offset = 0x1288; readsize = 1; ; memory "bootend" alias "fuse8"; ; memory "bootsize" alias "fuse8"; ; memory "fuses" size = 9; page_size = 10; offset = 0x1280; readsize = 10; ; memory "lock" size = 1; offset = 0x128a; readsize = 1; ; memory "tempsense" size = 2; offset = 0x1120; readsize = 1; ; memory "signature" size = 3; offset = 0x1100; readsize = 3; ; memory "prodsig" size = 61; page_size = 61; offset = 0x1103; readsize = 61; ; memory "sernum" size = 10; offset = 0x1104; readsize = 1; ; memory "osccal16" size = 2; offset = 0x1118; readsize = 1; ; memory "osccal20" size = 2; offset = 0x111a; readsize = 1; ; memory "osc16err" size = 2; offset = 0x1122; readsize = 1; ; memory "osc20err" size = 2; offset = 0x1124; readsize = 1; ; memory "data" # SRAM, only used to supply the offset offset = 0x1000000; ; ; #------------------------------------------------------------ # AVR8X tiny family common values #------------------------------------------------------------ part parent ".avr8x" desc = "AVR8X tiny family common values"; id = ".avr8x_tiny"; family_id = "tinyAVR"; # Shared UPDI pin, HV on UPDI pin hvupdi_variant = 0; memory "userrow" size = 32; page_size = 32; offset = 0x1300; readsize = 256; ; memory "usersig" alias "userrow"; ; ; #------------------------------------------------------------ # AVR8X mega family common values #------------------------------------------------------------ part parent ".avr8x" desc = "AVR8X mega family common values"; id = ".avr8x_mega"; family_id = "megaAVR"; # Dedicated UPDI pin, no HV hvupdi_variant = 1; memory "userrow" size = 64; page_size = 64; offset = 0x1300; readsize = 256; ; memory "usersig" alias "userrow"; ; ; #------------------------------------------------------------ # ATtiny202 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny202"; id = "t202"; mcuid = 280; n_interrupts = 26; signature = 0x1e 0x91 0x23; memory "eeprom" size = 64; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 2048; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny204 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny204"; id = "t204"; mcuid = 281; n_interrupts = 26; signature = 0x1e 0x91 0x22; memory "eeprom" size = 64; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 2048; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny402 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny402"; id = "t402"; mcuid = 284; n_interrupts = 26; signature = 0x1e 0x92 0x27; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny404 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny404"; id = "t404"; mcuid = 285; n_interrupts = 26; signature = 0x1e 0x92 0x26; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny406 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny406"; id = "t406"; mcuid = 286; n_interrupts = 26; signature = 0x1e 0x92 0x25; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny804 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny804"; id = "t804"; mcuid = 295; n_interrupts = 31; signature = 0x1e 0x93 0x25; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny806 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny806"; id = "t806"; mcuid = 296; n_interrupts = 31; signature = 0x1e 0x93 0x24; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny807 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny807"; id = "t807"; mcuid = 297; n_interrupts = 31; signature = 0x1e 0x93 0x23; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1604 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1604"; id = "t1604"; mcuid = 304; n_interrupts = 31; signature = 0x1e 0x94 0x25; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1606 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1606"; id = "t1606"; mcuid = 305; n_interrupts = 31; signature = 0x1e 0x94 0x24; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1607 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1607"; id = "t1607"; mcuid = 306; n_interrupts = 31; signature = 0x1e 0x94 0x23; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny212 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny212"; id = "t212"; mcuid = 282; n_interrupts = 26; signature = 0x1e 0x91 0x21; memory "eeprom" size = 64; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 2048; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny214 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny214"; id = "t214"; mcuid = 283; n_interrupts = 26; signature = 0x1e 0x91 0x20; memory "eeprom" size = 64; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 2048; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny412 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny412"; id = "t412"; mcuid = 287; n_interrupts = 26; signature = 0x1e 0x92 0x23; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny414 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny414"; id = "t414"; mcuid = 288; n_interrupts = 26; signature = 0x1e 0x92 0x22; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny416 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny416"; id = "t416"; mcuid = 289; n_interrupts = 26; signature = 0x1e 0x92 0x21; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny417 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny417"; id = "t417"; mcuid = 291; n_interrupts = 26; signature = 0x1e 0x92 0x20; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny814 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny814"; id = "t814"; mcuid = 298; n_interrupts = 26; signature = 0x1e 0x93 0x22; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny816 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny816"; id = "t816"; mcuid = 299; n_interrupts = 26; signature = 0x1e 0x93 0x21; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny817 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny817"; id = "t817"; mcuid = 300; n_interrupts = 26; signature = 0x1e 0x93 0x20; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1614 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1614"; id = "t1614"; mcuid = 307; n_interrupts = 31; signature = 0x1e 0x94 0x22; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1616 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1616"; id = "t1616"; mcuid = 308; n_interrupts = 31; signature = 0x1e 0x94 0x21; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1617 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1617"; id = "t1617"; mcuid = 309; n_interrupts = 31; signature = 0x1e 0x94 0x20; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny3216 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny3216"; id = "t3216"; mcuid = 314; n_interrupts = 31; signature = 0x1e 0x95 0x21; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 128; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny3217 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny3217"; id = "t3217"; mcuid = 315; n_interrupts = 31; signature = 0x1e 0x95 0x22; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 128; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny424 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny424"; id = "t424"; mcuid = 292; signature = 0x1e 0x92 0x2c; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny426 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny426"; id = "t426"; mcuid = 293; signature = 0x1e 0x92 0x2b; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny427 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny427"; id = "t427"; mcuid = 294; signature = 0x1e 0x92 0x2a; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 4096; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny824 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny824"; id = "t824"; mcuid = 301; signature = 0x1e 0x93 0x29; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny826 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny826"; id = "t826"; mcuid = 302; signature = 0x1e 0x93 0x28; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny827 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny827"; id = "t827"; mcuid = 303; signature = 0x1e 0x93 0x27; memory "eeprom" size = 128; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1624 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1624"; id = "t1624"; mcuid = 310; signature = 0x1e 0x94 0x2a; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1626 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1626"; id = "t1626"; mcuid = 311; signature = 0x1e 0x94 0x29; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny1627 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny1627"; id = "t1627"; mcuid = 312; signature = 0x1e 0x94 0x28; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny3224 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny3224"; id = "t3224"; mcuid = 316; signature = 0x1e 0x95 0x28; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 128; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny3226 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny3226"; id = "t3226"; mcuid = 317; signature = 0x1e 0x95 0x27; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 128; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATtiny3227 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATtiny3227"; id = "t3227"; mcuid = 318; signature = 0x1e 0x95 0x26; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 128; offset = 0x8000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega808 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATmega808"; id = "m808"; mcuid = 319; n_interrupts = 36; signature = 0x1e 0x93 0x26; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega809 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATmega809"; id = "m809"; mcuid = 320; n_interrupts = 40; signature = 0x1e 0x93 0x2a; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega1608 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATmega1608"; id = "m1608"; mcuid = 321; n_interrupts = 36; signature = 0x1e 0x94 0x27; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega1609 #------------------------------------------------------------ part parent ".avr8x_tiny" desc = "ATmega1609"; id = "m1609"; mcuid = 322; n_interrupts = 40; signature = 0x1e 0x94 0x26; memory "eeprom" size = 256; page_size = 32; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega3208 #------------------------------------------------------------ part parent ".avr8x_mega" desc = "ATmega3208"; id = "m3208"; mcuid = 323; n_interrupts = 36; signature = 0x1e 0x95 0x30; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 128; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega3209 #------------------------------------------------------------ part parent ".avr8x_mega" desc = "ATmega3209"; id = "m3209"; mcuid = 324; n_interrupts = 40; signature = 0x1e 0x95 0x31; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 128; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega4808 #------------------------------------------------------------ part parent ".avr8x_mega" desc = "ATmega4808"; id = "m4808"; mcuid = 325; n_interrupts = 36; signature = 0x1e 0x96 0x50; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0xc000; page_size = 128; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # ATmega4809 #------------------------------------------------------------ part parent ".avr8x_mega" desc = "ATmega4809"; id = "m4809"; mcuid = 326; n_interrupts = 40; signature = 0x1e 0x96 0x51; memory "eeprom" size = 256; page_size = 64; offset = 0x1400; readsize = 256; ; memory "flash" size = 0xc000; page_size = 128; offset = 0x4000; readsize = 256; ; ; #------------------------------------------------------------ # AVR-Dx family common values #------------------------------------------------------------ part desc = "AVR-Dx family common values"; id = ".avrdx"; prog_modes = PM_SPM | PM_UPDI; # Dedicated UPDI pin, no HV hvupdi_variant = 1; nvm_base = 0x1000; ocd_base = 0x0f80; memory "fuse0" size = 1; offset = 0x1050; readsize = 1; ; memory "wdtcfg" alias "fuse0"; ; memory "fuse1" size = 1; offset = 0x1051; readsize = 1; ; memory "bodcfg" alias "fuse1"; ; memory "fuse2" size = 1; offset = 0x1052; readsize = 1; ; memory "osccfg" alias "fuse2"; ; memory "fuse4" size = 1; offset = 0x1054; readsize = 1; ; memory "tcd0cfg" alias "fuse4"; ; memory "fuse5" size = 1; offset = 0x1055; readsize = 1; ; memory "syscfg0" alias "fuse5"; ; memory "fuse6" size = 1; offset = 0x1056; readsize = 1; ; memory "syscfg1" alias "fuse6"; ; memory "fuse7" size = 1; offset = 0x1057; readsize = 1; ; memory "codesize" alias "fuse7"; ; memory "append" alias "fuse7"; ; memory "fuse8" size = 1; offset = 0x1058; readsize = 1; ; memory "bootsize" alias "fuse8"; ; memory "bootend" alias "fuse8"; ; memory "fuses" size = 9; page_size = 16; offset = 0x1050; readsize = 16; ; memory "lock" size = 4; offset = 0x1040; readsize = 4; ; memory "tempsense" size = 2; offset = 0x1104; readsize = 1; ; memory "signature" size = 3; offset = 0x1100; readsize = 3; ; memory "prodsig" size = 125; page_size = 125; offset = 0x1103; readsize = 125; ; memory "sernum" size = 16; offset = 0x1110; readsize = 1; ; memory "userrow" size = 32; page_size = 32; offset = 0x1080; readsize = 32; ; memory "usersig" alias "userrow"; ; memory "data" # SRAM, only used to supply the offset offset = 0x1000000; ; ; #------------------------------------------------------------ # AVR32DA28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DA28"; id = "avr32da28"; mcuid = 338; signature = 0x1e 0x95 0x34; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DA32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DA32"; id = "avr32da32"; mcuid = 342; signature = 0x1e 0x95 0x33; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DA48 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DA48"; id = "avr32da48"; mcuid = 346; signature = 0x1e 0x95 0x32; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DA28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DA28"; id = "avr64da28"; mcuid = 351; signature = 0x1e 0x96 0x15; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DA32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DA32"; id = "avr64da32"; mcuid = 355; signature = 0x1e 0x96 0x14; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DA48 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DA48"; id = "avr64da48"; mcuid = 359; signature = 0x1e 0x96 0x13; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DA64 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DA64"; id = "avr64da64"; mcuid = 362; signature = 0x1e 0x96 0x12; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DA28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DA28"; id = "avr128da28"; mcuid = 364; signature = 0x1e 0x97 0x0a; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DA32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DA32"; id = "avr128da32"; mcuid = 366; signature = 0x1e 0x97 0x09; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DA48 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DA48"; id = "avr128da48"; mcuid = 368; signature = 0x1e 0x97 0x08; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DA64 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DA64"; id = "avr128da64"; mcuid = 370; signature = 0x1e 0x97 0x07; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DB28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DB28"; id = "avr32db28"; mcuid = 339; signature = 0x1e 0x95 0x37; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DB32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DB32"; id = "avr32db32"; mcuid = 343; signature = 0x1e 0x95 0x36; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DB48 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DB48"; id = "avr32db48"; mcuid = 347; signature = 0x1e 0x95 0x35; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DB28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DB28"; id = "avr64db28"; mcuid = 352; signature = 0x1e 0x96 0x19; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DB32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DB32"; id = "avr64db32"; mcuid = 356; signature = 0x1e 0x96 0x18; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DB48 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DB48"; id = "avr64db48"; mcuid = 360; signature = 0x1e 0x96 0x17; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DB64 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DB64"; id = "avr64db64"; mcuid = 363; signature = 0x1e 0x96 0x16; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DB28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DB28"; id = "avr128db28"; mcuid = 365; signature = 0x1e 0x97 0x0e; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DB32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DB32"; id = "avr128db32"; mcuid = 367; signature = 0x1e 0x97 0x0d; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DB48 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DB48"; id = "avr128db48"; mcuid = 369; signature = 0x1e 0x97 0x0c; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR128DB64 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR128DB64"; id = "avr128db64"; mcuid = 371; signature = 0x1e 0x97 0x0b; memory "eeprom" size = 512; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x20000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR16DD14 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR16DD14"; id = "avr16dd14"; mcuid = 329; hvupdi_variant = 2; signature = 0x1e 0x94 0x34; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR16DD20 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR16DD20"; id = "avr16dd20"; mcuid = 330; hvupdi_variant = 2; signature = 0x1e 0x94 0x33; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR16DD28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR16DD28"; id = "avr16dd28"; mcuid = 331; hvupdi_variant = 2; signature = 0x1e 0x94 0x32; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR16DD32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR16DD32"; id = "avr16dd32"; mcuid = 333; hvupdi_variant = 2; signature = 0x1e 0x94 0x31; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DD14 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DD14"; id = "avr32dd14"; mcuid = 336; hvupdi_variant = 2; signature = 0x1e 0x95 0x3b; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DD20 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DD20"; id = "avr32dd20"; mcuid = 337; hvupdi_variant = 2; signature = 0x1e 0x95 0x3a; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DD28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DD28"; id = "avr32dd28"; mcuid = 340; hvupdi_variant = 2; signature = 0x1e 0x95 0x39; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32DD32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR32DD32"; id = "avr32dd32"; mcuid = 344; hvupdi_variant = 2; signature = 0x1e 0x95 0x38; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DD14 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DD14"; id = "avr64dd14"; mcuid = 349; hvupdi_variant = 2; signature = 0x1e 0x96 0x1d; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DD20 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DD20"; id = "avr64dd20"; mcuid = 350; hvupdi_variant = 2; signature = 0x1e 0x96 0x1c; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DD28 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DD28"; id = "avr64dd28"; mcuid = 353; hvupdi_variant = 2; signature = 0x1e 0x96 0x1b; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64DD32 #------------------------------------------------------------ part parent ".avrdx" desc = "AVR64DD32"; id = "avr64dd32"; mcuid = 357; hvupdi_variant = 2; signature = 0x1e 0x96 0x1a; memory "eeprom" size = 256; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 512; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR-Ex family common values #------------------------------------------------------------ part parent ".avrdx" desc = "AVR-Ex family common values"; id = ".avrex"; # Shared UPDI pin, HV on _RESET hvupdi_variant = 2; memory "userrow" size = 64; page_size = 64; readsize = 64; ; memory "usersig" alias "userrow"; ; ; #------------------------------------------------------------ # AVR8EA28 #------------------------------------------------------------ part parent ".avrex" desc = "AVR8EA28"; id = "avr8ea28"; mcuid = 327; signature = 0x1e 0x93 0x2c; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR8EA32 #------------------------------------------------------------ part parent ".avrex" desc = "AVR8EA32"; id = "avr8ea32"; mcuid = 328; signature = 0x1e 0x93 0x2b; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 8192; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR16EA28 #------------------------------------------------------------ part parent ".avrex" desc = "AVR16EA28"; id = "avr16ea28"; mcuid = 332; signature = 0x1e 0x94 0x37; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR16EA32 #------------------------------------------------------------ part parent ".avrex" desc = "AVR16EA32"; id = "avr16ea32"; mcuid = 334; signature = 0x1e 0x94 0x36; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR16EA48 #------------------------------------------------------------ part parent ".avrex" desc = "AVR16EA48"; id = "avr16ea48"; mcuid = 335; signature = 0x1e 0x94 0x35; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x4000; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32EA28 #------------------------------------------------------------ part parent ".avrex" desc = "AVR32EA28"; id = "avr32ea28"; mcuid = 341; signature = 0x1e 0x95 0x3e; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32EA32 #------------------------------------------------------------ part parent ".avrex" desc = "AVR32EA32"; id = "avr32ea32"; mcuid = 345; signature = 0x1e 0x95 0x3d; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR32EA48 #------------------------------------------------------------ part parent ".avrex" desc = "AVR32EA48"; id = "avr32ea48"; mcuid = 348; signature = 0x1e 0x95 0x3c; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x8000; page_size = 64; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64EA28 #------------------------------------------------------------ part parent ".avrex" desc = "AVR64EA28"; id = "avr64ea28"; mcuid = 354; signature = 0x1e 0x96 0x20; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 128; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64EA32 #------------------------------------------------------------ part parent ".avrex" desc = "AVR64EA32"; id = "avr64ea32"; mcuid = 358; signature = 0x1e 0x96 0x1f; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 128; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # AVR64EA48 #------------------------------------------------------------ part parent ".avrex" desc = "AVR64EA48"; id = "avr64ea48"; mcuid = 361; signature = 0x1e 0x96 0x1e; memory "eeprom" size = 512; page_size = 8; offset = 0x1400; readsize = 256; ; memory "flash" size = 0x10000; page_size = 128; offset = 0x800000; readsize = 256; ; ; #------------------------------------------------------------ # Logic Green parts #------------------------------------------------------------ part parent "m88" desc = "LGT8F88P"; id = "lgt8f88p"; mcuid = 227; signature = 0x1e 0x93 0x0f; ; #------------------------------------------------------------ # LGT8F168P #------------------------------------------------------------ part parent "m168" desc = "LGT8F168P"; id = "lgt8f168p"; mcuid = 228; signature = 0x1e 0x94 0x0b; ; #------------------------------------------------------------ # LGT8F328P #------------------------------------------------------------ part parent "m328" desc = "LGT8F328P"; id = "lgt8f328p"; mcuid = 229; signature = 0x1e 0x95 0x0f; ;