2006-12-21 Joerg Wunsch Submitted by Christian Starkjohann: patch #5507: Support for AVR-Doper USB programmer in HID mode * configure.ac: Add hooks to detect the Win32 HID library, as well as the existence of . * Makefile.am: Add new files. * my_ddk_hidsdi.h: (New file.) * ser_avrdoper.c: (New file.) * serial.h: Add declaration for avrdoper_serdev. * stk500v2.c: Add hook to divert to the AVR Doper code. * avrdude.1: Document the AVR Doper support. * doc/avrdude.texi: (Ditto.) 2006-12-15 Joerg Wunsch Submitted by ivanv at netman.ru * jtagmkI.c: fix length for single-byte write operations. Closes bug #18527 JTAG ICE: fuse bits have been writen incorrectly 2006-12-11 Joerg Wunsch * jtagmkII.c (jtagmkII_paged_write): Remove a debugging usleep(1000000) that accidentally crept in in rev 1.19. 2006-12-11 Joerg Wunsch * ser_posix.c (ser_open): Do fill in fdp->ifd before already using it in ser_setspeed(). 2006-12-11 Joerg Wunsch * jtagmkI.c (jtagmkI_close): revert baud rate to the initial value in case we had changed it. Fixes bug #18262: JTAGMKI/JTAG1 Reset Bug 2006-12-11 Colin O'Flynn * safemode.c: Stop ignoring return values! Closes bug #18339 2006-12-11 Joerg Wunsch Submitted by Nick Lott: * avrdude.conf.in: Fix signature for ATmega8515. Closes bug #18348: ATMEGA8515 Signature is wrong in avrdude.conf 2006-12-11 Joerg Wunsch * avr.c: Fix a bug introduced in rev. 1.69, when implementing the fallback from each programmer's paged_load() or paged_write() method, respectively. The return value needs to be checked for being greater or equal than 0 rather equal to 0 in order to assume the operation has been successful. Fixes bug #18489: avrdude is too slow (20 byte/s) 2006-12-11 Joerg Wunsch * avr910.c: Make the code compile warning-free: - declare a dummy "struct timezone" for some Win32 systems (MinGW) - fix a few printf() argument types - get rid off the prevailing "all filedescriptors are of type int" attitude The last item required a large sweep across the code, in order to replace all "int fd"s by "struct filedescriptor *fd"s, and pass pointers (as we cannot pass a union directly). In return, the code is now supposed to be fully 64-bit safe, rather than relying on a 64-bit pointer being converted to a (32-bit) int and back to a pointer as we did previously. * butterfly.c: (Ditto.) * jtagmkI.c: (Ditto.) * jtagmkII.c: (Ditto.) * lists.c: (Ditto.) * par.c: (Ditto.) * pgm.h: (Ditto.) * ppi.c: (Ditto.) * ppi.h: (Ditto.) * ppiwin.c: (Ditto.) * ser_posix.c: (Ditto.) * ser_win32.c: (Ditto.) * serbb_posix.c: (Ditto.) * serbb_win32.c: (Ditto.) * serial.h: (Ditto.) * stk500.c: (Ditto.) * stk500v2.c: (Ditto.) * usb_libusb.c: (Ditto.) 2006-11-23 Joerg Wunsch Implement EEPROM access through debugWire. * jtagmkII.c: Extend the jtagmkII_read_byte() and jtagmkII_write_byte() methods to handle EEPROM through debugWire. * avrpart.h: Implement the "flash instruction" parameter. * config_gram.y: (Ditto.) * lexer.l: (Ditto.) * avrdude.conf.in: (Ditto.) * avrdude.1: Document the EEPROM access through dW. * doc/avrdude.texi: (Ditto.) * tools/get-dw-params.xsl: Extend to extract the flash instruction field. 2006-11-23 Joerg Wunsch * avr.c (avr_read, avr_write): if the paged access returns a failure, fall back to byte access. 2006-11-21 Joerg Wunsch * jtagmkII.c: In jtagmkII_read_byte() and jtagmkII_write_byte(), return an error upon failure now that the upper layers won't fall back to the cmd() method anymore in that case. 2006-11-21 Joerg Wunsch Implement debugWire programming support. * avrpart.h: Implement debugWire support. * config_gram.y: (Ditto.) * jtagmkII.c: (Ditto.) * jtagmkII.h: (Ditto.) * lexer.l: (Ditto.) * avrdude.conf.in: Add the new dW programmers. * avrdude.1: Document the dW support. * doc/avrdude.texi: (Ditto.) * tools/get-dw-params.xsl: XSL stylesheet to extract the dW parameters from the XML files. 2006-11-20 Joerg Wunsch * jtagmkI.c (jtagmkI_close): remove two unused variables. 2006-11-20 Joerg Wunsch * avr.c: Replace the fallback of avr_read_byte() and avr_write_byte() to avr_read_byte_default() and avr_write_byte_default (resp.) by directly calling the latter functions from within all programmers that don't implement their own read_byte()/write_byte() methods. In turn, make the read_byte() and write_byte() methods mandatory, and the cmd() method (direct ISP command) optional instead (it's effectively mandatory for any programmer using avr_read_byte_default()/avr_write_byte_default() though). Remove all the pointless cmd() method stubs from those programmers that don't need it. Eliminate avr_read_byte() as it was now completely identical to pgm->read_byte(). * avr.h: (Ditto.) * bitbang.c: (Ditto.) * butterfly.c: (Ditto.) * jtagmkI.c: (Ditto.) * jtagmkII.c: (Ditto.) * par.c: (Ditto.) * pgm.c: (Ditto.) * safemode.c: (Ditto.) * serbb_posix.c: (Ditto.) * serbb_win32.c: (Ditto.) * stk500.c: (Ditto.) * stk500v2.c: (Ditto.) * term.c: (Ditto.) * usbasp.c: (Ditto.) 2006-11-13 Joerg Wunsch * jtagmkI.c: Avoid sending a CMD_RESET when leaving programming mode, and CMD_GO when closing the connection. They cause the activity LED on the ICE to continue to flicker, and are not necessary anyway (the target starts to run by itself when leaving programmng mode). This is a partial fix for bug #18262: JTAGMKI/JTAG1 Reset Bug 2006-11-12 Colin O'Flunn * avrdude.conf.in: Add read command for lockbits for Tiny2313. Applies patch #5538 2006-11-10 Joerg Wunsch * avrdude.conf.in: Add signatures for ATmega325/3250/645/6450. 2006-11-08 Joerg Wunsch * configure.ac: Preserve ${LDFLAGS} inherited from environment for Win32 environments. 2006-11-07 Joerg Wunsch * configure.ac: Don't pretend --enable-doc were the default. 2006-11-02 Joerg Wunsch * avrdude.conf.in: Fix the width of the efuse memory area for a number of AVRs. Closes bug #18182: Wrong setting of eFuse configuration for mega640/1280/1281/2560/2561 in avrdude 5.2 2006-11-01 Joerg Wunsch * avrdude.conf.in: Implement HVSP and PP modes for the AVR Dragon. * config_gram.y: (Ditto.) * jtagmkII.c: (Ditto.) * jtagmkII_private.h: (Ditto.) * lexer.l: (Ditto.) * stk500v2.c: (Ditto.) * stk500v2.h: (Ditto.) * avrdude.1: Document the HVSP and PP support for the Dragon. * doc/avrdude.texi: (Ditto.) 2006-10-27 Joerg Wunsch * jtagmkI.c: Implement a flags field in struct serdev, and populate it with a flag that indicates whether the underlying communication can dynamically change its speed or not. This flag is set for true serial communication but clear for USB communication. Don't try to adjust the speed when talking over a communication channel that doesn't support it. (The Dragon does not even support the respective parameter.) * jtagmkII.c: (Ditto.) * ser_posix.c: (Ditto.) * ser_win32.c: (Ditto.) * serial.h: (Ditto.) * usb_libusb.c: (Ditto.) 2006-10-26 Joerg Wunsch * avrdude.conf.in: Add support for the AVR Dragon (JTAG and ISP mode). * config_gram.y: (Ditto.) * jtagmkII.c: (Ditto.) * jtagmkII.h: (Ditto.) * lexer.l: (Ditto.) * stk500v2.c: (Ditto.) * stk500v2.h: (Ditto.) * usbdevs.h: (Ditto.) * avrdude.1: Document the AVR Dragon support. * doc/avrdude.texi: (Ditto.) 2006-10-09 Joerg Wunsch Released AVRDUDE 5.2. 2006-10-09 Joerg Wunsch * configure.ac: Bump version to 5.2 2006-10-09 Joerg Wunsch Submitted by John Voltz: add AVR053 oscillator calibration. * main.c: Add the -O option. * pgm.c: Add the hook for the perform_osccal() method. * pgm.h: (Ditto.) * stk500v2.c: Implement perform_osccal(). * avrdude.1: Document the -O option. * doc/avrdude.texi: (Ditto.) Partially closes bug #17487: AVR RC oscillator calibration routine not supported (feature request) 2006-10-09 Joerg Wunsch Submitted by freckle@sf.net: * stk500.c (stk500_paged_write): Send the command and the data payload within a single write(). patch #5025: Improve stk500.c robustness Submitted by Matthias Ringwald: * stk500.c (stk500_open): do not flush the serial line after getting in sync with the programmer. patch #5293: stk500.c: no drain after sync (-> allow BTnode Bootloader to work on cygwin) 2006-09-29 Joerg Wunsch * pgm.h: Fix prototype for gettimeofday(). Closes bug #17884: another gettimeofday conflict under win32/cygwin 2006-09-24 Joerg Wunsch Submitted by Thomas Fischl (initially): * configure.ac: Add the CoreFoundation and IOKit framework linker flags on MacOS X when configuring for USB support. patch #4685: Libusb on MacOS X: detection and additional includes 2006-09-20 Joerg Wunsch * avr910.c: As there is a lot of ambiguity about the AVR910 device codes, allow the user to override the device code verification with the -F option. * main.c: Make ovsigck a global variable. 2006-09-20 Joerg Wunsch Add the "stk500generic" programmer that auto-probes for STK500 either firmware version 1 or 2. * Makefile.am (avrdude_SOURCES): add the new files stk500generic.c and stk500generic.h. * avrdude.conf.in: Add the stk500generic programmer type, and change the "stk500" entry to point to this programmer. * config_gram.y: Add the stk500generic keyword. * lexer.l: (Ditto.) * stk500.c: Change the stk500v1 code to not call exit() prematurely when failing to open the programmer, but instead return an error status. * stk500generic.c: (New file.) Stub programmer implementation. Probe for either stk500v1 or stk500v2, and adjust the current pgm appropriately. * stk500generic.h: (New file.) Declare the public interface(s) of stk500generic.c. * doc/avrdude.texi: Document the changed behaviour of stk500. 2006-09-18 Joerg Wunsch * avrdude.conf.in: Various fixes for ancient processors and their capabilities. For the AT90S1200 and the AT90S8515, fuse bit handling via ISP, and lock bit reading via ISP are not supported at all. For the AT90S4414 (small brother of the AT90S8515), add the ability to write the lock bits, and add a definition for the fuse bits (usable for HV programming). For the AT90S2313, add the "fuse" memory range, so it's available for HV programming. Resolves bug #17796: avrdude will not program or verify lockbits with Atmel STK protocol programmers 2006-09-17 Joerg Wunsch Submitted by Thomas Fischl: * usbasp.c: Check for USBasp with new as well as old VID/PID pair, warn the user about upgrading the firmware in case an old one has been found. * usbasp.h: Add new VID/PID. 2006-09-15 Joerg Wunsch * avrdude.conf.in: Fix some mistakes for the ATtinyX61 family: . high fuse has 8 bits . there is an extended fuse (just one bit) . the calibration area is only 1 byte 2006-09-12 Joerg Wunsch * doc/avrdude.texi: Convert some of the tables to multitables in order to beautify the result. 2006-09-10 Joerg Wunsch Contributed by Thomas Fischl: add support for USBasp. patch #4686: Add support for USBasp, a simple USB programmer * usbasp.c: New file, implement the USBasp driver. * usbasp.h: New file, interface declarations for USBasp. * Makefile.am: Wire the new files into the build. * avrdude.conf.in: Add the usbasp programmer entry. * config_gram.y: Add the usbasp token. * lexer.l: (Ditto.) * avrdude.1: Document the USBasp programmer. * doc/avrdude.texi: (Ditto.) 2006-09-08 Joerg Wunsch * main.c: Implement -U filename as a shorthand for -U flash:w:filename:a. * avrdude.1: Document this. * doc/avrdude.texi: (Ditto.) 2006-09-08 Joerg Wunsch Implement numerical output formats for decimal, hexadecimal, octal, and binary numbers. Closes bug #16129: more output formats for fuse bits (avrdude enhancement request) * fileio.c: Implement fileio_num() and the itoa_simple() helper function. * fileio.h: Add new file formats to FILEFMT. * main.c: Parse the new file formats. * avrdude.1: Document all this. * doc/avrdude.texi: (Ditto.) 2006-09-08 Joerg Wunsch * fileio.c: CPP statements start in column #1. * stk500v2.c: Hide two debug/trace statements behind "verbose". 2006-09-07 Joerg Wunsch * avrdude.1: Describe how to disable the DWEN fuse. * doc/avrdude.texi: (Ditto.) 2006-09-07 Joerg Wunsch * jtagmkII.c: Translate numerical response codes to strings. 2006-09-07 Joerg Wunsch * avrdude.1: The avr109 programmer type no longer chokes on a wrong avr910 device ID, so remove that description. * doc/avrdude.texi: (Ditto.) 2006-09-07 Joerg Wunsch * jtagmkII.c: When failing to start in ISP mode, try debugWire instead. This requires the user to eventually restart AVRDUE from scratch then. 2006-09-06 Joerg Wunsch Add support for the JTAG ICE mkII in ISP mode. * avrdude.conf.in (jtag2isp): New programmer entry. * config_gram.y: Add K_JTAG_MKII_ISP. * jtagmkII.c: Restructure and export some more functions. * jtagmkII.h: Declare exported functions. * jtagmkII_private.h: Prepare file to be included in stk500v2.c. * lexer.l: Add jtagmkii_isp token. * stk500v2.c: Implement glue to jtagmkII.c. * stk500v2.h: Declare stk500v2_jtagmkII_initpgm(). * avrdude.1: Document the new programmer support. * doc/avrdude.texi: (Ditto.) 2006-09-01 Joerg Wunsch * main.c: Add date and time of compilation to the verbose greeting message. Idea taken from patch #3172: Adds date and time of compile to usage message 2006-09-01 Joerg Wunsch Contributed by as patch #4372: Better synchronization for stk500 * stk500.c: Sync three times, and drop any noise inbetween. 2006-09-01 Joerg Wunsch * avrdude.conf.in (ATtiny261, ATtiny461, ATtiny861): new entries. 2006-09-01 Joerg Wunsch * butterfly.c: Remove the device support decision based on the old AVR910 device codes; we've got signature verification now so better rely on that. * avr910.c: Revert the signature bytes returned, as it already happened in butterfly.c. This closes bug #14998: Signature Bytes read in wrong order (avr910 mode) 2006-09-01 Joerg Wunsch Submitted by Wim Lewis. * serbb_posix.c: Improve error handling. patch #4923: Better error reporting for serial-bitbang programmers 2006-08-31 Joerg Wunsch * avrdude.conf.in: Introduce a "stk500v1" entry, so we can switch the default "stk500" to "stk500v2" some day. 2006-08-31 Joerg Wunsch The major part of this change has been contributed by . Implements patch #4635: Add support for terminal/console servers for serial programmers * ser_posix.c: Add net_open(), and divert to it for net:host:port. * ser_win32.c: Recognize net:host:port, and bail out. * avrdude.1: Document the net:host:port connection option. * doc/avrdude.texi: (Ditto.) 2006-08-31 Joerg Wunsch Fix for bug #16627: Butterfly programmer does not reset after programming * butterfly.c: Wait for the device's response after sending an "E" command. 2006-08-31 Joerg Wunsch Tentative fix for bug #16156: Problem with Si-Prog * serbb_posix.c: Disable reset before closing. * serbb_win32.c: (Ditto.) 2006-08-30 Joerg Wunsch Rewrite the serbb code so the pin numbering matches the DB9 connector, and fix some related bugs in serbb_posix.c. Closes bug #16265: dasa2 does not work under posix * avrdude.conf.in: New serbb pin numbering; added "siprog" as an alias for "ponyser". * serbb_posix.c: New pin numbering, fix some confusion. * serbb_win32.c: New pin numbering. The generic and Posix-related parts of these changes have been contributed by Hanns-Konrad Unger 2006-08-30 Joerg Wunsch Contributed by the anonymous developer of patch #5096: * avrdude.conf.in (blaster): Add an entry for the Altera byteblaster. 2006-08-30 Joerg Wunsch Rework the exit specs so they actually work again. It should be possible to extend them for other programmers than PPI now (serbb, stk500*). * pgm.h: Keep the exit specs in an abstract form inside struct programmer_t. (Should be moved out into some programmer-specific structure.) Rename the getexitspecs() method into parseexitspecs(). * main.c: Move the exit specs stuff out to the programmer implementation. * par.c: Implement the new exit spec handling. Everything is now done using the generic abstraction layer. Closes bug #16443: No disable Resetsignal at the end of Programming Session Obviates need for patch #5057: quick and dirty Hack to unset Reset after Programming 2006-08-29 Joerg Wunsch This patch has been contributed by an anonymous developer via the patch tracking system. patch #5096: Allow VCC and BUFF to be any pin in parallel mode * config_gram.y: Release the restriction to PPIDATA pins. * par.c: Rework the code to introduce a function par_setmany() that builds on top of par_setpin(), and use that function for the PPI_AVR_VCC and PPI_AVR_BUFF pin collections. This also abstracts the polarity of these signals appropriately. 2006-08-28 Joerg Wunsch Contributed by Ned Konz: * ser_posix.c: Open the serial port with O_NONBLOCK, and save and restore the port state before exiting. patch #5008: Patch for (5.1) ser_posix.c for O_NONBLOCK open and restoring serial port state on close Closes bug #12622: avrdude hangs on macosx/darwin with PL-2303 usb-to-serial and Butterfly 2006-08-22 Joerg Wunsch * bitbang.c: Move the bitbang prerequisite checks out from main() into their own bitbang_check_prerequisites(). * bitbang.h: (Ditto.) * main.c: (Ditto.) * par.c: (Ditto.) * serbb_posix.c: (Ditto.) * serbb_win32.c: (Ditto.) 2006-08-22 Joerg Wunsch * avrdude.conf.in: Add page mode parameters for all "eeprom" memory definitions that are organized in pages. * avr.c (avr_write_byte_default): Consider using the loadpage instructions only if the respective memory is marked "paged". Closes bug #17199: EEPROM fails verification on ATmega645 with pony-stk200 hardware Closes bug #16849: EEPROM write fails for AT90USB1287 with mode 0x41 Closes bug #15146: stk500v2_paged_write: loadpage instruction not defined for part 2006-08-22 Joerg Wunsch * doc/avrdude.info (-c): Change "avrispmk2" into "avrisp2" as that is the programmer actually supported by avrdude.conf.in. Closes bug #15677: documentation mentions wrong programmer-id "avrispmk2" 2006-08-21 Joerg Wunsch * avrdude.conf.in: Fix various AVR910 device codes. Add the code tables from both, AVR910 and AVR109. Change avr910_devcode of the ATtiny2313 to 0x5e (ATtiny26). Closes bug #16671: Tiny2313 avr910_devcode is bad Closes bug #15826: avr910 device type for ATmega8 wrong 2006-08-21 Joerg Wunsch * avrdude.conf.in: Add (rather conservative) write delay timing values to the *fuse and lock memory spaces of all devices where they have been missing. Add the lock memory space to the ATmega48 section. Closes bug #14920: tiny2313 fuses and AVRDUDE 5.0 Closes bug #15751: atmega48: no lock bits defined 2006-08-21 Joerg Wunsch * avrdude.conf.in: Fix the size of the calibration memory space for ATtiny13, ATmega64, ATmega16, ATmega32, ATmega8535, ATtiny25, ATtiny45, ATtiny85. Closes bug #17383: Wrong calibration section in avrdude.conf... 2006-08-21 Joerg Wunsch * avrdude.conf.in (ATmega324): Correct the pagesize from 256 to 128. This closes bug #16410: ATMega164/324/644 cannot be programmed 2006-08-20 Joerg Wunsch * configure.ac: Check for gettimeofday(). * ppiwin.c (gettimeofday): Define gettimeofday() replacement only if !defined(HAVE_GETTIMEOFDAY); use correct protype. 2006-08-18 Joerg Wunsch * stk500v2: Minor cosmetic changes: STK500 firmware version numbers are M.NN, so always display the minor number as two digits. Examine the response to the sign-on command to see which programmer hardware we are talking to, and then restrict the STK500 topcard display to devices detected as STK500. 2006-08-18 Joerg Wunsch * Makefile.am: Add a dist-hook, and make it remove lexer.c, config_gram.c, and config_gram.h from the source distribution archive. These files are supposed to be generated on the target system. Closes bug #15536: avrdude-5.1 compilation fails on Gentoo/amd64 2006-08-17 Joerg Wunsch * stk500v2.c: unreverse the argument order for CMD_CHIP_ERASE_HVSP; Atmel says AVR068 is right, and stk500.exe is wrong. * configure.ac (AC_CHECK_LIB[usb]): Fix the generation of HAVE_LIBUSB in ac_cfg.h. 2006-08-17 Joerg Wunsch Submitted by Neil Davey: patch #4539: Ability to control the bit clock (usleep) delay for ppi interface * bitbang.c: Implement bitbang_delay() and its calibration. * bitbang.h: Declare bitbang_delay(). * main.c: Add the ispdelay option (-i). * pgm.h (struct programmer_t): Add the ispdelay parameter. * par.c: Add calls to bitbang_delay() when requested. * serbb_posix.c: (Ditto.) * serbb_win32.c: (Ditto.) * avrdude.1: Document the new -i option. * doc/avrdude.texi: (Ditto.) 2006-08-14 Joerg Wunsch Submitted by : * avrdude.conf.in (ATmega48, ATmega88, ATmega168): patch #5100: mega88 EEPROM support (extended for ATmega48 and ATmega168 - jw). 2006-08-14 Joerg Wunsch Submitted by : * stk500v2.c (stk500v2_open): patch #5273: Emit error message if user requests usb and no libusb support 2006-08-14 Joerg Wunsch * avrdude.conf.in: Add HVSP/PP mode parameters for all AVRs. 2006-08-13 Joerg Wunsch * tools: New directory. * tools/get-hv-params.xsl: New file, extract high-voltage programming parameters from Atmel XML files, and produce an avrdude.conf[.in] snippet. 2006-08-11 Joerg Wunsch * configure.ac (AC_CHECK_LIB([usb]): implement a private LIBUSB macro to add this library to, to prevent it from being automatically linked to all binaries. This should fix the Win32 build of loaddrv. * Makefile.am (avrdude_LDADD): add LIBUSB here. 2006-08-10 Eric B. Weddington Contributed by Bob Paddock * avrdude.conf.in: Patch #4780. Provide support for mega325, mega3250, mega645, mega6450. 2006-08-10 Joerg Wunsch * avrdude.conf.in (ATtiny11): fix the HVSP control stack, add delay values required for flash and EEPROM. * stk500v2.c: reverse the argument order for CMD_CHIP_ERASE_HVSP; AVR068 and stk500.exe differ here. 2006-08-09 Joerg Wunsch * stk500v2.c (stk500v2_program_enable): Fix a typo (synchloops vs. synchcycles). 2006-08-04 Joerg Wunsch * avrdude.conf.in: Add parallel programming definitions for the ATmega8/48/88/168. 2006-07-22 Joerg Wunsch * avrdude.conf.in: Add the ATtiny11, an HVSP-only device. 2006-07-21 Joerg Wunsch Implement STK500 (v2) HVSP mode. * stk500v2.c: Add new functions for HVSP support. * stk500v2.h: Add prototype for the stk500hvsp programmer. * avrpart.h: Add fields to struct avrpart for new features. * config_gram.y: Extend the configuration syntax for new features required for HVSP support. * lexer.l: (Ditto.) * avrdude.conf.in: Add HVSP support for ATtiny13 and ATtiny45 as an example. * avrdude.1: Document stk500hvsp. * doc/avrdude.texi: (Ditto.) 2006-07-21 Joerg Wunsch * avrpart.c: Print the very verbose memory details only in debug level > 4. 2006-07-19 Joerg Wunsch * stk500v2.c: Add more parameters for PP mode. Fix the non-paged write operations for old AVRs. * lexer.l: Add more parameters for PP mode. * config_gram.y: (Ditto.) * avrpart.h: (Ditto.) * avrdude.conf.in: Use the new PP mode parameters; add PP mode definitions for AT90S8515. * avrdude.1: Document the stk500pp support. * doc/avrdude.texi: (Ditto.) 2006-07-19 Joerg Wunsch * stk500v2.c: Hide stk500v2_set_sck_period_mk2() behind an #if defined(HAVE_LIBUSB) as it is only used there (for the AVRISP mkII). 2006-07-17 Joerg Wunsch * stk500v2.c: Fix all bugs in stk500pp. Eliminate pagebuf, and use a stack-allocated buffer instead, as the pagesize can be at most 256 for all current AVRs anyway. 2006-07-17 Joerg Wunsch * main.c: Use mem->desc in place of upd->memtype in more places to give the full name of the respective memory area, instead of the (possibly abbreviated) name the user typed in the -U option. 2006-07-16 Joerg Wunsch First stab at an implementation of the STK500 parallel programming feature (v2 firmware only), named "stk500pp". Still not yet complete: EEPROM writes not working, documentation missing, only ATmega16 parameters available in avrdude.conf.in, some parameters not yet implemented. * avrdude.conf.in: Add sample parameters for PP mode to ATmega16. * avrpart.h: Add the parallel programming control parameters. * avrpart.c: (Ditto.) * config_gram.y: Add stk500pp configuration grammar. * lexer.l: Add stk500pp token recognition. * stk500v2.h: Add declaration for stk500pp_initpgm(). * stk500v2.c: Add stk500pp implementation. 2006-07-11 Joerg Wunsch * avrdude.conf.in: Fix the signatures for the ATmega164/324 devices. 2006-07-10 Joerg Wunsch * avrdude.conf.in: Enter the signatures for the ATmega164/324/644 devices. 2006-05-25 Joerg Wunsch * stk500v2.c: Implement extended addressing needed for the ATmega256x devices. * avrdude.1: Document ATmega256x support. * doc/avrdude.texi: Document ATmega256x support. Also document Solaris port defaults. 2006-05-24 Joerg Wunsch * avr.c: Start implementing support for ATmega256x; jtag2 and bitbang programmers are working, stk500v2 still needs to be done. * avrdude.conf.in: (Ditto.) * avrpart.c: (Ditto.) * avrpart.h: (Ditto.) * config_gram.y: (Ditto.) * lexer.l: (Ditto.) 2006-04-18 Joerg Wunsch Contributed by Julius Luukko : * avrdude.conf.in: Add the "ere-isp-avr" programmer. 2006-04-13 Joerg Wunsch * par.c: Add logic to negate parallel-port signals in avrdude.conf using a tilde. Contributed by Bram Daams: * avrdude.conf.in: Add the "atisp" programmer entry that makes use of negated signals. 2006-03-28 Joerg Wunsch * avrdude.conf.in: Add entries for AT90USB{64,128}{6,7} 2006-03-23 Colin O'Flynn Contributed by Wim Lewis, fix a few typos (patch #4987) * avrdude.1: Typo fix 2006-02-27 Colin O'Flynn Contributed by Wim Lewis, add support for checking device signatures in detail (patch #4924 and #4925) * avrdude.conf.in: Add signatures * avrpart.c: Set default signature * avrpart.h: Variable for signature * config_gram.y: More signature reading * lexer.l: Define that signatures exist * main.c: Read signatures and check them against hardware 2006-02-21 Joerg Wunsch * avrdude.conf.in: Fix paged flash write for AT90PWMx (error in datasheet). 2006-01-23 Joerg Wunsch * configure.in: Bump version. 2006-01-17 Colin O'Flynn * main.c: Fixed a typo in safemode variable names, fixed bug 15113 * avrdude.conf.in : Added BS2 and pagel to M162, Patch 4766 * main.c, stk500v2.c: Added patch 4804 from eolson@mit.edu Which stops sck from being writtend needlessly 2006-01-13 Joerg Wunsch Contributed by David Moore: add support for the AVRISP mkII device. (Savannah patch #4789.) * serial.h: Declare usb_serdev_frame device descriptor. * stk500v2.c: Implementation of the AVRISP mkII handling. * usb_libusb.c: Add USB handling for short-frame delimited AVRISP mkII USB protocol; add distinction of different devices in usbdev_open(). * jtagmkII.c: Tell usbdev_open() to search for the JTAG ICE mkII. * usbdevs.h: (New file.) * Makefile.am: Add usbdevs.h, as well as some other forgotten files "make distcheck" complained about. * avrdude.conf.in: Add more aliases for the AVRISP mkII. * avrdude.1: Document how to use the AVRISP mkII. * doc/avrdude.texi: (Ditto.) 2006-01-12 Joerg Wunsch * avrdude.conf.in: Add EEPROM page instructions for the ATmega169 so it will work for STK500v2. 2005-12-16 Joerg Wunsch * avrdude.conf.in: Added support for ATtiny24/44/84. 2005-12-05 Colin O'Flynn * avrdude.conf.in: Added m162 support for stk500v2 2005-12-01 Joerg Wunsch * avrdude.conf.in: fix the number of significant bits for the efuse memory in ATmega48/88/168; the datasheet is a bit off here as well. 2005-11-29 Joerg Wunsch * avrdude.1: update for JTAG ICE mkI support. * doc/avrdude.texi: (Ditto.) 2005-11-29 Joerg Wunsch Submitted by Galen Seitz: patch #4459: Fix for rpm package builds * avrdude.spec.in: update the RPM spec file: - Default to enable-doc=yes during configure. - Move info file to docs package. - Make building of docs package conditional. Basic idea copied from avr-gcc. 2005-11-29 Joerg Wunsch Submitted by someone who thinks he's called "Daper": Fix bug #15013: Wrong use of PPICLAIM (kernel: ppdev0: claim the port first) * par.c: don't claim/release here (thus win_ppdev.h not needed anymore) * ppi.c: claim/release here. * freebsd_ppi.h: ppi_claim/ppi_release now take an fd as parameter. * solaris_ecpp.h: (Ditto.) * linux_ppdev.h: (Ditto.) (Also add copyright.) * win_ppdev.h: Not needed anymore, remove. 2005-11-28 Joerg Wunsch * jtagmkI.c: Improve the communication startup with the ICE. 2005-11-28 Joerg Wunsch * configure.ac: enable parport access on x86_64 Linux and FreeBSD systems. 2005-11-27 Joerg Wunsch * avrdude.conf.in: add the "calibration" space to ATmega16. 2005-11-25 Colin O'Flynn Fixed bug 15051, building for Windows breaks. * par.c: ppi_claim and ppi_release definitions now in a Windows header file * ppi.c: Only included if you are building for Windows * win_ppdev.h: Initial Commit, see par.c 2005-11-24 Joerg Wunsch Add basic support for the Atmel JTAG ICE mkI: * config_gram.y: add mkI support to config sytax. * lexer.l: (Ditto.) * avrdude.conf.in: add sample programmer entries. * jtagmkI.c: New file * jtagmkI.h: New file * jtagmkI_private.h: New file * Makefile.am: include new files in build. 2005-11-24 Colin O'Flynn Fix bug 14681 - Serial Communication Fails on -vvvv with Windows * ser_win32.c: Patched with Brian Dean's patch 2005-11-05 Colin O'Flynn Patch #4532 by Manfred Bartz * avrdude.conf.in: added support for ATMega168 (also added support for the stk500v2 protocol which was not in the patch). 2005-11-03 Joerg Wunsch Add ecpp(7D) (parallel port) for Solaris. * configure.ac: add Solaris' default parallel port. * linux_ppdev.h: change parallel port access to the new style. * freebsd_ppi.h: New file, abstract FreeBSD's ppi(4). * solaris_ecpp.h: New file, abstract Solaris' ecpp(7D). * par.c: change header inclusion sequence. * pgm.h: remove obsolete ppi_claim() and ppi_release() dummies. * ppi.c: change header inclusion sequence, use new parport abstraction, drop obsolete dummy implementation. 2005-11-02 Joerg Wunsch * config.h: change YYSTYPE to be a single word, to work around a bug in Solaris' yacc. * lexer.l: remove incompatibilities with Solaris' default lex, bump resource limits for lex. 2005-11-01 Joerg Wunsch Make avrdude Solaris-compatible. * Makefile.am: distclean avrdude.conf. * avrdude.conf.in: make the parallel-port programmers optional. * bitbang.c: move the bitbang features out into PROGRAMMER. * configure.ac: introduce --enable-parport, add Solaris. * lexer.l: replace str by strng to work around problems in some versions of flex. * main.c: move getexitspecs into the respective programmer's domain; replace rindex by the C-standard strrchr. * par.c: make parallel port optional. * par.h: everything but par_initpgm() is private now. * pgm.h: add setping/getping/highpulsepin/getexitspecs. * serbb_posix.c: generalize bitbang interface; replace cfmakeraw() by explicit code. * serbb_win32.c: generalize bitbang interface. 2005-10-20 Joerg Wunsch * butterfly.c: fix yet another sign extension bug. 2005-10-14 Joerg Wunsch * avrdude.conf.in (ATmega8515): fix size of calibration memory. 2005-10-09 Joerg Wunsch * avrdude.conf.in: add support for ATmega640/1280/1281. * avrdude.1: document the above. * doc/avrdude.texi: (Ditto.) 2005-09-27 Joerg Wunsch * doc/avrdude.texi: Polish up the docs a bit. Use smallexample instead of example for wide tty output. Document a trick to find out about the serial numbers of all JTAG ICEs attached to USB. 2005-09-26 Joerg Wunsch * jtagmkII.c (jtagmkII_paged_write): default the page size early so the buffer will be allocated correctly. * usb_libusb.c: fix libusb handling; now it works with libusb-win32 as well. 2005-09-21 Joerg Wunsch * main.c(do_op): use mem->desc in place of upd->memtype to give the full name of the respective memory area, instead of the (possibly abbreviated) name the user typed in the -U option. 2005-09-21 Joerg Wunsch * main.c: Add the forgotten -B option to the option string in getopt(); sort the -s option into order. 2005/09/21 Brian S. Dean * avr.c: * main.c: * safemode.c: * safemode.h: * term.h: This is Colin O'Flynn's mega patch for updating safemode support: * add support for parts with just 'fuse' memory * if any fuse memories are altered, reflect those changes in the post-programming safemode check so that safemode no longer complains about fuses which were intentionally altered; this eliminates the need to completely disable safemode using -u in order to program fuses. * provide -s option which will not ask to restore fuses, it will just do it 2005-09-19 Joerg Wunsch * butterfly.c (butterfly_initialize): make the device code unsigned so it wouldn't sign-extend when >= 0x80. 2005-09-18 Joerg Wunsch Add the serial bit-bang driver, contributed by Michael Holzt. * bitbang.h: New file. * bitbang.c: New file. * serbb.h: New file. * serbb_posix.c: New file. * serbb_win32.c: New file. * Makefile.am: Include new files. * config_gram.y: Add serbb to configuration language. * lexer.l: (Ditto.) * par.c: Centralize bit-bang code in bitbang.c. * par.h: Declare newly published functions. * pgm.h (struct programmer_t): Add a flag field for private use by the programmer. * pindefs.h: Add definitions for negated serbb pins. * avrdude.conf.in: Add serbb programmers ponyser, dasa, and dasa3. * avrdude.1: Document serbb code. * doc/avrdude.texi: (Ditto.) 2005/09/18 Brian S. Dean * avrdude.conf.in: Patch #4078: add VCC pin definition for DAPA programmer. 2005/09/18 Brian S. Dean * avr910.c: This is patch #3277 which appears to fix a number of issues with the avr910 programmer. Fixes the following problems with paged writes in avr910.c: - failure to re-set address after page writes; - no polling or delay after page writes; - no page writes when not using auto-increment; - an extraneous page write when data ends on page boundary. 2005-09-17 Joerg Wunsch * avrdude.conf.in: Fix the poll values for the ATmega103's EEPROM so they eventually match the XML file. This fixes bug #7492: EEPROM writing fail on atmega103 with atavrisp 2005-09-17 Joerg Wunsch * avrdude.conf.in: The ATmega128 has four oscillator calibration bytes, not only a single one. This closes bug #11496: Memory bank calibration on atmega128 should have 4 bytes 2005/09/17 Brian S. Dean * avrdude.1: Document -q -q. Expand a little on the description of the 'part' command. 2005/09/16 Brian S. Dean * fileio.c: * main.c: Implement -q -q to be very very quiet. 2005/09/16 Brian S. Dean * avrdude.conf.in: Add DAPA programmer. 2005/09/16 Brian S. Dean * avrdude.conf.in: * stk500v2.c: This fixes EEPROM access using the STK500V2 programmer, partially undoing part of a previous general fixup commit. Choose the correct read/write operations with the stk500v2 program function - the correct one depends on the memory type. EEPROM is byte addressable so uses read/write. FLASH is word addressable and so uses read_lo/write_lo. 2005-09-16 Joerg Wunsch * avrdude.1: document the memtypes for -U * doc/avrdude.texi: (Ditto.) Closes bug #13501: should be listed in the man page 2005-09-16 Joerg Wunsch * doc/Makefile.am: add logic to detect the misf^H^H^H^H gratitous API change in recent versions of texi2html where the output directory has changed names. Fix for: bug #13026: The build fails with texi2html 1.76 bug #12715: make issues during install patch #3091: commandline fix for latest version of texi2html 2005-09-16 Joerg Wunsch * usb_libusb.c (usbdev_drain): actually implement draining to aid synchronizing against a JTAG ICE in weird state. 2005-09-16 Joerg Wunsch * butterfly.c: improve the butterfly initialization so it is more likely to synchonize; [bug #9787: avrdude 4.4.0 correct butterfly interface] 2005-09-14 Joerg Wunsch * jtagmkII.c (jtagmkII_paged_load): return the number of bytes read. This makes EEPROM block reads work again. 2005-09-14 Joerg Wunsch * avrdude.conf.in: add a jtag2slow programmer alias, and make "jtag2" default to 115200 Bd. * doc/avrdude.texi: document the above changes. 2005/09/14 Brian S. Dean * avrdude.conf.in: Change bit 0 of the ATmega169 efuse 'write' opcode from 'x' (ignore) to 'i' (input). Even though this bit should be ignored, it should not be changed. The 'x' setting sets the bit to zero which programs it and could cause undefined behaviour. Setting to 'i' enables it to be rewritten to its old value. A better solution might be to read the fuse byte, apply the new value while leaving the 'x' bit alone, then writing the value back. The current fix is a workaround which allows the developer to change the bit as desired. 2005-08-30 Joerg Wunsch * usb_libusb.c: Consistently use unsigned char for buffers. 2005-08-29 Brian S. Dean * avr910.c: Eliminate compiler warnings. GCC 4.x elicits many signedness warnings when passing unsigned char * when char * is in the prototype and vice versa. Clean these up along with a few others. * butterfly.c: (Ditto.) * jtagmkII.c: (Ditto.) * safemode.c: (Ditto.) * safemode.h: (Ditto.) * ser_posix.c: (Ditto.) * serial.h: (Ditto.) * stk500.c: (Ditto.) * stk500v2.c: (Ditto.) 2005-08-28 Joerg Wunsch * avrdude.conf.in: Add support for the ATtiny25/45/85. Note that only the ATtiny45 appears to have a complete XML description right now. * avrdude.1: Mention all the recently added device support: AT90PWM2/3, ATmega164/324/644, ATmega329x/649x, ATtiny25/45/85. * doc/avrdude.texi: (Ditto.) 2005/08/28 Brian S. Dean * avrdude.conf.in: * stk500v2.c: This is patch # 4338, obsoletes patch #4327, provides fixes for bugs #13693, #13871, and #14212. This provides bug fixes to the STK500V2 programmer type. - incorrect token used from avrdude.conf.in - wrong command sent to programmer, hence no write to eeprom. - programmer was said to start writing at 0x0000 and continue page by page and was not repositionned when a gap was found in the hex file, or when the hex file start address was not 0x0000. Hence the verify procedure was correct, not the write procedure. - speed up of flash write to skip empty pages (full of 0xFF) by re-enabling a dedicated function for that task. - stk500v2_paged_load() was not returning the number of byte read, so empty hex files were generated when reading memory. 2005-08-17 Joerg Wunsch * avrdude.conf.in: fix the EEPROM size for ATmega329x/649x. 2005-08-16 Joerg Wunsch * avrdude.conf.in: Add support for the AT90PWM2/3. 2005-07-27 Joerg Wunsch (This work has been done as part of a contract with Atmel, Dresden.) * butterfly.c: Implement full support for AVR109 boot loaders. * avrdude.conf.in: add avr109 and avr911 as alias for butterfly. * avrdude.1: Document the AVR109 addition. * doc/avrdude.texi: (Ditto.) 2005-07-26 Brian S. Dean * main.c: Don't call exit() directly here - set the exit value and jump to the main_exit: label to ensure the programmer is released correctly. * stk500v2.c: The stk500v2_getsync() function was improperly checking for success, thus it was falsely reporting that it failed when it was actually working correctly. Fixed. 2005-07-25 Joerg Wunsch * usb_libusb.c: Catch benign errors when reading the serial #. 2005-06-19 Joerg Wunsch * Makefile.am: Implement libusb-base USB transport for the JTAG ICE mkII. * configure.ac: ditto. * jtagmkII.c: ditto. * ser_posix.c: ditto. * ser_win32.c: ditto. * serial.h: ditto. * usb_libusb.c: ditto (New file). * avrdude.1: document the USB transport. * doc/avrdude.texi: ditto. 2005-06-15 Joerg Wunsch * avrdude.conf.in: The AT90CAN128 has AllowFullPageBitstream = no. 2005-06-14 Joerg Wunsch * avrdude.conf.in: Add support for the ATmega164/324/644. * jtagmkII.c: If enter_progmode fails with RSP_ILLEGAL_JTAG_ID, give the user a hint that the JTAGEN fuse might be unset. 2005-06-11 Joerg Wunsch * avrdude.conf.in: Add support for the ATmega329x/649x. 2005-05-27 Joerg Wunsch * jtagmkII.c: fix a signedness bug when shifting bits; when discarding a packet for being overly long, restart the state machine instead of attempting to drop a preposterous amount of data. 2005-05-19 Joerg Wunsch * avrdude.1: * doc/avrdude.texi: Document that the JTAG ICE mkII code currently cannot write to flash one byte at a time. Also mention the bug tracker interface on savannah. 2005/05/14 Brian S. Dean * configure.ac: * main.c: Update version for beta release and copyright message. Change the default port to 'serial' for the newly added serial programmers stk500v2 and jtagmkii. 2005-05-10 Joerg Wunsch * Makefile.am: * avr910.c: * avrdude.1: * avrdude.conf.in: * avrpart.c: * avrpart.h: * butterfly.c: * config_gram.y: * crc16.c: * crc16.h: * jtagmkII.c: * jtagmkII.h: * jtagmkII_private.h: * lexer.l: * main.c: * pgm.h: * serial.h: * ser_posix.c: * ser_win32.c: * stk500.c: * stk500v2.c: * stk500v2.h: * stk500v2_private.h: * doc/avrdude.texi: Mega-commit to bring in both, the STK500v2 support from Erik Walthinsen, as well as JTAG ICE mkII support (by me). Note that for the JTAG ICE, I did change a few things in the internal API. Notably I made the serial receive timeout configurable by the backends via an exported variable (done in both the Posix and the Win32 implementation), and I made the serial_recv() function return a -1 instead of bailing out with exit(1) upon encountering a receive timeout (currently only done in the Posix implementation). Both measures together allow me to receive a datastreem from the ICE at 115 kbps on a somewhat lossy PCI multi-UART card that occasionally drops a character. The JTAG ICE mkII protocol has enough of safety layers to allow recovering from these events, but the previous code wasn't prepared for any kind of recovery. The Win32 change for this still has to be done. 2005/02/11 Brian S. Dean * main.c: Exit non-zero if safe-mode reverts fuse bits that were requested on the command-line. Variable declarations must only appear at the beginning of a block. 2005/02/10 Brian S. Dean * avrdude.1: Document -u option to disable safe mode. 2005/02/10 Brian S. Dean * configure.ac: doc/Makefile is now dependent on whether or not doc is enabled. 2005/02/10 Brian S. Dean * Makefile.am: * configure.ac: Disable the doc build by default; the tools needed to build doc are either not available on all systems or are at best inconvenient to build and install. The doc can still be built, one just needs to specify --enable-doc at configure time. 2005-01-24 Colin O'Flynn * main.c: Add "safe mode". Fuse settings will be restored at the end of a programming session unless the -u switch is specified. * safemode.c: New file. Safe mode support. * safemode.h: New file. Safe mode support. * Makefile.am: Add new files. * doc/avrdude.texi: Document new Safe Mode feature and switch. 2004/12/22 Brian S. Dean * avrdude.conf.in: Add support for "Xilinx JTAG cable". Contributed by: Tymm Add support for the AT90CAN128. Not sure if all the instruction encoding is correct, specifically the address bits don't exactly match those of the preliminary datasheet that I have, but I don't see how they could be right. Tested with STK500 and it works there. Instruction encodings have not been tested due to lack of a parallel port on my Mac development box. 2004-07-19 Theodore A. Roth * avrdude.1: Remove reference to ppi programmer schematic. * configure.ac (AC_INIT): Set version to "4.4.0cvs". 2004-07-18 Theodore A. Roth * AVRDUDE 4.4.0 has been released (cvs release tag is "release_4_4_0"). 2004-07-18 Theodore A. Roth * Makefile.am (EXTRA_DIST): Remove avrdude.pdf since it is no longer supplied. * NEWS: Fix typo. * bootstrap: Delete the autom4te.cache dir before running the autotools. * configure.ac (AC_INIT): Set version to 4.4.0. 2004-07-17 Jan-Hinnerk Reichert * avrdude.1: Fixed obvious copy and paste error (Patch #3199 contributed by Galen Seitz) 2004-07-15 Theodore A. Roth * main.c (main): Don't indent CPP directives. When showing update progress in a no tty situation, use unbuffered IO for all systems, not just win32 native. Update copyright year when printing version. Remove warning about native win32 being experimental. Split a line string. * ppiwin.c: Update copyright year. Add cvs Id keyword. (usleep): Cleanup debug CPP directives to improve readability. * ser_win32.c: Include to fix failing build. 2004-07-08 Theodore A. Roth * AUTHORS: Add names of recent major contributors. * ser_win32.c: Assign copyright to Martin J. Thomas since he did all real work on this file. 2004-07-07 Jan-Hinnerk Reichert * NEWS, doc/TODO: Updated NEWS and TODO 2004-07-07 Jan-Hinnerk Reichert * stk500.c, term.c, doc/avrdude.texi, avrdude.1: added "sck"-command to the terminal mode. This command allows slowing down of the SCK of STK500-programmers. 2004-07-05 Jan-Hinnerk Reichert * *.c, *.h: Removed unnecessary includes of config.h 2004-07-04 Jan-Hinnerk Reichert * avr.h: Removed some unused prototypes 2004-07-04 Jan-Hinnerk Reichert * stk500.c: Fixed fosc behaviour for values exceeding maximum frequency (contributed by Galen Seitz) 2004-07-04 Jan-Hinnerk Reichert * avrdude.conf.in: Added support for ATtiny2313 (contributed by Bob Paddock) 2004-06-25 Joerg Wunsch * avrdude.conf.in: Fix efuse bits for ATmega169. 2004-06-24 Alex Shepherd Merged in Win32 Native changes contributed by Martin Thomas Changed all instances of __CYGWIN__ conditional compilation to WIN32NATIVE * ser_win32.c: fleshed out all the previous stubs * ser_posix.c: added WIN32NATIVE conditional compilation to skip all function to allow ser_win32.c functions to operate * ppi.h: removed commented code * pgh.h: added usleep macros * main.c: stdout,stderr tweaks for Win32 * configure.ac: added CFLAGS and LDFLAGS for Win32Native * config_gram.y: added strtok_r macro * buterfly.c: added various stub functions and EXIT processing * avr910.c: added return 0 to avr910_open() and included time headers * term.c: added warning about libreadline not supported in WIN32NATIVE 2004-06-17 Jan-Hinnerk Reichert * avrdude.conf.in: Added support for - tiny13 (contributed by Pawel Moll) - mega48 and mega88 (contributed by Galen Seitz) However, the STK500-code for mega8 remains unchanged. 2004-05-19 Brian S. Dean * main.c: * stk500.c: Allow the baud rate to be specified on the command line with a new -b switch. The specified baud rate will override the default serial port baud rate for a particular programmer. 2004-05-19 Brian S. Dean * ppi.c: Stub-out the ppi_* functions in ppi.c with empty wrappers that simply return an error code in order to build successfully on MacOS X. This allows avrdude to work on MacOS X and was tested using a USB<->RS232 cable adapter, specifically Keyspan model USA-19HS. 2004-04-23 Joerg Wunsch * lists.h, lists.c: Drop LISTSZ and the check for it in lcreat(). 2004-04-17 Jan-Hinnerk Reichert * avr910.c: Hopefully fixed that weird "first byte not programmed"-error in a good way (previous fix was not working with all firmwares) 2004-02-10 Jan-Hinnerk Reichert * avrdude.1, doc/avrdude.texi, doc/TODO: Removed the deprecated options from documentation 2004-02-10 Jan-Hinnerk Reichert * main.c: Removed deprecated options. 2004-01-28 Jan-Hinnerk Reichert * pgm.c, main.c, avr910.c, butterfly.c, stk500.c: Changed default for powerup, powerdown and LED-commands to do nothing and return OK. Then removed these commands from avr910, butterfly and stk500. * pgm.c: Fixed wrong type for default_open introduced by the cleanup yesterday. 2004-01-29 Jan-Hinnerk Reichert * par.c: changed order of port-read/writes in par_txrx(). This change should increase immunity to delays in the programmer-hardware. Also did some unrelated cleanup in par_txrx(). 2004-01-28 Jan-Hinnerk Reichert * pgm.[ch], main.c, par.c, avr910.c, butterfly.c, stk500.c: Move save/restore-functionality into open/close. * par.c: open/close now saves/restores PPICTRL, too. * TODO: exitspecs don't work if RESET is in PPICTRL. 2004-01-26 Theodore A. Roth * configure.ac (AC_INIT): Post release version update. 2004-01-26 Theodore A. Roth * AVRDUDE 4.3.0 has been released (cvs release tag is "release_4_3_0"). 2004-01-26 Theodore A. Roth * configure.ac: Update copyright year. (AC_INIT): Set version to 4.3.0. 2004-01-25 Theodore A. Roth * ChangeLog: Minor formatting cleanups. Move to all 2003 entries to ChangeLog-2003. * ChangeLog-2003: New file. * Makefile.am: Update copyright year. (EXTRA_DIST): Add ChangeLog-2003. 2004-01-17 Jan-Hinnerk Reichert * doc/avrdude.texi: Get rid of those black boxes marking "overfull hbox". 2004-01-17 Jan-Hinnerk Reichert * doc/avrdude.texi: New appendix "Troubleshooting". 2004-01-12 Jan-Hinnerk Reichert * avr910.c, avrpart.c, avrpart.h, doc/TODO: Look up devicecode and report device. 2004-01-03 Jan-Hinnerk Reichert * avr910.c, pgm.c, pgm.h, config_gram.y, lexer.l: Add new configuration parameter baudrate to support avr910-programmers with non-standard baudrates. * avrdude.conf.in, doc/avrdude.texi: Added "baudrate" to documentation. 2004-01-03 Jan-Hinnerk Reichert * avr910.c: Removed debugging stuff that is no longer needed. 2004-01-03 Jan-Hinnerk Reichert * doc/TODO: Removed two items. 2004-01-03 Jan-Hinnerk Reichert * main.c, avr.c, avr.h, par.c, stk500.c: Add function avr_chip_erase() to unify handling of cycle-count. Makes cycle-count work for avr910-programmers.