* jtag3.c (jtag3_edbg_recv_frame): Return correct length as
reported in the response packet, rather than full 512 byte which
are always reported by the CMSIS-DAP layer. Miscalculations
based on the wrongly reported length caused heap corruption
elsewhere, so this is presumably also a fix for bug #43078.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1344 81a1dc3b-b13d-400b-aceb-764788c761c2
flash page
* usbasp.c (usbasp_spi_paged_write): Remove USBASP_BLOCKFLAG_LAST.
It is no longer needed, as we always write full pages now in paged
write mode.
This prevents each flash page from being written twice, where the
second attempt on older devices (ATmega64/128) signalled an immediate
"ready" condition when polling (likely a silicon bug) even though they
were still in progress. This caused the USBasp firmware to proceed,
and fill the page buffer anew which eventually caused the data
corruption.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1343 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk500v2_recv): Add a reference to the bug report
but don't change anything, lest to break it somehow
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1342 81a1dc3b-b13d-400b-aceb-764788c761c2
* avr.c: avoid division by zero in report_progress(), eg. when
writing an empty eeprom file were total becomes 0
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1340 81a1dc3b-b13d-400b-aceb-764788c761c2
* buspirate.c: applied patch + switch off at disable (even when
a reset follows) + some general whitespace/tab cleanup
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1339 81a1dc3b-b13d-400b-aceb-764788c761c2
after changing lock byte
* stk500v2.c (stk500isp_write_byte): As a workaround for broken
tool firmware, add 10 ms of delay before returning from any
single-byte write operation.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1337 81a1dc3b-b13d-400b-aceb-764788c761c2
every byte-wide access (rather than JTAGICE3 only). This finally
obsoletes the use of the prehistoric SPI_MULTI command where
AVRDUDE used to assemble all the low-level ISP stuff by itself.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1336 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (m168, m328, m48, m88, t1634, t26, t261, t461,
t861, t88): In efuse (or hfuse for t26) read operation, turn all
bits in byte 3 from "x" to "o" (output); this is a first step
towards fixing the symptoms mentioned in the bug, by unifying the
behaviour between different AVRs. Not touched are the historic
devices where the fuses are not documented to form a full byte
each (2333, 4433, 4434, 8535, m103, m161, m163).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1335 81a1dc3b-b13d-400b-aceb-764788c761c2
* usb_libusb.c (usbdev_drain): Make this a dummy function only.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1334 81a1dc3b-b13d-400b-aceb-764788c761c2
When printing the part signature also print the part id.
* avrpart.c (locate_part_by_signature): New function.
* libavrdude.h (locate_part_by_signature): New function.
* main.c (main): Use the new function to find the part and print its id.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1332 81a1dc3b-b13d-400b-aceb-764788c761c2
* ft245r.c: set pthread cancel type to asynchronous, reorder ftdi_usb_close/deinit
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1324 81a1dc3b-b13d-400b-aceb-764788c761c2
Submitted by Didrik Madheden:
* flip1.c: Provide dummy functions for the #ifndef HAVE_LIBUSB case
* flip2.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1314 81a1dc3b-b13d-400b-aceb-764788c761c2
serial.h fileio.h safemode.h update.h pgm_type.h config.h confwin.h
lists.h) into a single header that can be included by anyone wanting
to link against the library.
Adapt everything to cope with this situation.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1311 81a1dc3b-b13d-400b-aceb-764788c761c2
* configure.ac: Add AC_CONFIG_MACRO_DIR as suggested by libtoolize
* Makefile.am: add -I m4 to ACLOCAL_AMFLAGS as suggested by libtoolize
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1308 81a1dc3b-b13d-400b-aceb-764788c761c2
(in the !HAVE_LIBUSB case) to match prototypes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1303 81a1dc3b-b13d-400b-aceb-764788c761c2
This file will be overwritten by the next installation, so it's not a
good idea to manually modify it. Using the -C +file option is a much
better way for user modifications.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1296 81a1dc3b-b13d-400b-aceb-764788c761c2
will split this according to the EP's maxsize. This makes it work
over USB 1.1 connections (albeit very slowly, due to the interrupt
transfers used).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1284 81a1dc3b-b13d-400b-aceb-764788c761c2
joerg_wunsch
rliebscher
awachtler