programmers)
* config_gram.y: Introduce new keyword "is_at90s1200".
* lexer.l: (Ditto.)
* avrdude.conf.in: Applew new keyword to the AT90S1200 device.
* avrpart.h: Introduce new flag AVRPART_IS_AT90S1200, reflecting
the is_at90s1200 configuration keyword.
* bitbang.c (bitbang_initialize): Replace existing test for
AT90S1200 by AVRPART_IS_AT90S1200
* avr.c (avr_write_byte_default): Avoid the pre-write reading for
the AT90S1200, as this appears to sometimes corrupt the high byte
by pre-programming the low byte just written into it.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1002 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7056: adding support for mikrokopter bootloader to butterfly
* butterfly.c: Add some specific logic to handle the
mikrokopter.de butterfly bootloader.
* butterfly.h: Add one related function declaration.
* config_gram.y: Add butterfly_mk keyword.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add entry for butterfly_mk.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@991 81a1dc3b-b13d-400b-aceb-764788c761c2
Wolfgang Moser, Ville Voipio, Hannes Weisbach
patch #7486: Patch to add FT2232C/D, FT2232H, FT4232H,
usbvid, usbpid, usbdev for USB support - Based on #7062
* avrftdi.c: New file.
* avrftdi.h: (Ditto.)
* configure.ac: Add check for libftdi.
* config_gram.y: Add AVRFTDI and per-programmer USB string
keywords.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add avrftdi and 2232HIO programmers.
* pgm.h: Add USB parameters.
* Makefile.am: Add avrftdi.c and avrftdi.h.
* AUTHORS: Mention the new authors.
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@979 81a1dc3b-b13d-400b-aceb-764788c761c2
Add ATtiny4/5/9/10 to avrdude.conf.in.
Document TPI and new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@916 81a1dc3b-b13d-400b-aceb-764788c761c2
by recent GCC versions).
* config_gram.y (parse_cmdbits): "brkt possibly used uninitialized"
(GCC errs here)
* jtagmkII.c (jtagmkII_reset32): "status possibly used uninitialized"
(I think GCC errs, too)
* buspirate.c: "pointers differ in signedness" (mismatch between
string processing and the use of "unsigned char" throughought the
AVRDUDE API)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@882 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI mode of the STK600 is supported. Single-byte EEPROM
(and flash) updates do not work yet.
* avr.c: "boot" memory is a candidate memory region for paged
operations, besides "flash" and "eeprom".
* avrdude.conf.in: add ATxmega128A1 and ATxmega128A1revD
* avrpart.h: add the AVRPART_HAS_PDI flag (used to distinguish
ATxmega parts from classic AVRs), the nvm_base part field, and
the offset field for a memory region.
* config_gram.y: add "has_pdi", "nvm_base", and "offset"
* lexer.l: (Ditto.)
* main.c: disable auto_erase for ATxmega parts
* stk500v2.c: implement the XPROG functionality, and divert to
this for ATxmega parts
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@777 81a1dc3b-b13d-400b-aceb-764788c761c2
"classic" AVRs (AT90, ATtiny, ATmega) in both,
ISP and high-voltage programming modes.
* Makefile.am: Add -lm.
* avrdude.conf.in: Add stk600, stk600pp, and stk600hvsp.
* config_gram.y: Add support for the stk600* keywords.
* lexer.l: (Ditto.)
* pgm.h: Add the "chan" parameter to set_varef().
* stk500.c: (Ditto.)
* serial.h: Add USB endpoint support to struct filedescriptor.
* stk500v2.c: Implement the meat of the STK600 support.
* stk500v2.h: Add new prototypes for stk600*() programmers.
* stk500v2_private.h: Add new constants used in the STK600.
* term.c: Add AREF channel support.
* usb_libusb.c: Automatically determine the correct write
endpoint ID, the STK600 uses 0x83 while all other tools use
0x82. Propagate the EP to use through struct filedescriptor.
* usbdevs.h: Add the STK600 USB product ID.
* tools/get-stk600-cards.xsl: XSL transformation for
targetboards.xml to obtain the list of socket and routing
card IDs, to be used in stk500v2.c (for displaying the
names).
* tools/get-stk600-devices.xsl: XSL transformation for
targetboards.xml to obtain the table of socket/routing cards
and their respective AVR device support for doc/avrdude.texi.
* avrdude.1: Document all the STK600 stuff.
* doc/avrdude.texi: Ditto. Added a new chapter for
Programmer Specific Information.
Thanks to Eirik Rasmussen from Atmel Norway for his support in
getting this code running within that short amount of time!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@768 81a1dc3b-b13d-400b-aceb-764788c761c2
declarations in each file by a central header file "avrdude.h".
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@721 81a1dc3b-b13d-400b-aceb-764788c761c2
imposed by debugWire itself, so effectively, only flash ROM can be
read and written.
Currently, the required changes to avrdude.conf.in are only present
for the ATtiny44.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@688 81a1dc3b-b13d-400b-aceb-764788c761c2
either firmware version 1 or 2.
* Makefile.am (avrdude_SOURCES): add the new files
stk500generic.c and stk500generic.h.
* avrdude.conf.in: Add the stk500generic programmer type, and
change the "stk500" entry to point to this programmer.
* config_gram.y: Add the stk500generic keyword.
* lexer.l: (Ditto.)
* stk500.c: Change the stk500v1 code to not call exit()
prematurely when failing to open the programmer, but instead
return an error status.
* stk500generic.c: (New file.) Stub programmer implementation.
Probe for either stk500v1 or stk500v2, and adjust the current pgm
appropriately.
* stk500generic.h: (New file.) Declare the public interface(s)
of stk500generic.c.
* doc/avrdude.texi: Document the changed behaviour of stk500.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@663 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #4686: Add support for USBasp, a simple USB programmer
* usbasp.c: New file, implement the USBasp driver.
* usbasp.h: New file, interface declarations for USBasp.
* Makefile.am: Wire the new files into the build.
* avrdude.conf.in: Add the usbasp programmer entry.
* config_gram.y: Add the usbasp token.
* lexer.l: (Ditto.)
* avrdude.1: Document the USBasp programmer.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@656 81a1dc3b-b13d-400b-aceb-764788c761c2
via the patch tracking system.
patch #5096: Allow VCC and BUFF to be any pin in parallel mode
* config_gram.y: Release the restriction to PPIDATA pins.
* par.c: Rework the code to introduce a function par_setmany()
that builds on top of par_setpin(), and use that function for the
PPI_AVR_VCC and PPI_AVR_BUFF pin collections. This also abstracts
the polarity of these signals appropriately.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@628 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c: Add new functions for HVSP support.
* stk500v2.h: Add prototype for the stk500hvsp programmer.
* avrpart.h: Add fields to struct avrpart for new features.
* config_gram.y: Extend the configuration syntax for new
features required for HVSP support.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add HVSP support for ATtiny13 and
ATtiny45 as an example.
* avrdude.1: Document stk500hvsp.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@595 81a1dc3b-b13d-400b-aceb-764788c761c2
Fix the non-paged write operations for old AVRs.
In avrdude.conf.in, use the new PP mode parameters; add PP mode
definitions for AT90S8515.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@591 81a1dc3b-b13d-400b-aceb-764788c761c2
jtag2 and bitbang programmers are working, stk500v2
still needs to be done.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@581 81a1dc3b-b13d-400b-aceb-764788c761c2
Contributed by Wim Lewis, add support for checking device
signatures in detail (patch #4924 and #4925)
* avrdude.conf.in: Add signatures
* avrpart.c: Set default signature
* avrpart.h: Variable for signature
* config_gram.y: More signature reading
* lexer.l: Define that signatures exist
* main.c: Read signatures and check them against hardware
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@573 81a1dc3b-b13d-400b-aceb-764788c761c2
The very basic functionality (paged flash read/write, erase, terminal
mode reads, fuse writes) works fine. There are still the following
issues right now:
. paged EEPROM write (i.e. through -U eeprom:w:...) only works on an
erased EEPROM
. byte-access flash and EEPROM writes (i.e. in terminal mode) fail
. documentation needs to be updated still
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@547 81a1dc3b-b13d-400b-aceb-764788c761c2
will be available in the upcoming avrdude release.
His addition has been implemented by means of a generalized bit-bang
interface that contains the common part between serial and paralle
bit-bang devices, and specialed backends for the serial and parallel
port connections.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@515 81a1dc3b-b13d-400b-aceb-764788c761c2
. Implement the new EECRAddress field in the device descriptor that is
required by the 4.x firmware; make an uneducated guess about what
firmware requires what length of device descriptor -- perhaps Atmel
can be convinced to publish an official matrix for that.
. Specify EECR in the config file where required. Obviously, only
locations that differ from the 0x3c default are mentioned in the
XML files, so by now, this only affects the AT90CAN128 for us.
. After clarification with Atmel, EnablePageProgramming should really
default to 1, and only cleared if specified by an XML parameter. So
far, only the XML files for the ATmega256x and ATmega406 do specify
it at all, and they specify a 1, too.
. Drop the entire OCDEN fuse heuristic. If OCDEN is unprogrammed at
startup, issue a warning that single-byte EEPROM updates won't be
possible. Leave it to the user to program the fuse if desired.
That way, we won't run into any issue of prematurely wearing out the
hfuse EEPROM cell. Interestingly enough, this also solved the
problem of the target not restarting from scratch upon sign-off.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@461 81a1dc3b-b13d-400b-aceb-764788c761c2
Walthinsen, as well as JTAG ICE mkII support (by me).
Erik's submission has been cleaned up a little bit, mostly to add his
name and the current year to the copyright of the new file, remove
trailing white space before importing the files, and fix the minor
syntax errors in his avrdude.conf.in additions (missing semicolons).
The JTAG ICE mkII support should be considered alpha to beta quality
at this point. Few things are still to be done, like defering the
hfuse (OCDEN) tweaks until they are really required. Also, for
reasons not yet known, the target MCU doesn't start to run after
signing off from the ICE, it needs a power-cycle first (at least on my
STK500).
Note that for the JTAG ICE, I did change a few things in the internal
API. Notably I made the serial receive timeout configurable by the
backends via an exported variable (done in both the Posix and the
Win32 implementation), and I made the serial_recv() function return a
-1 instead of bailing out with exit(1) upon encountering a receive
timeout (currently only done in the Posix implementation). Both
measures together allow me to receive a datastreem from the ICE at 115
kbps on a somewhat lossy PCI multi-UART card that occasionally drops a
character. The JTAG ICE mkII protocol has enough of safety layers to
allow recovering from these events, but the previous code wasn't
prepared for any kind of recovery. The Win32 change for this still
has to be done, and the traditional drivers need to be converted to
exit(1) upon encountering a timeout (as they're now getting a -1
returned they didn't see before in that case).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@451 81a1dc3b-b13d-400b-aceb-764788c761c2
available.
* avr910.c (avr910_vfy_cmd_sent): New function.
(avr910_chip_erase): Add support for chip erase.
(avr910_enter_prog_mode): New function.
(avr910_leave_prog_mode): New function.
(avr910_initialize): Add code to select device type and enter prog mode.
(avr910_close): Leave programming mode before closing serial port.
(avr910_read_sig_bytes): New function.
(avr910_initpgm): Add avr910_read_sig_bytes method to pgm initializer.
* avrdude.conf.in: Add note about deprecating devicecode.
Change all occurences of devicecode to stk500_devcode.
Add avr910_devcode to a few parts for testing.
* avrpart.h (struct avrpart): Change devicecode field to stk500_devcode.
(struct avrpart): Add avr910_devcode field.
* config_gram.y: Add K_STK500_DEVCODE and K_AVR910_DEVCODE tokens.
Generate an error if devicecode is found in the config file.
Handle parsing of avr910_devcode and stk500_devcode.
* lexer.l: Handle parsing of avr910_devcode and stk500_devcode.
* pgm.c: Initialize pgm->read_sig_bytes field.
* pgm.h: Add pgm->read_sig_bytes field.
* stk500.c: Use stk500_devcode instead of devicecode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@293 81a1dc3b-b13d-400b-aceb-764788c761c2
* config_gram.y: Add parsing of avr910 programmer.
* lexer.l: Add avr910 token.
* avr910.c: [this is still work in progress]
Add some debug output.
Add probe for programmer presense.
* main.c: Set port to default_serial if programmer type is avr910.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@292 81a1dc3b-b13d-400b-aceb-764788c761c2
causes some shift-reduce conflicts, but I think they are OK.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@255 81a1dc3b-b13d-400b-aceb-764788c761c2
$HOME/.avrduderc. Entries from .avrduderc take precedence over those
from the system wide config file in ${PREFIX}/etc/avrdude.conf.
Track and display the config file name and line number when we print
out the available parts and programmers. This is useful in case
someone has overridden a definition in their .avrduderc file and is
wondering why the definition in the system wide config file is not
being used.
Remove the default programmer 'stk500' from the distributed config
file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@222 81a1dc3b-b13d-400b-aceb-764788c761c2
one of the programmers to be tagged "default" within its definition.
Also, axe the notion of a compiled-in default programmer. It is
kind've pointless now that nearly all configuration comes from the
config file, thus, avrdude is not very useful without the config file,
and thus, having a programmer compiled-in offers little or no benefit.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@218 81a1dc3b-b13d-400b-aceb-764788c761c2
This adds 'default_parallel' and 'default_serial' keywords to the
grammar, which take quoted string arguments.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@214 81a1dc3b-b13d-400b-aceb-764788c761c2
programming mode. Use 'retry_pulse' in the per-part specification
that can currently take values of 'reset' or 'sck', the default being
'sck' which preserves the previous behaviour. Some newer parts
indicate that /RESET should be pulsed, while older parts say to pulse
SCK.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@212 81a1dc3b-b13d-400b-aceb-764788c761c2
Rene Liebscher
Joerg Wunsch
David Hoerl
Michal Ludvig
Colin O Flynn
Brian S. Dean
kiwi64ajs
Jan-Hinnerk Reichert
Theodore A. Roth