* Provide cached byte-wise read/write API
int avr_read_byte_cached(const PROGRAMMER *pgm, const AVRPART *p, const
AVRMEM *mem, unsigned long addr, unsigned char *value);
int avr_write_byte_cached(const PROGRAMMER *pgm, const AVRPART *p, const
AVRMEM *mem, unsigned long addr, unsigned char data);
int avr_flush_cache(const PROGRAMMER *pgm, const AVRPART *p);
int avr_chip_erase_cached(const PROGRAMMER *pgm, const AVRPART *p);
int avr_reset_cache(const PROGRAMMER *pgm, const AVRPART *p);
avr_read_byte_cached() and avr_write_byte_cached() use a cache if paged
routines are available and if the device memory is EEPROM or flash,
otherwise they fall back to pgm->read_byte() and pgm->write_byte(),
respectively. Byte-wise cached read always gets its data from the cache,
possibly after reading a page from the device memory. Byte-wise cached
write with an address in memory range only ever modifies the cache. Any
modifications are written to the device after calling avr_flush_cache() or
when attempting to read or write from a location outside the address range
of the device memory.
avr_flush_cache() synchronises pending writes to EEPROM and flash with the
device. With some programmer and part combinations, flash (and sometimes
EEPROM, too) looks like a NOR memory, ie, one can only write 0 bits, not 1
bits. When this is detected, either page erase is deployed (eg, with parts
that have PDI/UPDI interfaces), or if that is not available, both EEPROM
and flash caches are fully read in, a pgm->chip_erase() command is issued
and both EEPROM and flash are written back to the device. Hence, it can
take minutes to ensure that a single previously cleared bit is set and,
therefore, this routine should be called sparingly.
avr_chip_erase_cached() erases the chip and discards pending writes() to
flash or EEPROM. It presets the flash cache to all 0xff alleviating the
need to read from the device flash. However, if the programmer serves
bootloaders (pgm->prog_modes & PM_SPM) then the flash cache is reset
instead, necessitating flash memory be fetched from the device on first
read; the reason for this is that bootloaders emulate chip erase and they
won't overwrite themselves (some bootloaders, eg, optiboot ignore chip
erase commands altogether) making it truly unknowable what the flash
contents on device is after a chip erase.
For EEPROM avr_chip_erase_cached() concludes that it has been deleted if a
previously cached EEPROM page that contained cleared bits now no longer
has these clear bits on the device. Only with this evidence is the EEPROM
cache preset to all 0xff otherwise the cache discards all pending writes
to EEPROM and is left unchanged otherwise.
Finally, avr_reset_cache() resets the cache without synchronising pending
writes() to the device.
`avrdude.1` is installed into `man` dir instead of its proper section
location.
This is due to the definition of `TYPE MAN` which points to
`<DATAROOT>/man` according to cmake docs.
Use `DESTINATION` and add proper section subdir.
This allows for `man -M <YOUR INSTALL dir>/share/man -w 1 avrdude` to succeed
instead of throwing `No manual entry for avrdude in section 1`
Signed-off-by: brutzzl3r <s3b.gr0ss@gmail.com>
-p \*/c check address bits in SPI commands
-p \*/d description of core part features
-p \*/o opcodes for SPI programming parts and memories
-p \*/s show avrdude.conf entries of parts
-p \*/ss show full avrdude.conf entry as tab separated table
-p \*/w wd_... constants for ISP parts
-p \*/\* all of the above except -p \*/s
-p \* same as -p\*/\*
Fix the following build failure without a C++ compiler:
CMake Error at CMakeLists.txt:24 (project):
No CMAKE_CXX_COMPILER could be found.
Tell CMake where to find the compiler by setting either the environment
variable "CXX" or the CMake cache entry CMAKE_CXX_COMPILER to the full path
to the compiler, or to the compiler name if it is in the PATH.
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
This feature has been designed with the sometimes quite flakey direct
(parallel or serial port attached) bitbang programming adapters in
mind that were quite common about two decades ago.
With parallel ports vanishing from modern PCs almost completely, and
the advent of various USB-attached low-cost programming devices,
this class of programmers disappeared almost completely.
Furthermore, the fuse combinations that were covered by the feature
are no longer around on all recent AVR devices, so for an ever
increasing number of devices, safemode already became meaningless and
was turned off anyway.
With the prospective version 7.x release, it's a good point in time to
introduce a major change like this one.
With the split CMakeLists.txt infrastructure avrdude.conf
will be created in the build/src and not build folder. Hence,
fix its location in the install command.
The main CMakeLists.txt file in the project's root directory takes
care of the main project settings like project name and version,
handling the options, finding dependencies, etc.
The src/CMakeLists.txt handles options that are necessary to build
libavrdude library and avrdude binary.
* Find 'avrdude.conf' based on absolute path to executable
* Update coding style
* Update coding style
* Update 'src/doc/avrdude.texi' to reflect the new search method for 'avrdude.conf'
Since commit ed46f09c1ccd1351e003a200ba50e3e4778ac478 (Implement
tc[io]flush methods & deprecate broken purge_buffers methods.)
ftdi_usb_purge_buffers() routine is deprecated. Use HAVE_FTDI_TCIOFLUSH
macro to invoke the newly introduced ftdi_tcioflush() routine.
Stefan Rueger
Marius Greuel
brutzzl3r
Fabrice Fontaine
Ebben Aries
Jörg Wunsch
Yegor Yefremov
Kristof Mulier