patch #7896: DFU FLIPv2 programming support
* pgm_type.c: Add the flip2 programmer type.
* config_gram.y: Allow for the usbid keyword in a device definition.
* avrdude.conf.in: Add usbpid values to those Xmega devices where
applicable.
* avrpart.h: Add usbpid device field.
* dfu.c: (New file.)
* dfu.h: (New file.)
* flip.c: (New file.)
* flip.h: (New file.)
* Makefile.am: Add new files.
* doc/avrdude.texi: Document the changes.
* avrdude.1: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1258 81a1dc3b-b13d-400b-aceb-764788c761c2
* fileio.c (fileio): open file in binary mode also for FMT_ELF
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1253 81a1dc3b-b13d-400b-aceb-764788c761c2
* linuxgpio.c, bitbang.c, buspirate.c, par.c, pgm.h, term.c, serbb_*.c: changed
interface of setpin, getpin, highpulsepin to take pin function as parameter
(not the real number, which can be found by pgm->pinno[function])
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1252 81a1dc3b-b13d-400b-aceb-764788c761c2
* linuxgpio.c: fixed check for unused pins to ignore the inverse flag
* pindefs.c: fixed fill_old_pinlist to not create an empty mask with inverse flag set
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1251 81a1dc3b-b13d-400b-aceb-764788c761c2
This options was used during developing to examine the created
bytestream - even without an FTDI device present. avrftdi creates
correct bytestreams and thus, this is option is not of any use anymore.
To the contrary: it makes code unreadable, more complex and prone to error.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1246 81a1dc3b-b13d-400b-aceb-764788c761c2
* main.c: Always clear the UF_AUTO_ERASE flag if either a
non-Xmega device was found, or the programmer does not offer a
page_erase method.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1242 81a1dc3b-b13d-400b-aceb-764788c761c2
the flash page cache size to at most "readsize". For Xmegas with
a page size of 512 bytes, the maximum USB packet size was
overflowed, and subsequently, a memmove copied beyond the end of
the allocated buffer.
* jtag3.c (jtag3_read_byte): Add the correct offset also for the
various flash regions, so reading the apptable or boot regions
yields the correct data.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1237 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #40040: Support for ATtiny20 and ATtiny40
* avrdude.conf.in: Restructure the reduced-core tiny devices
to use a common entry .reduced_core_tiny; add ATtiny20 and
ATtiny40
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1236 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #40033: Support for the XMegaE5 family
* avrdude.conf.in (ATxmega8E6, ATxmega16E5, ATxmega32E5): New
entries.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1231 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7710: usb_libusb: Check VID/PID before opening device
* usb_libusb.c (usbdev_open): Swap the sequence of verifying the
VID:PID, and opening the device.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1228 81a1dc3b-b13d-400b-aceb-764788c761c2
* butterfly.c (butterfly_page_erase): Add dummy function to avoid
segfault when writing to EEPROM.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1227 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7657 Add ATmega406 support for avrdude using DRAGON + JTAG
* avrdude.conf.in (ATmega406): New entry.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1225 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_getsync): Loop 10 times trying to get in
sync with the programmer.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1223 81a1dc3b-b13d-400b-aceb-764788c761c2
* avr.c (avr_read, avr_write): Change the progress reporting for
paged read/write from per-address to per-considered-page. This
ought to give a realistic estimation about the time still to be
spent.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1220 81a1dc3b-b13d-400b-aceb-764788c761c2
Add a FAQ entry describing the method to connect to a device
where the firmware has reduced the internal clock speed.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1218 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf: Bump the chip_erase_delay for all ATmega*4 devices
to 55 ms. While the datasheet still claims 9 ms, all the XML files
tell either 45 or 55 ms, depending on STK600 or not.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1217 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtagmkII_private.h (MTYPE_EEPROM_XMEGA): New memory type.
* jtagmkII.c (jtagmkII_write_byte): For Xmega EEPROM, use
memory type MTYPE_EEPROM_XMEGA; for flash writes, always
write 2 bytes starting on an even address.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1212 81a1dc3b-b13d-400b-aceb-764788c761c2
algorithm for EEPROM when being connected through debugWIRE.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1210 81a1dc3b-b13d-400b-aceb-764788c761c2
EEPROM. (Flash cells must have been erased before though.)
* jtag3.c (jtag3_initialize): OCDEN no longer needs to be
considered; a session with "programming" purpose is sufficient
* jtag3.c (jtag3_write_byte): Use the paged algorithm for all
flash and EEPROM areas, not just Xmega.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1209 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtag3_private.h (MTYPE_EEPROM_XMEGA): New define.
* jtag3.c (jtag3_write_byte): When updating flash or
EEPROM on Xmega devices, resort to jtag3_paged_write()
after filling and modifying the page cache.
* jtag3.c (jtag3_paged_write): use MTYPE_EEPROM_XMEGA
where appropriate.
* jtag3.c (jtag3_initialize): Open with debugging intent
for Xmega devices, so single-byte EEPROM updates will
work.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1208 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #38951: AVR109 use byte offset instead of word offset
patch #8045: AVR109 butterfly failing
* butterfly.c (butterfly_paged_load, butterfly_paged_write):
fix calculation of 'A' address when operating on flash memory.
It must be given in terms of 16-bit words rather than bytes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1205 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtag3.c (jtag3_initialize): initialize the eeprom_pagesize
private attribute so the page cache will actually be usable
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1202 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtag3.c (jtag3_read_byte, jtag3_write_byte): Correctly apply the
relevant part of mem->offset as the address to operate on.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1201 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #35800: Compilation error on certain systems if parport is disabled
* linux_ppdev.h: Conditionalize inclusion of <linux/parport.h> and
<linux/ppdev.h> on HAVE_PARPORT
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1198 81a1dc3b-b13d-400b-aceb-764788c761c2
* pickit.c (usb_open_device): Use %p rather than %X to print "handle"
which is a pointer
* jtag3.c (jtag3_initialize): Initialize "flashsize" to be sure it
proceeds with a valid value.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1197 81a1dc3b-b13d-400b-aceb-764788c761c2
* buspirate.c: Turn the "cmd" argument of the various methods into
a "const unsigned char *"; while doing this, declare all arrays being
passed as arguments to be pointers rather than arrays, as the latter
obfuscates the way arrays are being passed to a callee in C.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1196 81a1dc3b-b13d-400b-aceb-764788c761c2
to upload an invalid Intel HEX file
* fileio.c (ihex2b): Turn the "No end of file record found" warning
into an error if no valid record was found at all.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1195 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #38713: Compilation of the documentation breaks with texinfo-5
* doc/avrdude.texi: Turn @itemx into @item, add @headitem to STK600
Routing/Socket card table
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1194 81a1dc3b-b13d-400b-aceb-764788c761c2
buffer address.
* usbasp.c (usbasp_tpi_paged_write): Calculate correct
buffer address; don't issue a SECTION_ERASE command for
each page (a CHIP_ERASE has been done before anyway);
remove the code that attempted to handle partial page
writes, as all writes are now done with a full page.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1191 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk600_xprog_page_erase): Fix argument that is
passed to stk600_xprog_memtype()
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1188 81a1dc3b-b13d-400b-aceb-764788c761c2
elf_getshdrstrndx() as the former one is deprecated
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1187 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrftdi.c, avrftdi_private.h: added additional pin check and bitbanging fallback
* pindefs.[ch]: added a flag to enable/disable output
* ft245r.c: changes because of added flag above
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1184 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7876 JTAGICE mkII fails to connect to attiny if debugwire
is enabled AND target has a very slow clock
* jtagmkII.c (jtagmkII_getsync): When leaving debugWIRE mode
temporarily, immediately retry with ISP, rather than leaving.
* stk500v2 (stk500v2_program_enable): Implemented similar logic
for the JTAGICE3.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1183 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrftdi*.*: changed include check for libftdi/libusb, deactivate 232H if not available
* ft245r.c: changed include check for libftdi/libusb
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1180 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: fixed buff pins of avrftdi programmers (low active buffer need now inverted numbers)
* avrftdi*.*: accept also old libftdi (0.20 still works with it), added powerup to initialize
* ft245r.c: accept libftdi1, code cleanup and make it more similar to avrfdti (os they might be merged someday)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1175 81a1dc3b-b13d-400b-aceb-764788c761c2
avrftdi.c: add pgm->power[up|down] functions and fill
pgm->enable|disable with proper functionality, as suggested by
rliebscher.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1171 81a1dc3b-b13d-400b-aceb-764788c761c2
Use pin_checklist[] of size N_PINS instead N_PINS - 1, to avoid future
problems. Also remove pins_check from set_pin; instead use mask[0] == 0
to check wether to do something or not.
avrftdi_private.h: Change size of pin_checklist[] to N_PINS.
avrftdi.c: Adapt code to new size of pin_checklist. Remove pins_check
from set_pin.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1170 81a1dc3b-b13d-400b-aceb-764788c761c2
otherwise use unsinged long
* ft245r.c: added support for more pin functions led, vcc, buff
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1169 81a1dc3b-b13d-400b-aceb-764788c761c2
Generic function enabling external programming on TPI devices. This
function sets the required guard time (which is passed in as parameter),
checks the TPI identification register, writes SKEY command + SKEY, and
finally polls the NVMEN bit in TPISR.
avr.h: Add prototype definitions of avr_tpi_program_enable() and
avr_tpi_chip_erase().
avrftdi_tpi.c: Removes tpi_skey_cmd array, containing the SKEY command
and the SKEY bytes.
tpi.h: Adds tpi_skey_cmd array, containing the SKEY command and the SKEY
bytes, but in the reverse order of tpi_skey.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1167 81a1dc3b-b13d-400b-aceb-764788c761c2
avrdude.conf.in: Change all programmers' pin definitions to 0-based
avrftdi.c: incorporate new 0-based pindef infrastructure
avrftdi_private.h: Add pin_checklist_t to avrftdi_t for runtime pin
checking in pgm->setpin.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1164 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrpart.[ch]: moved avr_pin_name to pindefs.[ch]
* pgm.c: moved pins_to_str to pindefs.[ch], added initialization of
new pin definitions in pgm_new()
* pindefs.[ch]: added moved functions from other files, added a lot of
documentation, reformatted files using astyle to have consistent spacing,
added a new generic check function for pins
* ft245r.c: used new generic pin check function
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1161 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrftdi.c,buspirate.c,linuxgpio.c,par.c,serbb_*.c: added function call
to fill old pinno entries from new pin definitions.
* pindefs.[hc]: added data struct and helper functions for new pin definitions
* avrdude.conf.in: pins in entries using ftdi_syncbb are now 0-based
* config_gram.y: allow combinations of inverted and non-inverted pins in pin lists
* ft245r.c: reworked to work directly with the new pin definitions,
pins are now 0-based, inverse pins are supported, buff is supported
* pgm.[ch]: added new pin definitions field to programmer structure,
adapted pin display functions
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1160 81a1dc3b-b13d-400b-aceb-764788c761c2
This is not necessary any more, because the "frame" ends in logic 1, so
the pin is high anyway and the MPSSE keeps the pin value as long as it
is idle. Setting the pin low would cause the TPI physical layer in the
AVR part to detect a collision.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1159 81a1dc3b-b13d-400b-aceb-764788c761c2
All I/O of avrftdi_tpi is done in terms of pgm->cmd_tpi() calls instead
of calling avrftdi_tpi_[read,write]_byte() functions directly.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1158 81a1dc3b-b13d-400b-aceb-764788c761c2
Messages are divided by severity and printed accordingly to verbosity, as
specified by the user. The provided severity level are (ERROR, WARN, INFO,
DEBUG, TRACE). Where "ERROR" messages are always printed. Shortcut-macros
including function, from which the output was generated, and line number were
also added. Some log messages were updated and other code warnings removed.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1143 81a1dc3b-b13d-400b-aceb-764788c761c2
Apparently, doing too large read/write I/O on the MPSSE fills up the RX Buffer
of the chip, resulting in STALL/NAK of additional transactions of an OUT request.
Since the OUT request is issued synchronously, an appropriate IN request cannot
be issued, resulting in a deadlock.
This problem is handled by submitting small enough OUT requests, that will not
fill up the RX buffer and interleaving them with IN requests.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1142 81a1dc3b-b13d-400b-aceb-764788c761c2
This includes adding libftdi1 to configure.ac and Makefile.am.
avrftdi code is changed to use libftdi1. At the same time device
discovery is moved to libftdi1. Some error and debug messages in
avrftdi are corrected and/or updated. avrftdi_print is updated,
to print all messages whose verbosity level is less or equal to
the global verbosity level, so that messages with level 0 are always
printed.
This change is tested on OS X 10.6.8, Ubuntu 12.04.2 and Win7 x86_64.
The Win7 version was cross-compiled on OS X 10.6.8.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1141 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: added usbpid, usbvid to usbtiny
* usbtiny.[ch]: use usbpid, usbpid if provided in config file
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1134 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (avrftdi): fix comments about ACBUS vs. ADBUS;
add a comment that the MPSSE signals are fixed by the FTDI
hardware and cannot be changed
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1133 81a1dc3b-b13d-400b-aceb-764788c761c2
joerg_wunsch
springob
rliebscher
hweisbach