in memory type calculation for Xmega "boot" memory region.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1087 81a1dc3b-b13d-400b-aceb-764788c761c2
* main.c: after locating the part information, determine default
memtype for all update options that didn't have a memtype
specified; this is "application" for Xmega parts, and "flash" for
everything else.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1086 81a1dc3b-b13d-400b-aceb-764788c761c2
scanning the program header table, the offsets from a program
header entry must never be used directly when checking the bounds
of the current AVR memory region. Instead, they must always be
checked based on the corresponding section's entry. That way,
Xmega devices now properly take into account whether the segment
fits into any of the application/apptable/boot memory region.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1085 81a1dc3b-b13d-400b-aceb-764788c761c2
read device signature
* main.c: When reading the signature yields 0x000000 or 0xffffff,
retry (up to twice) after some progressive delay.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1084 81a1dc3b-b13d-400b-aceb-764788c761c2
ATxmega128D4): New devices. As Xmega D doesn't feature a fuse0
memory cell, move that one out from the generic .xmega part into
the individual Xmega A parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1083 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_initialize): Insert dummy values for PAGEL and
BS2 if they are not present in the config file, in order to be able
to proceed with the stk500_set_extended_parms() anyway.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1082 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c: For the "flash" pseudo-memory of Xmega devices,
distinguish addresses between "application" and "boot" area.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1081 81a1dc3b-b13d-400b-aceb-764788c761c2
program header segment, subtract `low' from ph[n].p_paddr in order
to correct the magic section offsets for the AVR's non-flash
memory regions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1080 81a1dc3b-b13d-400b-aceb-764788c761c2
any given section maps straight to a program header segment, use a
more sophisticated decision that matches any section as long as it
fits into the segment. This is needed for situations where the
program header segment spans a larger area than the section data
provided. (This can e.g. happen in an ELF file that contains no
data at address 0, like a bootloader only.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1079 81a1dc3b-b13d-400b-aceb-764788c761c2
firmware >= V7.x)
* jtagmkII.c: Add firmware-version dependent handling of Xmega parameters.
V7.x firmware expects the NVM offsets being specified through the Xmega
parameters command, but left out as part of the memory address itself.
* jtagmkII_private.h: Add CMND_SET_XMEGA_PARAMS, and struct xmega_device_desc.
* config_gram.y: Add mcu_base keyword.
* avrpart.h: (Dito.)
* lexer.l: (Dito.)
* avrdude.conf.in (.xmega): add mcu_base, and data memory segment.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1078 81a1dc3b-b13d-400b-aceb-764788c761c2
firmware < V7.x)
* jtagmkII.c: When going to write to the boot section of flash,
use MTYPE_BOOT_FLASH rather than MTYPE_FLASH
* jtagmkII_private.h: add MTYPE_BOOT_FLASH constant
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1077 81a1dc3b-b13d-400b-aceb-764788c761c2
supported error
* stk500v2.c: Handle all Xmega memory sections (except
"prodsig" which is not documented in AVR079)
* fileio.c: Treat the "boot", "application", and "apptable"
regions (which are actually subregions of "flash") all as
being flash, i.e. suppress trailing 0xFF bytes when reading
them
* avr.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1075 81a1dc3b-b13d-400b-aceb-764788c761c2
"GO" code in again, but only activate it when programming an
Xmega device through PDI.
Wonderfully consistent tools.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1071 81a1dc3b-b13d-400b-aceb-764788c761c2
turned out to do more harm than good; on the Xmega, it caused exactly
the opposite reaction, the CPU stopped. Even without it, after the
RESET command, the target is running already. So, drop the GO.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1070 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrftdi.[ch]: moved global data into private data structure, moved
private defines from header file into source file
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1068 81a1dc3b-b13d-400b-aceb-764788c761c2
(generating the programmers lists)
* doc/avrdude.texi: Add include of generated table of programmers
* doc/Makefile.am: Add generating of table of programmers in programmers.texi
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1062 81a1dc3b-b13d-400b-aceb-764788c761c2
* ft245r.[ch]: new programmer type implementation
* configure.ac: add pthread as link library
* avrdude.conf.in: added some new programmers
* Makefile.am: added new source files to compile
* pindefs.h: change PIN_MASK, PIN_INVERSE to highest bit of unsigned int
* pgm.[ch]: added generic function to print pin assignments (taken from par.c)
* par.c: moved pin assigment print function to pgm.c
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1055 81a1dc3b-b13d-400b-aceb-764788c761c2
* config.[hc]: removed unused function id(), use value.type to select
values
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1053 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7686 Updating buspirate ascii mode to current firmware, use AUX
as clock generator, and setting of serial receive timeout
* buspirate.c: added paged_write, changed binary mode setup/detection,
added clock output on AUX pin
* avrdude.1: updated documentation
* doc/avrdude.texi: updated documentation
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1052 81a1dc3b-b13d-400b-aceb-764788c761c2
will update only the table in pgm_type.c.
* config_gram.y, lexer.l: removed programmer type keywords,
use now locate_programmer_type() function
* pgm_type.[ch]: added new files for table of programmer types
* main.c: allow list of programmer types by -c ?type
* avrdude.conf.in: changed all type keywords to quoted strings
* doc/avrdude.texi: changed description of type definition, list
of valid types is now included from generated file
* doc/Makefile.am: generate list of programmer types for doc
* all programmers [hc]: add xxx_desc string for description of programmer
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1051 81a1dc3b-b13d-400b-aceb-764788c761c2
nounput. This gets rid of a compiler warning, so we are warning-free
again.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1048 81a1dc3b-b13d-400b-aceb-764788c761c2
abstract .xmega part as parent for xmegas
* main.c: hide parts starting with '.' from parts list
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1046 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: updated documentation comment and some programmers
have now parents
* config_gram.y: initpgm will now called at first use of programmer
in main. parser sets only the function pointer in the pgm structure.
Pin and pin lists definitions can now be empty to remove the parents
setting.
* doc/avrdude.texi: updated documentation
* main.c: added call to pgm->initpgm after locate_programmer
* pgm.[hc]: added field initpgm in structure, added function pgm_dup
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1045 81a1dc3b-b13d-400b-aceb-764788c761c2
to lusb0_usb.h (for whatever reason). Autoprobe for the filename
during configure, and include whatever is appropriate.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1043 81a1dc3b-b13d-400b-aceb-764788c761c2
functions. So a negative return code led never to a fallback to byte
functions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1042 81a1dc3b-b13d-400b-aceb-764788c761c2
* config_gram.y: if memory section is overwritten old entry is removed
(not in original patch)
* config_gram.y: if programmer or part is defined twice, a warning is
output and the first instance is removed
General cleanup and free functions, so valgrind does not report any lost
blocks at program end.
* avrpart.[hc]: added avr_free_(opcode|mem|part) functions
* pgm.[hc]: added pgm_free function
* update.[hc]: added free_update functions
* config.[hc]: added cleanup_config function, use yylex_destroy to reset
the lexer after usage. (So it can be reused.)
* main.c: add cleanup_main function which is called by atexit() (This
frees all lists so that at program exit only really lost memory is
reported by valgrind.)
* usbasp.c: added libusb_free_device_list() and libusb_exit() calls to
avoid lost memory
* buspirate.c: moved memory allocation from initpgm to setup and added
free in teardown
* configure.ac: add definition of HAVE_YYLEX_DESTROY if $LEX is flex.
* Makefile.am: added . in front of SUBDIRS to build avrdude before trying
to use it for creating the part list for the docs.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1041 81a1dc3b-b13d-400b-aceb-764788c761c2
id "usbasp" nibobee and old usbasp are tried as they were currently
implemented within usbasp
* avrdude.conf.in: added usb params to "usbasp", added new entry "nibobee"
with params which were hardcoded in usbasp.c, and added an entry
"usbasb-clone" which only checks vid/pid.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@1040 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch
Rene Liebscher