* jtag3.c (jtag3_edbg_recv_frame): Return correct length as
reported in the response packet, rather than full 512 byte which
are always reported by the CMSIS-DAP layer. Miscalculations
based on the wrongly reported length caused heap corruption
elsewhere, so this is presumably also a fix for bug #43078.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1344 81a1dc3b-b13d-400b-aceb-764788c761c2
flash page
* usbasp.c (usbasp_spi_paged_write): Remove USBASP_BLOCKFLAG_LAST.
It is no longer needed, as we always write full pages now in paged
write mode.
This prevents each flash page from being written twice, where the
second attempt on older devices (ATmega64/128) signalled an immediate
"ready" condition when polling (likely a silicon bug) even though they
were still in progress. This caused the USBasp firmware to proceed,
and fill the page buffer anew which eventually caused the data
corruption.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1343 81a1dc3b-b13d-400b-aceb-764788c761c2
after changing lock byte
* stk500v2.c (stk500isp_write_byte): As a workaround for broken
tool firmware, add 10 ms of delay before returning from any
single-byte write operation.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1337 81a1dc3b-b13d-400b-aceb-764788c761c2
every byte-wide access (rather than JTAGICE3 only). This finally
obsoletes the use of the prehistoric SPI_MULTI command where
AVRDUDE used to assemble all the low-level ISP stuff by itself.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1336 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (m168, m328, m48, m88, t1634, t26, t261, t461,
t861, t88): In efuse (or hfuse for t26) read operation, turn all
bits in byte 3 from "x" to "o" (output); this is a first step
towards fixing the symptoms mentioned in the bug, by unifying the
behaviour between different AVRs. Not touched are the historic
devices where the fuses are not documented to form a full byte
each (2333, 4433, 4434, 8535, m103, m161, m163).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1335 81a1dc3b-b13d-400b-aceb-764788c761c2
* usb_libusb.c (usbdev_close): Only issue the usb_reset() for
Linux systems, as these are the only ones that seem to require
it under some circumstances.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1273 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7896: DFU FLIPv2 programming support
* pgm_type.c: Add the flip2 programmer type.
* config_gram.y: Allow for the usbid keyword in a device definition.
* avrdude.conf.in: Add usbpid values to those Xmega devices where
applicable.
* avrpart.h: Add usbpid device field.
* dfu.c: (New file.)
* dfu.h: (New file.)
* flip.c: (New file.)
* flip.h: (New file.)
* Makefile.am: Add new files.
* doc/avrdude.texi: Document the changes.
* avrdude.1: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1258 81a1dc3b-b13d-400b-aceb-764788c761c2
* fileio.c (fileio): open file in binary mode also for FMT_ELF
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1253 81a1dc3b-b13d-400b-aceb-764788c761c2
* main.c: Always clear the UF_AUTO_ERASE flag if either a
non-Xmega device was found, or the programmer does not offer a
page_erase method.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1242 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #40040: Support for ATtiny20 and ATtiny40
* avrdude.conf.in: Restructure the reduced-core tiny devices
to use a common entry .reduced_core_tiny; add ATtiny20 and
ATtiny40
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1236 81a1dc3b-b13d-400b-aceb-764788c761c2
previous version) features on top so they will become immediately apparent
in the release notes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1233 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #40033: Support for the XMegaE5 family
* avrdude.conf.in (ATxmega8E6, ATxmega16E5, ATxmega32E5): New
entries.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1231 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7710: usb_libusb: Check VID/PID before opening device
* usb_libusb.c (usbdev_open): Swap the sequence of verifying the
VID:PID, and opening the device.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1228 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7657 Add ATmega406 support for avrdude using DRAGON + JTAG
* avrdude.conf.in (ATmega406): New entry.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1225 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_getsync): Loop 10 times trying to get in
sync with the programmer.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1223 81a1dc3b-b13d-400b-aceb-764788c761c2
* avr.c (avr_read, avr_write): Change the progress reporting for
paged read/write from per-address to per-considered-page. This
ought to give a realistic estimation about the time still to be
spent.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1220 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf: Bump the chip_erase_delay for all ATmega*4 devices
to 55 ms. While the datasheet still claims 9 ms, all the XML files
tell either 45 or 55 ms, depending on STK600 or not.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1217 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #38951: AVR109 use byte offset instead of word offset
patch #8045: AVR109 butterfly failing
* butterfly.c (butterfly_paged_load, butterfly_paged_write):
fix calculation of 'A' address when operating on flash memory.
It must be given in terms of 16-bit words rather than bytes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1205 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtag3.c (jtag3_initialize): initialize the eeprom_pagesize
private attribute so the page cache will actually be usable
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1202 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtag3.c (jtag3_read_byte, jtag3_write_byte): Correctly apply the
relevant part of mem->offset as the address to operate on.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1201 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #35800: Compilation error on certain systems if parport is disabled
* linux_ppdev.h: Conditionalize inclusion of <linux/parport.h> and
<linux/ppdev.h> on HAVE_PARPORT
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1198 81a1dc3b-b13d-400b-aceb-764788c761c2
* buspirate.c: Turn the "cmd" argument of the various methods into
a "const unsigned char *"; while doing this, declare all arrays being
passed as arguments to be pointers rather than arrays, as the latter
obfuscates the way arrays are being passed to a callee in C.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1196 81a1dc3b-b13d-400b-aceb-764788c761c2
to upload an invalid Intel HEX file
* fileio.c (ihex2b): Turn the "No end of file record found" warning
into an error if no valid record was found at all.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1195 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #38713: Compilation of the documentation breaks with texinfo-5
* doc/avrdude.texi: Turn @itemx into @item, add @headitem to STK600
Routing/Socket card table
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1194 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk600_xprog_page_erase): Fix argument that is
passed to stk600_xprog_memtype()
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1188 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7876 JTAGICE mkII fails to connect to attiny if debugwire
is enabled AND target has a very slow clock
* jtagmkII.c (jtagmkII_getsync): When leaving debugWIRE mode
temporarily, immediately retry with ISP, rather than leaving.
* stk500v2 (stk500v2_program_enable): Implemented similar logic
for the JTAGICE3.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1183 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtagmkII.c (jtagmkII_initialize): For Xmega devices, and
firmware >= 7.x, don't trigger a RESET, in order to work around a
firmware bug that appears to be present in at least firmware 7.24
for the Dragon.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1125 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Add "jtag3isp" programmer
* jtag3.c: jtag3_setparm() is now public
* jtag3.h: (Dito)
* stk500v2_private.h: Command 0x1D is CMD_SPI_MULTI only
for STK500v2, AVRISPmkII, and JTAGICEmkII; for JTAGICE3,
it's CMD_SET_SCK now; also add CMD_GET_SCK
* avrpart.c (avr_get_output_index): New function
* avrpart.h: (Dito)
* stk500v2.c: Implement the pasthrough programmer glue logic
for JTAGICE3 in ISP mode
* stk500v2.h: (Dito)
* avrdude.1: Document the JTAGICE3 support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1119 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Fix page sizes for all Xmega devices,
by cross-checking against Atmel Studio's device XML files
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1112 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI and JTAG).
* jtagmkII.c (jtagmkII_set_xmega_params): Use "fuse1" rather
than "fuse0" memory space to fill in the NVM offset from, as
there is no "fuse0" on some Xmega devices.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1111 81a1dc3b-b13d-400b-aceb-764788c761c2
traces made by Knut Schwichtenberg, and by similarity to
JTAGICEmkII.
Still quite incomplete, just megaAVR/JTAG is done by now.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1109 81a1dc3b-b13d-400b-aceb-764788c761c2
* main.c: after locating the part information, determine default
memtype for all update options that didn't have a memtype
specified; this is "application" for Xmega parts, and "flash" for
everything else.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1086 81a1dc3b-b13d-400b-aceb-764788c761c2
read device signature
* main.c: When reading the signature yields 0x000000 or 0xffffff,
retry (up to twice) after some progressive delay.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1084 81a1dc3b-b13d-400b-aceb-764788c761c2
ATxmega128D4): New devices. As Xmega D doesn't feature a fuse0
memory cell, move that one out from the generic .xmega part into
the individual Xmega A parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1083 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_initialize): Insert dummy values for PAGEL and
BS2 if they are not present in the config file, in order to be able
to proceed with the stk500_set_extended_parms() anyway.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1082 81a1dc3b-b13d-400b-aceb-764788c761c2
firmware >= V7.x)
* jtagmkII.c: Add firmware-version dependent handling of Xmega parameters.
V7.x firmware expects the NVM offsets being specified through the Xmega
parameters command, but left out as part of the memory address itself.
* jtagmkII_private.h: Add CMND_SET_XMEGA_PARAMS, and struct xmega_device_desc.
* config_gram.y: Add mcu_base keyword.
* avrpart.h: (Dito.)
* lexer.l: (Dito.)
* avrdude.conf.in (.xmega): add mcu_base, and data memory segment.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1078 81a1dc3b-b13d-400b-aceb-764788c761c2
supported error
* stk500v2.c: Handle all Xmega memory sections (except
"prodsig" which is not documented in AVR079)
* fileio.c: Treat the "boot", "application", and "apptable"
regions (which are actually subregions of "flash") all as
being flash, i.e. suppress trailing 0xFF bytes when reading
them
* avr.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1075 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7056: adding support for mikrokopter bootloader to butterfly
* butterfly.c: Add some specific logic to handle the
mikrokopter.de butterfly bootloader.
* butterfly.h: Add one related function declaration.
* config_gram.y: Add butterfly_mk keyword.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add entry for butterfly_mk.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@991 81a1dc3b-b13d-400b-aceb-764788c761c2
Wolfgang Moser, Ville Voipio, Hannes Weisbach
patch #7486: Patch to add FT2232C/D, FT2232H, FT4232H,
usbvid, usbpid, usbdev for USB support - Based on #7062
* avrftdi.c: New file.
* avrftdi.h: (Ditto.)
* configure.ac: Add check for libftdi.
* config_gram.y: Add AVRFTDI and per-programmer USB string
keywords.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add avrftdi and 2232HIO programmers.
* pgm.h: Add USB parameters.
* Makefile.am: Add avrftdi.c and avrftdi.h.
* AUTHORS: Mention the new authors.
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@979 81a1dc3b-b13d-400b-aceb-764788c761c2
* configure.ac: For Win32 environments, add a check whether the
compiler understands the -mno-cygwin option. If not, don't use
it but suggest using a different compiler.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@930 81a1dc3b-b13d-400b-aceb-764788c761c2
Add ATtiny4/5/9/10 to avrdude.conf.in.
Document TPI and new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@916 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch
Hannes Weisbach
Rene Liebscher
Nils Springob
David Hoerl