the old AVR910 device codes; we've got signature verification
now so better rely on that.
* avr910.c: Revert the signature bytes returned, as it already
happened in butterfly.c. This closes bug #14998: Signature Bytes
read in wrong order (avr910 mode)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@638 81a1dc3b-b13d-400b-aceb-764788c761c2
avr910 programmer.
Original Submission: The attached patch against avrdude 4.4.0 fixes
the following problems with paged writes in avr910.c:
- failure to re-set address after page writes;
- no polling or delay after page writes;
- no page writes when not using auto-increment;
- an extraneous page write when data ends on page boundary.
Submitted by: "Nic" <avrdude@schraudolph.org>
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@510 81a1dc3b-b13d-400b-aceb-764788c761c2
when passing unsigned char * when char * is in the prototype and vice
versa. Clean these up along with a few others.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@491 81a1dc3b-b13d-400b-aceb-764788c761c2
yesterday's changes (i.e. before rev. 1.10 of ser_posix.c), that is,
exit(1) in case of a timeout. Previously, the upper layers didn't see
the timeout at all.
Quite possible that some of these drivers could handle a timeout more
intelligently though. At least for the rather sophisticated STK500v2
protocol, I think it should be possible to retry the request.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@460 81a1dc3b-b13d-400b-aceb-764788c761c2
* pgm.c: Fixed wrong type for default_open introduced by the cleanup yesterday.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@409 81a1dc3b-b13d-400b-aceb-764788c761c2
Move save/restore-functionality into open/close.
* par.c: open/close now saves/restores PPICTRL, too.
* TODO: exitspecs don't work if RESET is in PPICTRL.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@407 81a1dc3b-b13d-400b-aceb-764788c761c2
bytes since the 'R' command returns MSB first and the internal buffer
stores LSB first.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@307 81a1dc3b-b13d-400b-aceb-764788c761c2
removed in my previous patch. Terminal mode read/writes are broken
without those methods. D'oh!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@305 81a1dc3b-b13d-400b-aceb-764788c761c2
incr supported by programmer hw, don't send addr for every byte.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@304 81a1dc3b-b13d-400b-aceb-764788c761c2
available.
* avr910.c (avr910_vfy_cmd_sent): New function.
(avr910_chip_erase): Add support for chip erase.
(avr910_enter_prog_mode): New function.
(avr910_leave_prog_mode): New function.
(avr910_initialize): Add code to select device type and enter prog mode.
(avr910_close): Leave programming mode before closing serial port.
(avr910_read_sig_bytes): New function.
(avr910_initpgm): Add avr910_read_sig_bytes method to pgm initializer.
* avrdude.conf.in: Add note about deprecating devicecode.
Change all occurences of devicecode to stk500_devcode.
Add avr910_devcode to a few parts for testing.
* avrpart.h (struct avrpart): Change devicecode field to stk500_devcode.
(struct avrpart): Add avr910_devcode field.
* config_gram.y: Add K_STK500_DEVCODE and K_AVR910_DEVCODE tokens.
Generate an error if devicecode is found in the config file.
Handle parsing of avr910_devcode and stk500_devcode.
* lexer.l: Handle parsing of avr910_devcode and stk500_devcode.
* pgm.c: Initialize pgm->read_sig_bytes field.
* pgm.h: Add pgm->read_sig_bytes field.
* stk500.c: Use stk500_devcode instead of devicecode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@293 81a1dc3b-b13d-400b-aceb-764788c761c2
* config_gram.y: Add parsing of avr910 programmer.
* lexer.l: Add avr910 token.
* avr910.c: [this is still work in progress]
Add some debug output.
Add probe for programmer presense.
* main.c: Set port to default_serial if programmer type is avr910.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@292 81a1dc3b-b13d-400b-aceb-764788c761c2
ser_posix.c files.
* avr910.c: New file (stubs for avr910 serial programmer).
* avr910.h: New file.
* ser_posix.c: New file.
* ser_win32.c: New file (just stubs for now).
* serial.h: New file.
* stk500.c: Move all the code for accessing the posix serial ports
into ser_posix. This will make a native win32 port easier and allows
the avr910 programmer to share the serial code.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@289 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch
Brian S. Dean
kiwi64ajs
Jan-Hinnerk Reichert
Theodore A. Roth
Eric Weddington