ATxmega128D4): New devices. As Xmega D doesn't feature a fuse0
memory cell, move that one out from the generic .xmega part into
the individual Xmega A parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1083 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_initialize): Insert dummy values for PAGEL and
BS2 if they are not present in the config file, in order to be able
to proceed with the stk500_set_extended_parms() anyway.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1082 81a1dc3b-b13d-400b-aceb-764788c761c2
firmware >= V7.x)
* jtagmkII.c: Add firmware-version dependent handling of Xmega parameters.
V7.x firmware expects the NVM offsets being specified through the Xmega
parameters command, but left out as part of the memory address itself.
* jtagmkII_private.h: Add CMND_SET_XMEGA_PARAMS, and struct xmega_device_desc.
* config_gram.y: Add mcu_base keyword.
* avrpart.h: (Dito.)
* lexer.l: (Dito.)
* avrdude.conf.in (.xmega): add mcu_base, and data memory segment.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1078 81a1dc3b-b13d-400b-aceb-764788c761c2
supported error
* stk500v2.c: Handle all Xmega memory sections (except
"prodsig" which is not documented in AVR079)
* fileio.c: Treat the "boot", "application", and "apptable"
regions (which are actually subregions of "flash") all as
being flash, i.e. suppress trailing 0xFF bytes when reading
them
* avr.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1075 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7056: adding support for mikrokopter bootloader to butterfly
* butterfly.c: Add some specific logic to handle the
mikrokopter.de butterfly bootloader.
* butterfly.h: Add one related function declaration.
* config_gram.y: Add butterfly_mk keyword.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add entry for butterfly_mk.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@991 81a1dc3b-b13d-400b-aceb-764788c761c2
Wolfgang Moser, Ville Voipio, Hannes Weisbach
patch #7486: Patch to add FT2232C/D, FT2232H, FT4232H,
usbvid, usbpid, usbdev for USB support - Based on #7062
* avrftdi.c: New file.
* avrftdi.h: (Ditto.)
* configure.ac: Add check for libftdi.
* config_gram.y: Add AVRFTDI and per-programmer USB string
keywords.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add avrftdi and 2232HIO programmers.
* pgm.h: Add USB parameters.
* Makefile.am: Add avrftdi.c and avrftdi.h.
* AUTHORS: Mention the new authors.
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@979 81a1dc3b-b13d-400b-aceb-764788c761c2
* configure.ac: For Win32 environments, add a check whether the
compiler understands the -mno-cygwin option. If not, don't use
it but suggest using a different compiler.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@930 81a1dc3b-b13d-400b-aceb-764788c761c2
Add ATtiny4/5/9/10 to avrdude.conf.in.
Document TPI and new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@916 81a1dc3b-b13d-400b-aceb-764788c761c2
conditional compilation of usb_reset() introduced in r798.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@841 81a1dc3b-b13d-400b-aceb-764788c761c2
support it
Do not call pgm->perform_osccal() unless it is != 0.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@822 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (ATxmega256A3): new device.
* stk500v2 (stk500v2_initialize): Enable the AVRISPmkII as a
PDI-capable device for ATxmega parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@809 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #24749: add support for '328p
* avrdude.conf.in (ATmega328P): new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@796 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6261: avrdude won't use dragon/debugwire to write a file
to eeprom
* jtagmkII.c (jtagmkII_paged_write): when in debugWire mode,
implement a paged write to EEPROM as a series of byte writes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@792 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6542: paged_load fails on the MIB510 programming board
* stk500.c: Add a workaround for the different signon sequence on
MIB510 programmers.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@791 81a1dc3b-b13d-400b-aceb-764788c761c2
for Xmega programming using the JTAG ICE mkII in JTAG mode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@780 81a1dc3b-b13d-400b-aceb-764788c761c2
allow to continue with -F if it failed yet do not attempt to
perform anything on the device itself. That way, -tF could be
specified for programmers like the STK500/STK600 even without a
device connected, just in order to allow changing parameters on
the programmer itself.
* avrdude.1: Document that possible use of the -F option.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@779 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI mode of the STK600 is supported. Single-byte EEPROM
(and flash) updates do not work yet.
* avr.c: "boot" memory is a candidate memory region for paged
operations, besides "flash" and "eeprom".
* avrdude.conf.in: add ATxmega128A1 and ATxmega128A1revD
* avrpart.h: add the AVRPART_HAS_PDI flag (used to distinguish
ATxmega parts from classic AVRs), the nvm_base part field, and
the offset field for a memory region.
* config_gram.y: add "has_pdi", "nvm_base", and "offset"
* lexer.l: (Ditto.)
* main.c: disable auto_erase for ATxmega parts
* stk500v2.c: implement the XPROG functionality, and divert to
this for ATxmega parts
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@777 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch
Rene Liebscher
Nils Springob
David Hoerl
Michal Ludvig