Each memory image byte is now tagged as it's being read from a file.
Only bytes read from a file will be written or verified (modulo page
granularity requirements).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1007 81a1dc3b-b13d-400b-aceb-764788c761c2
programmers)
* config_gram.y: Introduce new keyword "is_at90s1200".
* lexer.l: (Ditto.)
* avrdude.conf.in: Applew new keyword to the AT90S1200 device.
* avrpart.h: Introduce new flag AVRPART_IS_AT90S1200, reflecting
the is_at90s1200 configuration keyword.
* bitbang.c (bitbang_initialize): Replace existing test for
AT90S1200 by AVRPART_IS_AT90S1200
* avr.c (avr_write_byte_default): Avoid the pre-write reading for
the AT90S1200, as this appears to sometimes corrupt the high byte
by pre-programming the low byte just written into it.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1002 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Correctly declare EEPROM page sizes for
all Xmega devices (0x20 instead of 0x100).
* avr.c: If a memory region has a page size declared, try
using the paged IO routines regardless of the target memory
name. Xmega EEPROM requires to be written in paged mode.
Correctly use a long (rather than unsigned long) variable to
evaluate the success status of the paged mode write attempt.
* stk500v2.c: Don't apply TIF space offsets twice (bug #27995:
AVRDUDE 5.8svn fails to program and read XMEGA); use
stk500v2_loadaddr() prior to paged mode (EEPROM and flash) writes,
otherwise programming of flash areas will fail; while being there,
check the return value of stk500v2_loadaddr() everywhere; use the
correct write/erase mode bits (same as AVR Studio does).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@907 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI mode of the STK600 is supported. Single-byte EEPROM
(and flash) updates do not work yet.
* avr.c: "boot" memory is a candidate memory region for paged
operations, besides "flash" and "eeprom".
* avrdude.conf.in: add ATxmega128A1 and ATxmega128A1revD
* avrpart.h: add the AVRPART_HAS_PDI flag (used to distinguish
ATxmega parts from classic AVRs), the nvm_base part field, and
the offset field for a memory region.
* config_gram.y: add "has_pdi", "nvm_base", and "offset"
* lexer.l: (Ditto.)
* main.c: disable auto_erase for ATxmega parts
* stk500v2.c: implement the XPROG functionality, and divert to
this for ATxmega parts
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@777 81a1dc3b-b13d-400b-aceb-764788c761c2
paged_write backend functions iff the memory area in question has
a page_size != 0.
This is supposed to fix bug #19234: avrdude-5.3.1 segfaults when
stk500v1 tries to program an ATtiny15
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@739 81a1dc3b-b13d-400b-aceb-764788c761c2
- Make all internal functions "static".
- Make sure each module's header and implementation file match.
- Remove all library-like functionality from main.c, so only
the actual frontend remains in main.c.
- Add C++ brackets to all header files.
That effectively leaves the various module C files as something like
an "avrdude library", with main.c being the currently only frontend
program for that library. In theory, it should be possible to write
different frontends using the same library backend functions though.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@722 81a1dc3b-b13d-400b-aceb-764788c761c2
declarations in each file by a central header file "avrdude.h".
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@721 81a1dc3b-b13d-400b-aceb-764788c761c2
avr_write(), respectively, in case the paged_load()/paged_write()
methods succeeded, rather than only 0.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@696 81a1dc3b-b13d-400b-aceb-764788c761c2
fallback from each programmer's paged_load() or paged_write()
method, respectively. The return value needs to be checked for
being greater or equal than 0 rather equal to 0 in order to
assume the operation has been successful.
Fixes bug #18489: avrdude is too slow (20 byte/s)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@695 81a1dc3b-b13d-400b-aceb-764788c761c2
avr_read_byte_default() and avr_write_byte_default (resp.) by directly
calling the latter functions from within all programmers that don't
implement their own read_byte()/write_byte() methods. In turn, make the
read_byte() and write_byte() methods mandatory, and the cmd() method
(direct ISP command) optional instead (it's effectively mandatory for
any programmer using avr_read_byte_default()/avr_write_byte_default()
though). Remove all the pointless cmd() method stubs from those programmers
that don't need it.
Eliminate avr_read_byte() as it was now completely identical to
pgm->read_byte().
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@684 81a1dc3b-b13d-400b-aceb-764788c761c2
definitions that are organized in pages.
* avr.c (avr_write_byte_default): Consider using the loadpage
instructions only if the respective memory is marked "paged".
Closes bug #17199: EEPROM fails verification on ATmega645 with
pony-stk200 hardware
Closes bug #16849: EEPROM write fails for AT90USB1287 with mode 0x41
Closes bug #15146: stk500v2_paged_write: loadpage instruction not
defined for part
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@622 81a1dc3b-b13d-400b-aceb-764788c761c2
jtag2 and bitbang programmers are working, stk500v2
still needs to be done.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@581 81a1dc3b-b13d-400b-aceb-764788c761c2
* add support for parts with just 'fuse' memory
* if any fuse memories are altered, reflect those changes in the
post-programming safemode check so that safemode no longer
complains about fuses which were intentionally altered; this
eliminates the need to completely disable safemode using -u in
order to program fuses.
* provide -s option which will not ask to restore fuses, it will
just do it
Submitted by: Colin O'Flynn <coflynn@newae.com>
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@519 81a1dc3b-b13d-400b-aceb-764788c761c2
*avr.h: Removed prototypes for moved functions
*avrpart.h: Added prototypes for functions in avrpart.c
*Makefile.am: Added new file avrpart.c
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@388 81a1dc3b-b13d-400b-aceb-764788c761c2
resides above the last non-0xff data value in the address space. Only
do this for flash memory since writing a 0xff to flash is a no-op.
This has the affect of creating smaller output files when dumping
memory contents from flash if the program in flash does not consume
the whole memory space. It also results in shorter programming times
when avrdude is asked to load a file into flash that has lots of 0xff
filled data past the last non-0xff data value.
I think this is basically where Alexey was going with his s-record
routine, but this should have a similar affect for all the I/O
routines. The main difference is that Alexey's also optimized 0xff
from the beginning of the address space and was not limited to flash.
I think that these optimizations should be limited to the flash since
it is currently the only memory that treats 0xff as special.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@331 81a1dc3b-b13d-400b-aceb-764788c761c2
Have avr_read_byte() call pgm->read_byte() or avr_read_byte_default().
Add avr_write_byte_default().
Have avr_write_byte() call pgm->write_byte or avr_write_byte_default().
* pgm.c: Initialize pgm->write_byte and pgm->read_byte.
* pgm.h: Add write_byte and read_byte fields to struct programmer_t.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@296 81a1dc3b-b13d-400b-aceb-764788c761c2
available.
* avr910.c (avr910_vfy_cmd_sent): New function.
(avr910_chip_erase): Add support for chip erase.
(avr910_enter_prog_mode): New function.
(avr910_leave_prog_mode): New function.
(avr910_initialize): Add code to select device type and enter prog mode.
(avr910_close): Leave programming mode before closing serial port.
(avr910_read_sig_bytes): New function.
(avr910_initpgm): Add avr910_read_sig_bytes method to pgm initializer.
* avrdude.conf.in: Add note about deprecating devicecode.
Change all occurences of devicecode to stk500_devcode.
Add avr910_devcode to a few parts for testing.
* avrpart.h (struct avrpart): Change devicecode field to stk500_devcode.
(struct avrpart): Add avr910_devcode field.
* config_gram.y: Add K_STK500_DEVCODE and K_AVR910_DEVCODE tokens.
Generate an error if devicecode is found in the config file.
Handle parsing of avr910_devcode and stk500_devcode.
* lexer.l: Handle parsing of avr910_devcode and stk500_devcode.
* pgm.c: Initialize pgm->read_sig_bytes field.
* pgm.h: Add pgm->read_sig_bytes field.
* stk500.c: Use stk500_devcode instead of devicecode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@293 81a1dc3b-b13d-400b-aceb-764788c761c2
all on non-paged-memory parts. The problem was that the page size was
defaulting to 256 (maximum for the stk500), but the timeout for a
response from the stk500 before declaring it dead was only 0.5
seconds. But it takes much longer than 0.5 seconds to program 256
bytes, so we just weren't waiting long enough.
Fix this in two ways - increase the timeout to 5 seconds, and decrease
the page size to 16 bytes for non-paged parts. The programming time
for 16 bytes is short enough to provide the user with some feedback
that something is happening.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@260 81a1dc3b-b13d-400b-aceb-764788c761c2
itself is paged as it doesn't appear to work otherwise.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@259 81a1dc3b-b13d-400b-aceb-764788c761c2
$HOME/.avrduderc. Entries from .avrduderc take precedence over those
from the system wide config file in ${PREFIX}/etc/avrdude.conf.
Track and display the config file name and line number when we print
out the available parts and programmers. This is useful in case
someone has overridden a definition in their .avrduderc file and is
wondering why the definition in the system wide config file is not
being used.
Remove the default programmer 'stk500' from the distributed config
file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@222 81a1dc3b-b13d-400b-aceb-764788c761c2
programming mode. Use 'retry_pulse' in the per-part specification
that can currently take values of 'reset' or 'sck', the default being
'sck' which preserves the previous behaviour. Some newer parts
indicate that /RESET should be pulsed, while older parts say to pulse
SCK.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@212 81a1dc3b-b13d-400b-aceb-764788c761c2
say whether parts support these programming modes or not. Possible
values for 'serial' are 'yes' or 'no'. Possible values for 'parallel'
are 'yes', 'no', or 'pseudo'. Add a bit mask of flags to the AVRPART
structure to capture these settings. Use these within
stk500_initialize() to set the device parameters correctly.
Defaults for 'serial' and 'parallel' are 'yes' unless specified
otherwise.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@208 81a1dc3b-b13d-400b-aceb-764788c761c2
PAGEL and BS2 signals and the disposition of the reset pin
('dedicated' or 'io').
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@202 81a1dc3b-b13d-400b-aceb-764788c761c2
* .cvsignore: Ignore autoconf files.
* AUTHORS: New file.
* ChangeLog: New file.
* Makefile: Removed file.
* Makefile.am: New file.
* NEWS: New file.
* README: New file.
* bootstrap: New file.
* configure.ac: New file.
* avr.c: Include ac_cfg.h (generated by autoconf).
* config.c: Include ac_cfg.h.
Include config_gram.h instead of y.tab.h.
* config.h: If HAS_YYSTYPE is not defined, define YYSTYPE.
* config_gram.y: Include ac_cfg.h.
* fileio.c: Include ac_cfg.h.
* lexer.l: Include config_gram.h instead of y.tab.h.
* lists.c: Include ac_cfg.h.
* main.c: Include ac_cfg.h.
* par.c: Include ac_cfg.h.
* pgm.c: Include ac_cfg.h.
* ppi.c: Include ac_cfg.h.
* stk500.c: Include ac_cfg.h.
* term.c: Include ac_cfg.h.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@192 81a1dc3b-b13d-400b-aceb-764788c761c2
This was intended to be used for identifying code in the field for
incoming bug reports, but I've never really found it all that useful.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@171 81a1dc3b-b13d-400b-aceb-764788c761c2
This change represents a name change only. There is currently an
effort to port AVRPROG to other platforms including Linux and Windows.
Since Atmel's programmer binary that's included within their AVR
Studio software is named AVRPROG.EXE on the Windows OS, there is the
chance for confusion if we keep calling this program AVRPROG as well.
Up until now the name hasn't really been a problem since there was no
chance to confuse 'avrprog' on Unix with Atmel's AVRPROG because
Atmel's tools only run on Windows. But with the Unix 'avrprog'
possibly being ported to Windows, I felt a name change was the best
way to avoid problems.
So - from this point forward, my FreeBSD Unix program formerly known
as AVRPROG will subsequently be known as AVRDUDE (AVR Downloader/UploaDEr).
This change also represents a time when the AVRDUDE sources move from
my own private repository to a public repository. This will give
other developers a chance to port AVRDUDE to other platforms and
extend its functionality to support additional programming hardware,
etc.
So goodbye AVRPROG, welcome AVRDUDE!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@170 81a1dc3b-b13d-400b-aceb-764788c761c2
"non-paged" parts. Take advantage of that and use the faster internal
routines of the STK500 for those parts as well.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@162 81a1dc3b-b13d-400b-aceb-764788c761c2
supports paged reads and writes. This greatly decreases the
program/verify time from about 4.5 minutes down to about 10 seconds in
a 12K program size test case.
Print out the hardware and firmware version for the STK500 if verbose
is enabled.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@161 81a1dc3b-b13d-400b-aceb-764788c761c2
that programmers other than the direct parallel port connection can be
supported.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@159 81a1dc3b-b13d-400b-aceb-764788c761c2
appeared in version 2.1.0, but was changed to a 4 byte counter in
version 2.1.1. Reminded by Joerg Wunsch.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@150 81a1dc3b-b13d-400b-aceb-764788c761c2
cycle count stored at the end of EEPROM. It seems as though Atmel was
greatly conservative in claiming a 1000 count reliability for the
FLASH. I current have a part that has been reprogrammed 173330 times,
and counting.
Fix a compiler warning.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@144 81a1dc3b-b13d-400b-aceb-764788c761c2
that it is tracked no matter where the erase was initiated: command
line mode or interactive mode, without code duplicaiton.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@141 81a1dc3b-b13d-400b-aceb-764788c761c2
undergone. This utilizes the last two bytes of EEPROM to maintain a
counter that is incremented each time the part is erased.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@138 81a1dc3b-b13d-400b-aceb-764788c761c2
Display the correct memory name in an error message (previously
hardcoded).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@137 81a1dc3b-b13d-400b-aceb-764788c761c2
joerg_wunsch
bdean
hinni
troth
bsd