* stk500.c (stk500_initialize): Insert dummy values for PAGEL and
BS2 if they are not present in the config file, in order to be able
to proceed with the stk500_set_extended_parms() anyway.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1082 81a1dc3b-b13d-400b-aceb-764788c761c2
will update only the table in pgm_type.c.
* config_gram.y, lexer.l: removed programmer type keywords,
use now locate_programmer_type() function
* pgm_type.[ch]: added new files for table of programmer types
* main.c: allow list of programmer types by -c ?type
* avrdude.conf.in: changed all type keywords to quoted strings
* doc/avrdude.texi: changed description of type definition, list
of valid types is now included from generated file
* doc/Makefile.am: generate list of programmer types for doc
* all programmers [hc]: add xxx_desc string for description of programmer
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1051 81a1dc3b-b13d-400b-aceb-764788c761c2
Each memory image byte is now tagged as it's being read from a file.
Only bytes read from a file will be written or verified (modulo page
granularity requirements).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1007 81a1dc3b-b13d-400b-aceb-764788c761c2
* avr.h: Remove stray semicolon.
* configure.ac: Add check for predefined types uint_t and ulong_t.
* confwin.c: Include "avrdude.h" on top to avoid empty translation
unit warning.
* ppwin.c: (Ditto.)
* ser_win32.c: (Ditto.)
* serbb_win32.c: (Ditto.)
* jtagmkII.c (jtagmkII_recv): remove unreachable "return".
* stk500.c (stk500_initialize): (Ditto.)
* par.c: Test for both, __sun__ and __sun to see whether we are
being compiled on Solaris.
* ppi.c: (Ditto.)
* stk500v2.c: Implement the DEBUG and DEBUGRECV macros in a way
that is compatible with the ISO C99 standard.
* usbtiny.c: Only typedef uint_t and ulong_t if they have not
been found already by the autoconf checks.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@804 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6542: paged_load fails on the MIB510 programming board
* stk500.c: Add a workaround for the different signon sequence on
MIB510 programmers.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@791 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6074: added support for crossbow's MIB510 programmer
* avrdude.conf.in: Add entry for mib510.
* stk500.c: Add special hooks to handle the MIB510 programmer.
It mostly talks STK500v1 protocol but has a special hello and
goodbye sequence, and uses a fixed block size of 256 bytes.
* doc/avrdude.texi: Document support for mib510.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@773 81a1dc3b-b13d-400b-aceb-764788c761c2
"classic" AVRs (AT90, ATtiny, ATmega) in both,
ISP and high-voltage programming modes.
* Makefile.am: Add -lm.
* avrdude.conf.in: Add stk600, stk600pp, and stk600hvsp.
* config_gram.y: Add support for the stk600* keywords.
* lexer.l: (Ditto.)
* pgm.h: Add the "chan" parameter to set_varef().
* stk500.c: (Ditto.)
* serial.h: Add USB endpoint support to struct filedescriptor.
* stk500v2.c: Implement the meat of the STK600 support.
* stk500v2.h: Add new prototypes for stk600*() programmers.
* stk500v2_private.h: Add new constants used in the STK600.
* term.c: Add AREF channel support.
* usb_libusb.c: Automatically determine the correct write
endpoint ID, the STK600 uses 0x83 while all other tools use
0x82. Propagate the EP to use through struct filedescriptor.
* usbdevs.h: Add the STK600 USB product ID.
* tools/get-stk600-cards.xsl: XSL transformation for
targetboards.xml to obtain the list of socket and routing
card IDs, to be used in stk500v2.c (for displaying the
names).
* tools/get-stk600-devices.xsl: XSL transformation for
targetboards.xml to obtain the table of socket/routing cards
and their respective AVR device support for doc/avrdude.texi.
* avrdude.1: Document all the STK600 stuff.
* doc/avrdude.texi: Ditto. Added a new chapter for
Programmer Specific Information.
Thanks to Eirik Rasmussen from Atmel Norway for his support in
getting this code running within that short amount of time!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@768 81a1dc3b-b13d-400b-aceb-764788c761c2
own (duplicate) copy of it.
other files: Constify char pointers.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@725 81a1dc3b-b13d-400b-aceb-764788c761c2
declarations in each file by a central header file "avrdude.h".
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@721 81a1dc3b-b13d-400b-aceb-764788c761c2
- declare a dummy "struct timezone" for some Win32 systems (MinGW)
- fix a few printf() argument types
- get rid off the prevailing "all filedescriptors are of type int"
attitude
The last item required a large sweep across the code, in order to
replace all "int fd"s by "struct filedescriptor *fd"s, and pass
pointers (as we cannot pass a union directly). In return, the
code is now supposed to be fully 64-bit safe, rather than relying
on a 64-bit pointer being converted to a (32-bit) int and back
to a pointer as we did previously.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@694 81a1dc3b-b13d-400b-aceb-764788c761c2
avr_read_byte_default() and avr_write_byte_default (resp.) by directly
calling the latter functions from within all programmers that don't
implement their own read_byte()/write_byte() methods. In turn, make the
read_byte() and write_byte() methods mandatory, and the cmd() method
(direct ISP command) optional instead (it's effectively mandatory for
any programmer using avr_read_byte_default()/avr_write_byte_default()
though). Remove all the pointless cmd() method stubs from those programmers
that don't need it.
Eliminate avr_read_byte() as it was now completely identical to
pgm->read_byte().
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@684 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_paged_write): Send the command and the data
payload within a single write().
patch #5025: Improve stk500.c robustness
Submitted by Matthias Ringwald:
* stk500.c (stk500_open): do not flush the serial line after
getting in sync with the programmer.
patch #5293: stk500.c: no drain after sync (-> allow BTnode
Bootloader to work on cygwin)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@670 81a1dc3b-b13d-400b-aceb-764788c761c2
either firmware version 1 or 2.
* Makefile.am (avrdude_SOURCES): add the new files
stk500generic.c and stk500generic.h.
* avrdude.conf.in: Add the stk500generic programmer type, and
change the "stk500" entry to point to this programmer.
* config_gram.y: Add the stk500generic keyword.
* lexer.l: (Ditto.)
* stk500.c: Change the stk500v1 code to not call exit()
prematurely when failing to open the programmer, but instead
return an error status.
* stk500generic.c: (New file.) Stub programmer implementation.
Probe for either stk500v1 or stk500v2, and adjust the current pgm
appropriately.
* stk500generic.h: (New file.) Declare the public interface(s)
of stk500generic.c.
* doc/avrdude.texi: Document the changed behaviour of stk500.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@663 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #4372: Better synchronization for stk500
Sync three times, and drop any noise inbetween.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@641 81a1dc3b-b13d-400b-aceb-764788c761c2
when passing unsigned char * when char * is in the prototype and vice
versa. Clean these up along with a few others.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@491 81a1dc3b-b13d-400b-aceb-764788c761c2
yesterday's changes (i.e. before rev. 1.10 of ser_posix.c), that is,
exit(1) in case of a timeout. Previously, the upper layers didn't see
the timeout at all.
Quite possible that some of these drivers could handle a timeout more
intelligently though. At least for the rather sophisticated STK500v2
protocol, I think it should be possible to retry the request.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@460 81a1dc3b-b13d-400b-aceb-764788c761c2
switch. The specified baud rate will override the default serial port
baud rate for a particular programmer.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@416 81a1dc3b-b13d-400b-aceb-764788c761c2
* pgm.c: Fixed wrong type for default_open introduced by the cleanup yesterday.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@409 81a1dc3b-b13d-400b-aceb-764788c761c2
Move save/restore-functionality into open/close.
* par.c: open/close now saves/restores PPICTRL, too.
* TODO: exitspecs don't work if RESET is in PPICTRL.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@407 81a1dc3b-b13d-400b-aceb-764788c761c2
than memory device size.
(stk500_paged_write): Send whole block at once.
(stk500_paged_load): Limit blocks read to no bigger than memory
device size.
[Contributed by Bill Somerville <bill@classdesign.com>, this fixes
bug #5713.]
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@376 81a1dc3b-b13d-400b-aceb-764788c761c2
stk500 initialization routine. However, allow one to use the -F
option to ignore a bad return code from that function. I think this
still allows what Joerg intended, i.e., providing a way to still get
into terminal mode so that one can recover from setting bad STK500
values which may keep the chip from entering programming mode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@359 81a1dc3b-b13d-400b-aceb-764788c761c2
available.
* avr910.c (avr910_vfy_cmd_sent): New function.
(avr910_chip_erase): Add support for chip erase.
(avr910_enter_prog_mode): New function.
(avr910_leave_prog_mode): New function.
(avr910_initialize): Add code to select device type and enter prog mode.
(avr910_close): Leave programming mode before closing serial port.
(avr910_read_sig_bytes): New function.
(avr910_initpgm): Add avr910_read_sig_bytes method to pgm initializer.
* avrdude.conf.in: Add note about deprecating devicecode.
Change all occurences of devicecode to stk500_devcode.
Add avr910_devcode to a few parts for testing.
* avrpart.h (struct avrpart): Change devicecode field to stk500_devcode.
(struct avrpart): Add avr910_devcode field.
* config_gram.y: Add K_STK500_DEVCODE and K_AVR910_DEVCODE tokens.
Generate an error if devicecode is found in the config file.
Handle parsing of avr910_devcode and stk500_devcode.
* lexer.l: Handle parsing of avr910_devcode and stk500_devcode.
* pgm.c: Initialize pgm->read_sig_bytes field.
* pgm.h: Add pgm->read_sig_bytes field.
* stk500.c: Use stk500_devcode instead of devicecode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@293 81a1dc3b-b13d-400b-aceb-764788c761c2
ser_posix.c files.
* avr910.c: New file (stubs for avr910 serial programmer).
* avr910.h: New file.
* ser_posix.c: New file.
* ser_win32.c: New file (just stubs for now).
* serial.h: New file.
* stk500.c: Move all the code for accessing the posix serial ports
into ser_posix. This will make a native win32 port easier and allows
the avr910 programmer to share the serial code.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@289 81a1dc3b-b13d-400b-aceb-764788c761c2
command be 128 bytes. This cuts 6 seconds off the programming time
for uploading a 6K file into an AT90S8515 vs the time loading the same
file using a 16 byte buffer, and the response feedback is still good.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@261 81a1dc3b-b13d-400b-aceb-764788c761c2
all on non-paged-memory parts. The problem was that the page size was
defaulting to 256 (maximum for the stk500), but the timeout for a
response from the stk500 before declaring it dead was only 0.5
seconds. But it takes much longer than 0.5 seconds to program 256
bytes, so we just weren't waiting long enough.
Fix this in two ways - increase the timeout to 5 seconds, and decrease
the page size to 16 bytes for non-paged parts. The programming time
for 16 bytes is short enough to provide the user with some feedback
that something is happening.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@260 81a1dc3b-b13d-400b-aceb-764788c761c2
itself is paged as it doesn't appear to work otherwise.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@259 81a1dc3b-b13d-400b-aceb-764788c761c2
haven't been specified in the config file for the part.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@250 81a1dc3b-b13d-400b-aceb-764788c761c2
Jason Kyle for the needed protocol information.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@248 81a1dc3b-b13d-400b-aceb-764788c761c2
programming mode. Use 'retry_pulse' in the per-part specification
that can currently take values of 'reset' or 'sck', the default being
'sck' which preserves the previous behaviour. Some newer parts
indicate that /RESET should be pulsed, while older parts say to pulse
SCK.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@212 81a1dc3b-b13d-400b-aceb-764788c761c2
say whether parts support these programming modes or not. Possible
values for 'serial' are 'yes' or 'no'. Possible values for 'parallel'
are 'yes', 'no', or 'pseudo'. Add a bit mask of flags to the AVRPART
structure to capture these settings. Use these within
stk500_initialize() to set the device parameters correctly.
Defaults for 'serial' and 'parallel' are 'yes' unless specified
otherwise.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@208 81a1dc3b-b13d-400b-aceb-764788c761c2
* .cvsignore: Ignore autoconf files.
* AUTHORS: New file.
* ChangeLog: New file.
* Makefile: Removed file.
* Makefile.am: New file.
* NEWS: New file.
* README: New file.
* bootstrap: New file.
* configure.ac: New file.
* avr.c: Include ac_cfg.h (generated by autoconf).
* config.c: Include ac_cfg.h.
Include config_gram.h instead of y.tab.h.
* config.h: If HAS_YYSTYPE is not defined, define YYSTYPE.
* config_gram.y: Include ac_cfg.h.
* fileio.c: Include ac_cfg.h.
* lexer.l: Include config_gram.h instead of y.tab.h.
* lists.c: Include ac_cfg.h.
* main.c: Include ac_cfg.h.
* par.c: Include ac_cfg.h.
* pgm.c: Include ac_cfg.h.
* ppi.c: Include ac_cfg.h.
* stk500.c: Include ac_cfg.h.
* term.c: Include ac_cfg.h.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@192 81a1dc3b-b13d-400b-aceb-764788c761c2
its own file par.c, leaving low level parallel port accessor routines
in ppi.c to help with portability. Change the programmer type to
'PAR' now instead of 'PPI' - 'PAR' represents the parallel port
programmer type.
Be more liberal with 'static' function declarations within the
programmer implimentation files - these functions should never be
called directly - always use the programmer function references.
There are still a few places in 'main.c' that directly reference the
parallel programmer explicitly (par_getpinmask). These should be
fixed somehow.
Axe a few unused functions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@190 81a1dc3b-b13d-400b-aceb-764788c761c2
joerg_wunsch
rliebscher
springob
mludvig
bdean
hinni
arcanum
troth