PAGEL and BS2 signals and the disposition of the reset pin
('dedicated' or 'io').
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@202 81a1dc3b-b13d-400b-aceb-764788c761c2
its own file par.c, leaving low level parallel port accessor routines
in ppi.c to help with portability. Change the programmer type to
'PAR' now instead of 'PPI' - 'PAR' represents the parallel port
programmer type.
Be more liberal with 'static' function declarations within the
programmer implimentation files - these functions should never be
called directly - always use the programmer function references.
There are still a few places in 'main.c' that directly reference the
parallel programmer explicitly (par_getpinmask). These should be
fixed somehow.
Axe a few unused functions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@190 81a1dc3b-b13d-400b-aceb-764788c761c2
This change represents a name change only. There is currently an
effort to port AVRPROG to other platforms including Linux and Windows.
Since Atmel's programmer binary that's included within their AVR
Studio software is named AVRPROG.EXE on the Windows OS, there is the
chance for confusion if we keep calling this program AVRPROG as well.
Up until now the name hasn't really been a problem since there was no
chance to confuse 'avrprog' on Unix with Atmel's AVRPROG because
Atmel's tools only run on Windows. But with the Unix 'avrprog'
possibly being ported to Windows, I felt a name change was the best
way to avoid problems.
So - from this point forward, my FreeBSD Unix program formerly known
as AVRPROG will subsequently be known as AVRDUDE (AVR Downloader/UploaDEr).
This change also represents a time when the AVRDUDE sources move from
my own private repository to a public repository. This will give
other developers a chance to port AVRDUDE to other platforms and
extend its functionality to support additional programming hardware,
etc.
So goodbye AVRPROG, welcome AVRDUDE!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@170 81a1dc3b-b13d-400b-aceb-764788c761c2
"non-paged" parts. Take advantage of that and use the faster internal
routines of the STK500 for those parts as well.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@162 81a1dc3b-b13d-400b-aceb-764788c761c2
that programmers other than the direct parallel port connection can be
supported.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@159 81a1dc3b-b13d-400b-aceb-764788c761c2
bits. Thanks to Joerg Wunsch for tripping over this.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@143 81a1dc3b-b13d-400b-aceb-764788c761c2
overwriting user-modified configs.
Add read/write instructions for all memory types for ATMEGA103,
ATMEGA128, ATMEGA16, and ATMEGA8.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@132 81a1dc3b-b13d-400b-aceb-764788c761c2
Fix setting of status LEDs under various write-fail conditions.
Add a flag to indicate that a memory type requires the device to
possibly be powered off and back on after a write to it. This is due
to a hardware problem on some Atmel devices, see:
http://www.atmel.com/atmel/acrobat/doc1280.pdf
Add greater verbosity to the part-display code when verbose>1 to
display avrprog's encoding of the defined programming instructions.
This is primarily for debugging purposes.
Part updates:
* add the AT90S4414 part
* add fuse and lock bit access instructions for the AT90S1200,
AT90S4434, and AT90S8515.
* add the pwroff_after_write flag to the fuse bits for the AT90S2333
and AT90S4433 parts
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@123 81a1dc3b-b13d-400b-aceb-764788c761c2
Make the BUFF pin a mask like VCC to allow multiple pins to be
asserted at the same time (STK200 has two buffer enable lines).
Add the STK200 programmer.
Fix EEPROM address line selection for several parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@109 81a1dc3b-b13d-400b-aceb-764788c761c2
used to make the instruction input more readable in the config file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@102 81a1dc3b-b13d-400b-aceb-764788c761c2
serial programming instructions are not very orthoganal, i.e., the
"read fuse bits" instruction on an ATMega103 is an entirely different
opcode and data format from the _same_ instruction for an ATMega163!
Thus, it becomes impossible to have a single instruction encoding
(varying the data) across the chip lines.
This set of changes allows and requires instruction encodings to be
defined on a per-part basis within the configuration file. Hopefully
I've defined the encoding scheme in a general enough way so it is
useful in describing the instruction formats for yet-to-be invented
Atmel chips. I've tried hard to make it match very closely with the
specification in Atmel's data sheets for their parts. It's a little
more verbose than what I initially hoped for, but I've tried to keep
it as concise as I could, while still remaining reasonably flexible.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@100 81a1dc3b-b13d-400b-aceb-764788c761c2
Add support for reading/writing ATMega163 lock and fuse bits.
Unfortunately, in looking at the specs for other ATMega parts, they
use entirely different instruction formats for these commands. Thus,
these routines won't work for the ATMega103, for example.
Add support for sending raw command bytes via the interactive terminal
interface. This allows one to execute any programming instruction on
the target device, whether or not avrprog supports it explicitly or
not. Thus, one can use this feature to program fuse / lock bits, or
access any other feature of a current or future device that avrprog
does not know how to do.
Add in comments, an experimental instruction format in the
configuration file. If this works out, it would allow supporting new
parts and non-orthoganal instructions across existing parts without
making avrprog code changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@99 81a1dc3b-b13d-400b-aceb-764788c761c2
Update read/write status more frequently.
Prefix ATMega parts with an 'm'.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@95 81a1dc3b-b13d-400b-aceb-764788c761c2
Rename the poorly chosen name "bank" to "page" for page addressing.
Atmel calls it "page" in their documentation.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@91 81a1dc3b-b13d-400b-aceb-764788c761c2
checking on the memory parameters for parts that do bank addressing.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@88 81a1dc3b-b13d-400b-aceb-764788c761c2
format using a more human-readable format.
Read part descriptions from the config file now instead of hard-coding
them.
Update usage().
Cleanup unused code.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@79 81a1dc3b-b13d-400b-aceb-764788c761c2
might make part descriptions read in this way and we can use a
different letter for those (p). This will make the parsing easier to
distinguish between the entry types.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@69 81a1dc3b-b13d-400b-aceb-764788c761c2
file. This makes supporting other programmers much easier.
Rename AVRprog.pdf to avrprog.pdf.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@67 81a1dc3b-b13d-400b-aceb-764788c761c2
bdean
joerg_wunsch
troth
bsd