patch #6501: New autotools support for avrdude
* Makefile.am: add @WINDOWS_DIRS@ to SUBDIR
* bootstrap: allow for autconf-2.61 and automake-1.10, too
* configure.ac: fix @WINDOWS_DIRS@ recursion, replace
AC_PROG_CC by AM_PROG_CC_C_O, for esoteric reasons
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@774 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6074: added support for crossbow's MIB510 programmer
* avrdude.conf.in: Add entry for mib510.
* stk500.c: Add special hooks to handle the MIB510 programmer.
It mostly talks STK500v1 protocol but has a special hello and
goodbye sequence, and uses a fixed block size of 256 bytes.
* doc/avrdude.texi: Document support for mib510.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@773 81a1dc3b-b13d-400b-aceb-764788c761c2
Add check for buffermode feature, and use it if present. Can be
turned off using -x no_blockmode.
* avr910.c: Implement buffermode test and usage.
* avrdude.1: Document -x no_blockmode.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@771 81a1dc3b-b13d-400b-aceb-764788c761c2
"classic" AVRs (AT90, ATtiny, ATmega) in both,
ISP and high-voltage programming modes.
* Makefile.am: Add -lm.
* avrdude.conf.in: Add stk600, stk600pp, and stk600hvsp.
* config_gram.y: Add support for the stk600* keywords.
* lexer.l: (Ditto.)
* pgm.h: Add the "chan" parameter to set_varef().
* stk500.c: (Ditto.)
* serial.h: Add USB endpoint support to struct filedescriptor.
* stk500v2.c: Implement the meat of the STK600 support.
* stk500v2.h: Add new prototypes for stk600*() programmers.
* stk500v2_private.h: Add new constants used in the STK600.
* term.c: Add AREF channel support.
* usb_libusb.c: Automatically determine the correct write
endpoint ID, the STK600 uses 0x83 while all other tools use
0x82. Propagate the EP to use through struct filedescriptor.
* usbdevs.h: Add the STK600 USB product ID.
* tools/get-stk600-cards.xsl: XSL transformation for
targetboards.xml to obtain the list of socket and routing
card IDs, to be used in stk500v2.c (for displaying the
names).
* tools/get-stk600-devices.xsl: XSL transformation for
targetboards.xml to obtain the table of socket/routing cards
and their respective AVR device support for doc/avrdude.texi.
* avrdude.1: Document all the STK600 stuff.
* doc/avrdude.texi: Ditto. Added a new chapter for
Programmer Specific Information.
Thanks to Eirik Rasmussen from Atmel Norway for his support in
getting this code running within that short amount of time!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@768 81a1dc3b-b13d-400b-aceb-764788c761c2
and turn stderr into unbuffered output while producing the
progress report.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@765 81a1dc3b-b13d-400b-aceb-764788c761c2
definition. If present, call the setup hook immediately after finding
the respective programmer object, and schedule the teardown hook to be
called upon exit. This allows the programmer implementation to
dynamically allocate private programmer data.
avr910.c, butterfly.c, jtagmkI.c, jtagmkII.c, stk500v2.c, usbasp.c,
usbtiny.c: Convert static programmer data into dynamically allocated
data.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@764 81a1dc3b-b13d-400b-aceb-764788c761c2
the programmer backend.
jtagmkII.c: Implement the extended parameter jtagchain=
to support JTAG daisy-chains.
avrdude.1, doc/avrdude.texi: Document all of the above.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@761 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #5007: Patch for line-buffering of stdout and stderr
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@757 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6121: ISP support for the C2N232I device (serial port
bitbanging)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@755 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6141: accept binary format immediate values
Detect a 0b prefix, and call strtoul() differently in that case.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@754 81a1dc3b-b13d-400b-aceb-764788c761c2
In ser_recv(): Drop the essentially unused variable "len", and use the
variable "read" in order to track how many bytes have just been read
in.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@753 81a1dc3b-b13d-400b-aceb-764788c761c2
Add definitions for the ATmega329P/3290P. Same as ATmega329/3290
except of the different signature.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@752 81a1dc3b-b13d-400b-aceb-764788c761c2
using default configuration file.
Uncomment the (bogus) stk500_devcode lines for the ATmega164P,
ATmega324P, ATmega644, and ATmega644P definitions. This only affects
users of STK500v1 firmware.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@750 81a1dc3b-b13d-400b-aceb-764788c761c2
"BOOT"-type code, while the standard codes are different (usually one
below).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@740 81a1dc3b-b13d-400b-aceb-764788c761c2
paged_write backend functions iff the memory area in question has
a page_size != 0.
This is supposed to fix bug #19234: avrdude-5.3.1 segfaults when
stk500v1 tries to program an ATtiny15
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@739 81a1dc3b-b13d-400b-aceb-764788c761c2
resp. Add an entry for the ATmega644P.
Fixes bug #19769: ATmega164p not recognized
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@737 81a1dc3b-b13d-400b-aceb-764788c761c2
something to the serial line. That kind of polling isn't very useful
anyway, and it seems it breaks for the Linux CP210x USB<->RS-232
bridge driver which is certainly a bug in the driver, but we can just
avoid that bug alltogether.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@736 81a1dc3b-b13d-400b-aceb-764788c761c2
ATmega640/1280/1281/2560/2561. Atmel has changed the XML
files after the initial release.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@735 81a1dc3b-b13d-400b-aceb-764788c761c2
*Problem in verbose output of previous commit. I hoped to
have all the verbose changes in a single commit, but that
won't happen...
*Main thing is fixed safemode to turn itself off when you can't
read the fuses anyway. I don't know what I was thinking when
I made it fail out of programmers that don't support fuse reading.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@733 81a1dc3b-b13d-400b-aceb-764788c761c2
include the documentation into the tarball even if the configure had been
run without the --enable-doc.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@726 81a1dc3b-b13d-400b-aceb-764788c761c2
own (duplicate) copy of it.
other files: Constify char pointers.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@725 81a1dc3b-b13d-400b-aceb-764788c761c2
list_parts() and list_programmers() functions into general list
iteration functions that call a caller-supplied callback for each
element. Implement list_parts() and list_programmers() as private
functions in main.c based on that approach.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@724 81a1dc3b-b13d-400b-aceb-764788c761c2
and link main.c against that library.
Add AC_PROG_RANLIB to configure.ac as we are building a library now.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@723 81a1dc3b-b13d-400b-aceb-764788c761c2
- Make all internal functions "static".
- Make sure each module's header and implementation file match.
- Remove all library-like functionality from main.c, so only
the actual frontend remains in main.c.
- Add C++ brackets to all header files.
That effectively leaves the various module C files as something like
an "avrdude library", with main.c being the currently only frontend
program for that library. In theory, it should be possible to write
different frontends using the same library backend functions though.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@722 81a1dc3b-b13d-400b-aceb-764788c761c2
declarations in each file by a central header file "avrdude.h".
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@721 81a1dc3b-b13d-400b-aceb-764788c761c2
and EEPROM, based on the current Atmel XML file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@720 81a1dc3b-b13d-400b-aceb-764788c761c2
and the presence of the header ddk/hidsdi.h. It now works
correctly under Cygwin and several flavours of MinGW.
* Makefile.am: Add new LIBHID pattern.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@719 81a1dc3b-b13d-400b-aceb-764788c761c2
command (which is ignored by current AVR109 bootloaders),
send the first reply from the list of supported device
codes back rather than using avrdude.conf's idea about
an AVR910 device code. Apparently, this solves disagreements
between different versions of at least the ATmega8 AVR910
device code.
Closes bug #18727: Writing flash failed
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@718 81a1dc3b-b13d-400b-aceb-764788c761c2
Change HVSP reset timing for ATtiny25/45/85 from
500 microseconds to 1 ms, matching the most recent Atmel XML
specs.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@717 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (frank-stk200): Fix syntax error.
* ser_avrdoper.c: Make #ifdef for Win32/libhid
consistent with the initial check: use the HID driver
only iff found, otherwise use libusb.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@712 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (frank-stk200): New programmer added.
Closes patch #5502: one other programmer
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@706 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #5507: Support for AVR-Doper USB programmer in HID mode
* configure.ac: Add hooks to detect the Win32 HID library,
as well as the existence of <ddk/hidsdi.h>.
* Makefile.am: Add new files.
* my_ddk_hidsdi.h: (New file.)
* ser_avrdoper.c: (New file.)
* serial.h: Add declaration for avrdoper_serdev.
* stk500v2.c: Add hook to divert to the AVR Doper code.
* avrdude.1: Document the AVR Doper support.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@704 81a1dc3b-b13d-400b-aceb-764788c761c2
usleep(1000000) that accidentally crept in in rev 1.19.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@702 81a1dc3b-b13d-400b-aceb-764788c761c2
value in case we had changed it.
Fixes bug #18262: JTAGMKI/JTAG1 Reset Bug
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@699 81a1dc3b-b13d-400b-aceb-764788c761c2
fallback from each programmer's paged_load() or paged_write()
method, respectively. The return value needs to be checked for
being greater or equal than 0 rather equal to 0 in order to
assume the operation has been successful.
Fixes bug #18489: avrdude is too slow (20 byte/s)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@695 81a1dc3b-b13d-400b-aceb-764788c761c2
- declare a dummy "struct timezone" for some Win32 systems (MinGW)
- fix a few printf() argument types
- get rid off the prevailing "all filedescriptors are of type int"
attitude
The last item required a large sweep across the code, in order to
replace all "int fd"s by "struct filedescriptor *fd"s, and pass
pointers (as we cannot pass a union directly). In return, the
code is now supposed to be fully 64-bit safe, rather than relying
on a 64-bit pointer being converted to a (32-bit) int and back
to a pointer as we did previously.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@694 81a1dc3b-b13d-400b-aceb-764788c761c2
upon failure now that the upper layers won't fall back to the cmd()
method anymore in that case.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@691 81a1dc3b-b13d-400b-aceb-764788c761c2
(according to the XML files).
Add an XSL stylesheet to extract the dW
parameters from the XML files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@690 81a1dc3b-b13d-400b-aceb-764788c761c2
imposed by debugWire itself, so effectively, only flash ROM can be
read and written.
Currently, the required changes to avrdude.conf.in are only present
for the ATtiny44.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@688 81a1dc3b-b13d-400b-aceb-764788c761c2
avr_read_byte_default() and avr_write_byte_default (resp.) by directly
calling the latter functions from within all programmers that don't
implement their own read_byte()/write_byte() methods. In turn, make the
read_byte() and write_byte() methods mandatory, and the cmd() method
(direct ISP command) optional instead (it's effectively mandatory for
any programmer using avr_read_byte_default()/avr_write_byte_default()
though). Remove all the pointless cmd() method stubs from those programmers
that don't need it.
Eliminate avr_read_byte() as it was now completely identical to
pgm->read_byte().
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@684 81a1dc3b-b13d-400b-aceb-764788c761c2
when closing the connection. They cause the activity LED on the ICE
to continue to flicker, and are not necessary anyway (the target
starts to run by itself when leaving programmng mode).
This is a partial fix for bug #18262: JTAGMKI/JTAG1 Reset Bug
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@683 81a1dc3b-b13d-400b-aceb-764788c761c2
that indicates whether the underlying communication can dynamically
change its speed or not. This flag is set for true serial
communication but clear for USB communication. Don't try to adjust
the speed when talking over a communication channel that doesn't
support it. (The Dragon does not even support the respective
parameter.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@676 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500.c (stk500_paged_write): Send the command and the data
payload within a single write().
patch #5025: Improve stk500.c robustness
Submitted by Matthias Ringwald:
* stk500.c (stk500_open): do not flush the serial line after
getting in sync with the programmer.
patch #5293: stk500.c: no drain after sync (-> allow BTnode
Bootloader to work on cygwin)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@670 81a1dc3b-b13d-400b-aceb-764788c761c2
Add the CoreFoundation and IOKit framework linker flags on MacOS X
when configuring for USB support.
patch #4685: Libusb on MacOS X: detection and additional includes
Thanks to Matthias Ringwald for testing the reworked patch.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@666 81a1dc3b-b13d-400b-aceb-764788c761c2
device codes, allow the user to override the device code
verification with the -F option.
* main.c: Make ovsigck a global variable.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@665 81a1dc3b-b13d-400b-aceb-764788c761c2
either firmware version 1 or 2.
* Makefile.am (avrdude_SOURCES): add the new files
stk500generic.c and stk500generic.h.
* avrdude.conf.in: Add the stk500generic programmer type, and
change the "stk500" entry to point to this programmer.
* config_gram.y: Add the stk500generic keyword.
* lexer.l: (Ditto.)
* stk500.c: Change the stk500v1 code to not call exit()
prematurely when failing to open the programmer, but instead
return an error status.
* stk500generic.c: (New file.) Stub programmer implementation.
Probe for either stk500v1 or stk500v2, and adjust the current pgm
appropriately.
* stk500generic.h: (New file.) Declare the public interface(s)
of stk500generic.c.
* doc/avrdude.texi: Document the changed behaviour of stk500.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@663 81a1dc3b-b13d-400b-aceb-764788c761c2
AT90S1200 and the AT90S8515, fuse bit handling via ISP, and lock bit
reading via ISP are not supported at all. For the AT90S4414 (small
brother of the AT90S8515), add the ability to write the lock bits, and
add a definition for the fuse bits (usable for HV programming). For
the AT90S2313, add the "fuse" memory range, so it's available for HV
programming.
Resolves bug #17796: avrdude will not program or verify lockbits with
Atmel STK protocol programmers
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@662 81a1dc3b-b13d-400b-aceb-764788c761c2
* usbasp.c: Check for USBasp with new as well as old VID/PID
pair, warn the user about upgrading the firmware in case an
old one has been found.
* usbasp.h: Add new VID/PID.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@661 81a1dc3b-b13d-400b-aceb-764788c761c2
. high fuse has 8 bits
. there is an extended fuse (just one bit)
. the calibration area is only 1 byte
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@660 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch
Thomas Fischl
Colin O Flynn