* stk500v2.c: For the "flash" pseudo-memory of Xmega devices,
distinguish addresses between "application" and "boot" area.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1081 81a1dc3b-b13d-400b-aceb-764788c761c2
program header segment, subtract `low' from ph[n].p_paddr in order
to correct the magic section offsets for the AVR's non-flash
memory regions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1080 81a1dc3b-b13d-400b-aceb-764788c761c2
any given section maps straight to a program header segment, use a
more sophisticated decision that matches any section as long as it
fits into the segment. This is needed for situations where the
program header segment spans a larger area than the section data
provided. (This can e.g. happen in an ELF file that contains no
data at address 0, like a bootloader only.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1079 81a1dc3b-b13d-400b-aceb-764788c761c2
firmware >= V7.x)
* jtagmkII.c: Add firmware-version dependent handling of Xmega parameters.
V7.x firmware expects the NVM offsets being specified through the Xmega
parameters command, but left out as part of the memory address itself.
* jtagmkII_private.h: Add CMND_SET_XMEGA_PARAMS, and struct xmega_device_desc.
* config_gram.y: Add mcu_base keyword.
* avrpart.h: (Dito.)
* lexer.l: (Dito.)
* avrdude.conf.in (.xmega): add mcu_base, and data memory segment.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1078 81a1dc3b-b13d-400b-aceb-764788c761c2
firmware < V7.x)
* jtagmkII.c: When going to write to the boot section of flash,
use MTYPE_BOOT_FLASH rather than MTYPE_FLASH
* jtagmkII_private.h: add MTYPE_BOOT_FLASH constant
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1077 81a1dc3b-b13d-400b-aceb-764788c761c2
supported error
* stk500v2.c: Handle all Xmega memory sections (except
"prodsig" which is not documented in AVR079)
* fileio.c: Treat the "boot", "application", and "apptable"
regions (which are actually subregions of "flash") all as
being flash, i.e. suppress trailing 0xFF bytes when reading
them
* avr.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1075 81a1dc3b-b13d-400b-aceb-764788c761c2
"GO" code in again, but only activate it when programming an
Xmega device through PDI.
Wonderfully consistent tools.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1071 81a1dc3b-b13d-400b-aceb-764788c761c2
turned out to do more harm than good; on the Xmega, it caused exactly
the opposite reaction, the CPU stopped. Even without it, after the
RESET command, the target is running already. So, drop the GO.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1070 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrftdi.[ch]: moved global data into private data structure, moved
private defines from header file into source file
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1068 81a1dc3b-b13d-400b-aceb-764788c761c2
(generating the programmers lists)
* doc/avrdude.texi: Add include of generated table of programmers
* doc/Makefile.am: Add generating of table of programmers in programmers.texi
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1062 81a1dc3b-b13d-400b-aceb-764788c761c2
* ft245r.[ch]: new programmer type implementation
* configure.ac: add pthread as link library
* avrdude.conf.in: added some new programmers
* Makefile.am: added new source files to compile
* pindefs.h: change PIN_MASK, PIN_INVERSE to highest bit of unsigned int
* pgm.[ch]: added generic function to print pin assignments (taken from par.c)
* par.c: moved pin assigment print function to pgm.c
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1055 81a1dc3b-b13d-400b-aceb-764788c761c2
* config.[hc]: removed unused function id(), use value.type to select
values
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1053 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7686 Updating buspirate ascii mode to current firmware, use AUX
as clock generator, and setting of serial receive timeout
* buspirate.c: added paged_write, changed binary mode setup/detection,
added clock output on AUX pin
* avrdude.1: updated documentation
* doc/avrdude.texi: updated documentation
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1052 81a1dc3b-b13d-400b-aceb-764788c761c2
will update only the table in pgm_type.c.
* config_gram.y, lexer.l: removed programmer type keywords,
use now locate_programmer_type() function
* pgm_type.[ch]: added new files for table of programmer types
* main.c: allow list of programmer types by -c ?type
* avrdude.conf.in: changed all type keywords to quoted strings
* doc/avrdude.texi: changed description of type definition, list
of valid types is now included from generated file
* doc/Makefile.am: generate list of programmer types for doc
* all programmers [hc]: add xxx_desc string for description of programmer
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1051 81a1dc3b-b13d-400b-aceb-764788c761c2
nounput. This gets rid of a compiler warning, so we are warning-free
again.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1048 81a1dc3b-b13d-400b-aceb-764788c761c2
trying to hard-code the default port name in main.c.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1047 81a1dc3b-b13d-400b-aceb-764788c761c2
abstract .xmega part as parent for xmegas
* main.c: hide parts starting with '.' from parts list
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1046 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: updated documentation comment and some programmers
have now parents
* config_gram.y: initpgm will now called at first use of programmer
in main. parser sets only the function pointer in the pgm structure.
Pin and pin lists definitions can now be empty to remove the parents
setting.
* doc/avrdude.texi: updated documentation
* main.c: added call to pgm->initpgm after locate_programmer
* pgm.[hc]: added field initpgm in structure, added function pgm_dup
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1045 81a1dc3b-b13d-400b-aceb-764788c761c2
to lusb0_usb.h (for whatever reason). Autoprobe for the filename
during configure, and include whatever is appropriate.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1043 81a1dc3b-b13d-400b-aceb-764788c761c2
functions. So a negative return code led never to a fallback to byte
functions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1042 81a1dc3b-b13d-400b-aceb-764788c761c2
* config_gram.y: if memory section is overwritten old entry is removed
(not in original patch)
* config_gram.y: if programmer or part is defined twice, a warning is
output and the first instance is removed
General cleanup and free functions, so valgrind does not report any lost
blocks at program end.
* avrpart.[hc]: added avr_free_(opcode|mem|part) functions
* pgm.[hc]: added pgm_free function
* update.[hc]: added free_update functions
* config.[hc]: added cleanup_config function, use yylex_destroy to reset
the lexer after usage. (So it can be reused.)
* main.c: add cleanup_main function which is called by atexit() (This
frees all lists so that at program exit only really lost memory is
reported by valgrind.)
* usbasp.c: added libusb_free_device_list() and libusb_exit() calls to
avoid lost memory
* buspirate.c: moved memory allocation from initpgm to setup and added
free in teardown
* configure.ac: add definition of HAVE_YYLEX_DESTROY if $LEX is flex.
* Makefile.am: added . in front of SUBDIRS to build avrdude before trying
to use it for creating the part list for the docs.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1041 81a1dc3b-b13d-400b-aceb-764788c761c2
id "usbasp" nibobee and old usbasp are tried as they were currently
implemented within usbasp
* avrdude.conf.in: added usb params to "usbasp", added new entry "nibobee"
with params which were hardcoded in usbasp.c, and added an entry
"usbasb-clone" which only checks vid/pid.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1040 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrftdi.c: Fixed interface and implementation of avrftdi_paged_(write|load)
patch #7672 adding support for O-Link (FTDI based JTAG) as programmer
* avrdude.conf.in: added o-link entry
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1039 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #35208: avrdude 5.11 on freebsd 8.2-STABLE does not reset
Arduino Uno properly
* arduino.c (arduino_open): Bump the timeout between pulling
the DTR and RTS lines low and high.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1036 81a1dc3b-b13d-400b-aceb-764788c761c2
* avr910.c:625 (error) Possible null pointer dereference: cmd - otherwise it is redundant to check if cmd is null at line 624
* avr910.c:626 (error) Possible null pointer dereference: cmd - otherwise it is redundant to check if cmd is null at line 624
* avr910.c:168 (information) The scope of the variable 'devtype_1st' can be reduced
* avr910.c:169 (information) The scope of the variable 'dev_supported' can be reduced
* avrftdi.c:647 (error) Using sizeof for array given as function argument returns the size of pointer.
* stk500v2.c:3347 (error) Memory leak: b
* stk500v2.c:3452 (error) Memory leak: b
* usbasp.c:554 (error) Using sizeof for array given as function argument returns the size of pointer.
* usbasp.c:485 (information) The scope of the variable 'dly' can be reduced
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1035 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Added m48p with parent m48 + different signature
* avrdude.conf.in: made part parents (m88p = m88 + different signature, m168p = m168 + different signature)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1033 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #30438 efuse bits written as 0 on at90pwmxx parts
* avrdude.conf.in: (pwm2, pwm2b, pwm3, pwm3b) <efuse.write>: Write
eight bits
* avrdude.conf.in: made part parents (pwm3 = pwm2, pwm3b = pwm2b,
pwm2b = pwm2 + different signature)
* ChangeLog-2011: New file, rotate ChangeLog for new year.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1032 81a1dc3b-b13d-400b-aceb-764788c761c2
* doc/avrdude.texi: Added missing options to part definition
* config_gram.y: Fixed resetting of is_at90s1200 and is_avr32 flags
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1031 81a1dc3b-b13d-400b-aceb-764788c761c2
non-standard baud rates (only baud rates up to B38400 are
standardized by the Single UNIX Specification).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1029 81a1dc3b-b13d-400b-aceb-764788c761c2
(not in original patch)
* avrpart.c: New function avr_dup_opcode. avr_dup_mem/avr_dup_part-
functions now duplicate the opcodes in their op-array to avoid memory leaks.
* doc/avrdude.texi: Added description of part parent f
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1028 81a1dc3b-b13d-400b-aceb-764788c761c2
* doc/Makefile.am: Add rule how to create avrdude before generating parts list
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1027 81a1dc3b-b13d-400b-aceb-764788c761c2
(Extended Linear Address Record)
Replace the change from r928 (handling of 0x8000000 offset in AVR32
files) by a completely different logic that no longer breaks hex files
for other devices starting with an offset; also apply a similar change
to S-record files, as well as when writing files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1017 81a1dc3b-b13d-400b-aceb-764788c761c2
it has been explicitly requested (by -y or -Y), rather than always
attempting to read the last EEPROM bytes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1014 81a1dc3b-b13d-400b-aceb-764788c761c2
Fix regression in the AVRISPmkII/STK600 TPI handling introduced
by the USBasp's TPI implementation which added a pagesize even for
the minor memory regions of TPI devices. Also fix wrong offset
introduced by the memory tagging patch.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1009 81a1dc3b-b13d-400b-aceb-764788c761c2
their programmer doesn't provide a (low-level) cmd_tpi method;
instead, fall back to the normal programmer methods which are
supposed to handle the situation.
This fixes a regression where the recent bitbang-TPI implementation
broke TPI handling of STK600/AVRISPmkII.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1008 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk500v2_initialize): For the AT90S1200, release
/RESET for a moment before reinitializing, as this is required by
its programming protocol.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1004 81a1dc3b-b13d-400b-aceb-764788c761c2
than ftdi_init(), as this is a more specific thing to search for in
order to make sure getting a recent enough libftdi.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1003 81a1dc3b-b13d-400b-aceb-764788c761c2
programmers)
* config_gram.y: Introduce new keyword "is_at90s1200".
* lexer.l: (Ditto.)
* avrdude.conf.in: Applew new keyword to the AT90S1200 device.
* avrpart.h: Introduce new flag AVRPART_IS_AT90S1200, reflecting
the is_at90s1200 configuration keyword.
* bitbang.c (bitbang_initialize): Replace existing test for
AT90S1200 by AVRPART_IS_AT90S1200
* avr.c (avr_write_byte_default): Avoid the pre-write reading for
the AT90S1200, as this appears to sometimes corrupt the high byte
by pre-programming the low byte just written into it.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@1002 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7056: adding support for mikrokopter bootloader to butterfly
* butterfly.c: Add some specific logic to handle the
mikrokopter.de butterfly bootloader.
* butterfly.h: Add one related function declaration.
* config_gram.y: Add butterfly_mk keyword.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add entry for butterfly_mk.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@991 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf (jtagkey): Add a definition for the Amontec
JTAGKey
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@986 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #22720: avrdude-5.5 ignores buff settings in avrdude.conf
(Note that the actual bug the subject is about has been fixed
long ago.)
* update.c (do_op): fix a diagnostic message
* pgm.h: add exit_datahigh field
* par.c: set and act upon the exit_datahigh field
* avrdude.1: document the new -E options
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@985 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtagII.c (jtagmkII_getsync): Instead of exit()ing from
deep within the tree when detecting the "need debugWIRE"
situation, properly pass this up as a return code.
* jtagII_private.h (JTAGII_GETSYNC_FAIL_GRACEFUL): New constant.
* stk500v2.c (stk500v2_jtagmkII_open): Don't tell anything
anymore when receiving a JTAGII_GETSYNC_FAIL_GRACEFUL from
jtagmkII_getsync(); silently give up (all necessary has been
said already).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@983 81a1dc3b-b13d-400b-aceb-764788c761c2
* usbasp.c (libusb_to_errno): Conditionalize some error codes
that apparently are lacking on MinGW.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@982 81a1dc3b-b13d-400b-aceb-764788c761c2
* ser_avrdoper.c: add <stdlib.h> so exit() is declared.
* usbtiny.c (usbtiny_open): provide an initializer to a
"may be used uninitialized" variable (since GCC could not
fully detect the logic behind).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@981 81a1dc3b-b13d-400b-aceb-764788c761c2
Wolfgang Moser, Ville Voipio, Hannes Weisbach
patch #7486: Patch to add FT2232C/D, FT2232H, FT4232H,
usbvid, usbpid, usbdev for USB support - Based on #7062
* avrftdi.c: New file.
* avrftdi.h: (Ditto.)
* configure.ac: Add check for libftdi.
* config_gram.y: Add AVRFTDI and per-programmer USB string
keywords.
* lexer.l: (Ditto.)
* avrdude.conf.in: Add avrftdi and 2232HIO programmers.
* pgm.h: Add USB parameters.
* Makefile.am: Add avrftdi.c and avrftdi.h.
* AUTHORS: Mention the new authors.
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@979 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #31779: Add support for addressing usbtinyisp with -P option
* usbtiny.c (usbtiny_open): Add logic to distinguish multiple USBtinyISP
programmers by their bus:device tuple.
* doc/avrdude.texi: Document the new functionality.
* avrdude.1: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@974 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #30268: Debugwire broken in avrdude-5.10
* jtagmkII.c (jtagmkII_initialize): only try setting up a JTAG chain when
the programmer is using JTAG.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@973 81a1dc3b-b13d-400b-aceb-764788c761c2
on the AVRISP-MKII
* stk500v2.c (stk500v2_program_enable): Rewrite the logic to
explain ISP activation failures.
* stk500v2_private.h: Fix the various STATUS_* constants;
AVR069 and AVR079 disagreed in their values, even though they
are apparently implementing the same logic behind.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@972 81a1dc3b-b13d-400b-aceb-764788c761c2
ATtiny88, ATmega168, ATmega168P, ATmega328P): Bump delay value for STK500v2
EEPROM write operation to 5, according to the respective XML files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@970 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #31386: A "BUILD.svn" or similar "how to get started" doc would be helpful
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@967 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #32539: [Documentation][Patch] Man page is misleading re: Dragon & PDI
Update information about PDI connections on AVR Dragon
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@966 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #33345: File auto detection as binary doesn't open
file in binary mode on Windows
* fileio.c: Move the decision about opening files in
binary mode until before the fopen() call.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@964 81a1dc3b-b13d-400b-aceb-764788c761c2
timeout should depend on the selected clock speed, but changing the
API for that would require quite some effort throughout the entire
code base.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@954 81a1dc3b-b13d-400b-aceb-764788c761c2
Thanks to Vitaly Chernookiy for the patch.
* avrdude.conf.in: Add support for atmega324pa.
* ChangeLog-2010: New file, rotate ChangeLog for new year.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@953 81a1dc3b-b13d-400b-aceb-764788c761c2
programming stability, in particular with the STK600.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@952 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk500v2_open): use same condition to refer to the AVR
Doper support as used in the definition in ser_avrdoper.c.
(Thanks to Christian Starkjohann for the analysis of the problem.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@947 81a1dc3b-b13d-400b-aceb-764788c761c2
doc/avrdude.texi (Troubleshooting): Mention the libusb 0.1 API
wrapper issue that is present in some Linux versions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@944 81a1dc3b-b13d-400b-aceb-764788c761c2
* doc/avrdude.texi: Remove the recommendation for building
Win32 binaries under Cygwin; mention MinGW as an alternative
environment.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@942 81a1dc3b-b13d-400b-aceb-764788c761c2
* windows/Makefile.am (loaddrv_LDFLAGS): remove, the -mno-cygwin
flag is supposed to be set in CFLAGS by ./configure
* configure.ac: add a check for the presence of usleep(), add a
check whether the linker accepts -static
* avrdude.h: protect prototype for usleep by !defined(HAVE_USLEEP)
* ppwin.c (usleep): protect by !defined(HAVE_USLEEP)
* main.c: silence "array subscript of type char" compiler warnings
by casting all arguments to tolower()/toupper() and isspace()/
isdigit()/ispunct() to "int"
* butterfly.c: (Dito.)
* avr910.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@936 81a1dc3b-b13d-400b-aceb-764788c761c2
* configure.ac: For Win32 environments, add a check whether the
compiler understands the -mno-cygwin option. If not, don't use
it but suggest using a different compiler.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@930 81a1dc3b-b13d-400b-aceb-764788c761c2
0x10000 bytes
* fileio.c: Revert the changes from r851 and r880, respectively.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@928 81a1dc3b-b13d-400b-aceb-764788c761c2
external reset applied (in case the target is in sleep mode or has
asserted the JTD bit).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@926 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #28611: -i delay not being applied to all serial port
bit banging state transitions
* serbb_win32.c: Apply ispdelay everywhere.
* serbb_posix.c: (Dito.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@917 81a1dc3b-b13d-400b-aceb-764788c761c2
Add ATtiny4/5/9/10 to avrdude.conf.in.
Document TPI and new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@916 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6927: Documentation patches
* doc/avrdude.texi: Fix various typos, and remove the last
remnants of obsoleted options -i/-o/-m/-f.
* avrdude.1: Merge typo fixes from avrdude.texi where
applicable.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@914 81a1dc3b-b13d-400b-aceb-764788c761c2
unallocated memory (in the atexit handler) in case of bailing out.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@910 81a1dc3b-b13d-400b-aceb-764788c761c2
jtagmkII_private.h, drop all #if 0 blocks, fold overly long lines,
move the *_initpgm() functions to the end of the file; while being
here, remove all trailing whitespace.
* jtagmkII_private.h: move AVR32 #defines here.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@909 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in: Correctly declare EEPROM page sizes for
all Xmega devices (0x20 instead of 0x100).
* avr.c: If a memory region has a page size declared, try
using the paged IO routines regardless of the target memory
name. Xmega EEPROM requires to be written in paged mode.
Correctly use a long (rather than unsigned long) variable to
evaluate the success status of the paged mode write attempt.
* stk500v2.c: Don't apply TIF space offsets twice (bug #27995:
AVRDUDE 5.8svn fails to program and read XMEGA); use
stk500v2_loadaddr() prior to paged mode (EEPROM and flash) writes,
otherwise programming of flash areas will fail; while being there,
check the return value of stk500v2_loadaddr() everywhere; use the
correct write/erase mode bits (same as AVR Studio does).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@907 81a1dc3b-b13d-400b-aceb-764788c761c2
subsequent programming operation will fail (for unknown reasons).
Actually, this was really only required for ancient AVRs, but doesn't
hurt on mega and tiny devices.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@904 81a1dc3b-b13d-400b-aceb-764788c761c2
* jtagmkII_private.h: Add CMND_XMEGA_ERASE as well as
the various XMEGA_ERASE_* definitions (from updated
appnote AVR067)
* jtagmkII.c (jtagmkII_chip_erase): Correctly implement
Xmega chip erase based on CMND_XMEGA_ERASE.
* jtagmkII.c (jtagmkII_pre_write): Remove, this turned out
to be just a chip erase.
* jtagmkII.c (jtagmkII_program_disable): Don't try reading
"hfuse" for Xmega parts; they don't have it.
* main.c (main): Re-enable auto-erase. It's been done
before (as "jtagmkII_pre_write") in jtagmkII_paged_write()
anyway. Xmega boot and application flash areas should be
handled separately in the future, so auto_erase can only
affect the area just being programmed.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@903 81a1dc3b-b13d-400b-aceb-764788c761c2
to a standard a reset command assume it was in binmode
and attempt to exit to text mode first.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@901 81a1dc3b-b13d-400b-aceb-764788c761c2
level.
* buspirate.c: Fix Win32 build warning: include <malloc.h> to
to get a declaration for alloca().
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@898 81a1dc3b-b13d-400b-aceb-764788c761c2
* usbasp.c: Change blocksize depending on sck frequency to avoid usb transmition timeouts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@897 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c: Fix the "bad response to GO command:
RSP_ILLEGAL_EMULATOR_MODE" message. jtagmkII_close()
has been called with the wrong pgm->cookie. Wrap it
inside stk500v2_jtagmkII_close(), adjusting the cookie
data appropriately.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@895 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #7010: Win32 enhanced bitbang_delay
* bitbang.c (bitbang_calibrate_delay, bitbang_delay): On Win32,
use the high-resolution performance counter rather than the
uneducated delay loop guess if it is available on the target
hardware.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@894 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #27596: AT90s2333 is not correctly supported in avrdude.conf
* avrdude.conf.in (at90s2333): add various STK500v2 parameters.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@889 81a1dc3b-b13d-400b-aceb-764788c761c2
* par.c (par_close): use par_setmany() rather than par_setpin()
for PPI_AVR_BUFF.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@888 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk500v2_dragon_isp_initpgm): Use
stk500v2_jtagmkII_setup/stk500v2_jtagmkII_rather than their
jtagII counterparts, to get the private data properly
initialized.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@887 81a1dc3b-b13d-400b-aceb-764788c761c2
by recent GCC versions).
* config_gram.y (parse_cmdbits): "brkt possibly used uninitialized"
(GCC errs here)
* jtagmkII.c (jtagmkII_reset32): "status possibly used uninitialized"
(I think GCC errs, too)
* buspirate.c: "pointers differ in signedness" (mismatch between
string processing and the use of "unsigned char" throughought the
AVRDUDE API)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@882 81a1dc3b-b13d-400b-aceb-764788c761c2
takes only 14 sec instead of almost 2 mins with the original
implementation.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@844 81a1dc3b-b13d-400b-aceb-764788c761c2
conditional compilation of usb_reset() introduced in r798.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@841 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #26527: bug in unicode conversion
* ser_avrdoper.c (convertUniToAscii): when encountering a UTF-16
character that cannot be converted to ASCII, increment the UTF-16
pointer anyway when proceeding.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@837 81a1dc3b-b13d-400b-aceb-764788c761c2
out of the chaining of both, the stk500v2 and the jtagmkII
programmers for some programming hardware (JTAG ICE mkII and AVR
Dragon running in ISP, HVSP or PP mode), where both programmers
have to maintain their private programmer data.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@834 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (atmega163): fill in stk500v2 parameters, correct
some flash programming parameters as well.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@827 81a1dc3b-b13d-400b-aceb-764788c761c2
* ser_posix.c (ser_setspeed): Don't pass TCSAFLUSH to tcsetattr() as
it apparently fails to work on Solaris. After reading the
documentation again, it seems TCSAFLUSH and TCSANOW are indeed
mutually exclusive.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@826 81a1dc3b-b13d-400b-aceb-764788c761c2
* ser_win32.c (ser_open): prepend \\.\ to any COM port name, so it is
safe to be used for COM ports above 9.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@825 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500generic.c: Implement setup and teardown hooks, calling in turn
the respective hooks of the stk500v2 implementation.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@824 81a1dc3b-b13d-400b-aceb-764788c761c2
* main.c (usage): add a version number display to the default usage
message.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@823 81a1dc3b-b13d-400b-aceb-764788c761c2
support it
Do not call pgm->perform_osccal() unless it is != 0.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@822 81a1dc3b-b13d-400b-aceb-764788c761c2
* update.c (parse_op): correctly \0-terminate buf after filling
it, before it is potentially used as the source of a call to
strlen or strcpy.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@819 81a1dc3b-b13d-400b-aceb-764788c761c2
* fileio.c: Do not close the input/output stream when working on an
stdio stream.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@816 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (ATxmega256A3): new device.
* stk500v2 (stk500v2_initialize): Enable the AVRISPmkII as a
PDI-capable device for ATxmega parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@809 81a1dc3b-b13d-400b-aceb-764788c761c2
it is not useful for anything else but the CLI frontend.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@806 81a1dc3b-b13d-400b-aceb-764788c761c2
* avr.h: Remove stray semicolon.
* configure.ac: Add check for predefined types uint_t and ulong_t.
* confwin.c: Include "avrdude.h" on top to avoid empty translation
unit warning.
* ppwin.c: (Ditto.)
* ser_win32.c: (Ditto.)
* serbb_win32.c: (Ditto.)
* jtagmkII.c (jtagmkII_recv): remove unreachable "return".
* stk500.c (stk500_initialize): (Ditto.)
* par.c: Test for both, __sun__ and __sun to see whether we are
being compiled on Solaris.
* ppi.c: (Ditto.)
* stk500v2.c: Implement the DEBUG and DEBUGRECV macros in a way
that is compatible with the ISO C99 standard.
* usbtiny.c: Only typedef uint_t and ulong_t if they have not
been found already by the autoconf checks.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@804 81a1dc3b-b13d-400b-aceb-764788c761c2
connect
* configure.ac: Add checks for gethostent() and socket().
While being here, remove some old cruft left from ancient days.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@803 81a1dc3b-b13d-400b-aceb-764788c761c2
by return -1. exit(1) from a library function is not going to make
many friends upstream (in particular the day someone uses that as
part of a GUI frontend).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@800 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6749: make reading from the USBtinyISP programmer more robust
Add code to retry failed communication attempts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@799 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #22271: usb_reset in usb_libusb.c not necessary in FreeBSD 6.x
* usb_libusb.c (usbdev_close): Do not call usb_reset() on FreeBSD.
It is not necessary there.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@798 81a1dc3b-b13d-400b-aceb-764788c761c2
bug #24749: add support for '328p
* avrdude.conf.in (ATmega328P): new device support.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@796 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6261: avrdude won't use dragon/debugwire to write a file
to eeprom
* jtagmkII.c (jtagmkII_paged_write): when in debugWire mode,
implement a paged write to EEPROM as a series of byte writes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@792 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6542: paged_load fails on the MIB510 programming board
* stk500.c: Add a workaround for the different signon sequence on
MIB510 programmers.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@791 81a1dc3b-b13d-400b-aceb-764788c761c2
* usbtiny.c (usbtiny_cmd): Replace sizeof() by a fixed constant
4 for the result array, because otherwise it would take the size
of a pointer which miserably fails on 64-bit machines.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@787 81a1dc3b-b13d-400b-aceb-764788c761c2
* ppiwin.c (ppi_open): If the port parameter passed from the
-p option is neither lpt1/2/3, try interpreting it directly as
a base address.
* avrdude.1: Document the change.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@786 81a1dc3b-b13d-400b-aceb-764788c761c2
* stk500v2.c (stk500v2_chip_erase,stk500hv_chip_erase): Return
the expected 0 for success rather than a protocol-dependant
number.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@785 81a1dc3b-b13d-400b-aceb-764788c761c2
Do not erase the chip if both, -e and -n options have
been specified.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@784 81a1dc3b-b13d-400b-aceb-764788c761c2
Uncomment the correct, and delete the wrong signature for
AT90USB646/647. Alas, the datasheet has never been corrected for
years.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@782 81a1dc3b-b13d-400b-aceb-764788c761c2
mkII (or AVR Dragon) in ISP mode. The wrong set of per-programmer
private data had been allocated (stk500v2 vs. jtagmkII) which was too
small to hold the actual data.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@781 81a1dc3b-b13d-400b-aceb-764788c761c2
for Xmega programming using the JTAG ICE mkII in JTAG mode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@780 81a1dc3b-b13d-400b-aceb-764788c761c2
allow to continue with -F if it failed yet do not attempt to
perform anything on the device itself. That way, -tF could be
specified for programmers like the STK500/STK600 even without a
device connected, just in order to allow changing parameters on
the programmer itself.
* avrdude.1: Document that possible use of the -F option.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@779 81a1dc3b-b13d-400b-aceb-764788c761c2
of the number of bytes to be written which caused a malloc chunk
corruption.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@778 81a1dc3b-b13d-400b-aceb-764788c761c2
PDI mode of the STK600 is supported. Single-byte EEPROM
(and flash) updates do not work yet.
* avr.c: "boot" memory is a candidate memory region for paged
operations, besides "flash" and "eeprom".
* avrdude.conf.in: add ATxmega128A1 and ATxmega128A1revD
* avrpart.h: add the AVRPART_HAS_PDI flag (used to distinguish
ATxmega parts from classic AVRs), the nvm_base part field, and
the offset field for a memory region.
* config_gram.y: add "has_pdi", "nvm_base", and "offset"
* lexer.l: (Ditto.)
* main.c: disable auto_erase for ATxmega parts
* stk500v2.c: implement the XPROG functionality, and divert to
this for ATxmega parts
* avrdude.1: Document the changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@777 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6501: New autotools support for avrdude
* Makefile.am: add @WINDOWS_DIRS@ to SUBDIR
* bootstrap: allow for autconf-2.61 and automake-1.10, too
* configure.ac: fix @WINDOWS_DIRS@ recursion, replace
AC_PROG_CC by AM_PROG_CC_C_O, for esoteric reasons
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@774 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6074: added support for crossbow's MIB510 programmer
* avrdude.conf.in: Add entry for mib510.
* stk500.c: Add special hooks to handle the MIB510 programmer.
It mostly talks STK500v1 protocol but has a special hello and
goodbye sequence, and uses a fixed block size of 256 bytes.
* doc/avrdude.texi: Document support for mib510.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@773 81a1dc3b-b13d-400b-aceb-764788c761c2
Add check for buffermode feature, and use it if present. Can be
turned off using -x no_blockmode.
* avr910.c: Implement buffermode test and usage.
* avrdude.1: Document -x no_blockmode.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@771 81a1dc3b-b13d-400b-aceb-764788c761c2
"classic" AVRs (AT90, ATtiny, ATmega) in both,
ISP and high-voltage programming modes.
* Makefile.am: Add -lm.
* avrdude.conf.in: Add stk600, stk600pp, and stk600hvsp.
* config_gram.y: Add support for the stk600* keywords.
* lexer.l: (Ditto.)
* pgm.h: Add the "chan" parameter to set_varef().
* stk500.c: (Ditto.)
* serial.h: Add USB endpoint support to struct filedescriptor.
* stk500v2.c: Implement the meat of the STK600 support.
* stk500v2.h: Add new prototypes for stk600*() programmers.
* stk500v2_private.h: Add new constants used in the STK600.
* term.c: Add AREF channel support.
* usb_libusb.c: Automatically determine the correct write
endpoint ID, the STK600 uses 0x83 while all other tools use
0x82. Propagate the EP to use through struct filedescriptor.
* usbdevs.h: Add the STK600 USB product ID.
* tools/get-stk600-cards.xsl: XSL transformation for
targetboards.xml to obtain the list of socket and routing
card IDs, to be used in stk500v2.c (for displaying the
names).
* tools/get-stk600-devices.xsl: XSL transformation for
targetboards.xml to obtain the table of socket/routing cards
and their respective AVR device support for doc/avrdude.texi.
* avrdude.1: Document all the STK600 stuff.
* doc/avrdude.texi: Ditto. Added a new chapter for
Programmer Specific Information.
Thanks to Eirik Rasmussen from Atmel Norway for his support in
getting this code running within that short amount of time!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@768 81a1dc3b-b13d-400b-aceb-764788c761c2
and turn stderr into unbuffered output while producing the
progress report.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@765 81a1dc3b-b13d-400b-aceb-764788c761c2
definition. If present, call the setup hook immediately after finding
the respective programmer object, and schedule the teardown hook to be
called upon exit. This allows the programmer implementation to
dynamically allocate private programmer data.
avr910.c, butterfly.c, jtagmkI.c, jtagmkII.c, stk500v2.c, usbasp.c,
usbtiny.c: Convert static programmer data into dynamically allocated
data.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@764 81a1dc3b-b13d-400b-aceb-764788c761c2
the programmer backend.
jtagmkII.c: Implement the extended parameter jtagchain=
to support JTAG daisy-chains.
avrdude.1, doc/avrdude.texi: Document all of the above.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@761 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #5007: Patch for line-buffering of stdout and stderr
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@757 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6121: ISP support for the C2N232I device (serial port
bitbanging)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@755 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #6141: accept binary format immediate values
Detect a 0b prefix, and call strtoul() differently in that case.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@754 81a1dc3b-b13d-400b-aceb-764788c761c2
In ser_recv(): Drop the essentially unused variable "len", and use the
variable "read" in order to track how many bytes have just been read
in.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@753 81a1dc3b-b13d-400b-aceb-764788c761c2
Add definitions for the ATmega329P/3290P. Same as ATmega329/3290
except of the different signature.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@752 81a1dc3b-b13d-400b-aceb-764788c761c2
using default configuration file.
Uncomment the (bogus) stk500_devcode lines for the ATmega164P,
ATmega324P, ATmega644, and ATmega644P definitions. This only affects
users of STK500v1 firmware.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@750 81a1dc3b-b13d-400b-aceb-764788c761c2
"BOOT"-type code, while the standard codes are different (usually one
below).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@740 81a1dc3b-b13d-400b-aceb-764788c761c2
paged_write backend functions iff the memory area in question has
a page_size != 0.
This is supposed to fix bug #19234: avrdude-5.3.1 segfaults when
stk500v1 tries to program an ATtiny15
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@739 81a1dc3b-b13d-400b-aceb-764788c761c2
resp. Add an entry for the ATmega644P.
Fixes bug #19769: ATmega164p not recognized
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@737 81a1dc3b-b13d-400b-aceb-764788c761c2
something to the serial line. That kind of polling isn't very useful
anyway, and it seems it breaks for the Linux CP210x USB<->RS-232
bridge driver which is certainly a bug in the driver, but we can just
avoid that bug alltogether.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@736 81a1dc3b-b13d-400b-aceb-764788c761c2
ATmega640/1280/1281/2560/2561. Atmel has changed the XML
files after the initial release.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@735 81a1dc3b-b13d-400b-aceb-764788c761c2
*Problem in verbose output of previous commit. I hoped to
have all the verbose changes in a single commit, but that
won't happen...
*Main thing is fixed safemode to turn itself off when you can't
read the fuses anyway. I don't know what I was thinking when
I made it fail out of programmers that don't support fuse reading.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@733 81a1dc3b-b13d-400b-aceb-764788c761c2
include the documentation into the tarball even if the configure had been
run without the --enable-doc.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@726 81a1dc3b-b13d-400b-aceb-764788c761c2
own (duplicate) copy of it.
other files: Constify char pointers.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@725 81a1dc3b-b13d-400b-aceb-764788c761c2
list_parts() and list_programmers() functions into general list
iteration functions that call a caller-supplied callback for each
element. Implement list_parts() and list_programmers() as private
functions in main.c based on that approach.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@724 81a1dc3b-b13d-400b-aceb-764788c761c2
and link main.c against that library.
Add AC_PROG_RANLIB to configure.ac as we are building a library now.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@723 81a1dc3b-b13d-400b-aceb-764788c761c2
- Make all internal functions "static".
- Make sure each module's header and implementation file match.
- Remove all library-like functionality from main.c, so only
the actual frontend remains in main.c.
- Add C++ brackets to all header files.
That effectively leaves the various module C files as something like
an "avrdude library", with main.c being the currently only frontend
program for that library. In theory, it should be possible to write
different frontends using the same library backend functions though.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@722 81a1dc3b-b13d-400b-aceb-764788c761c2
declarations in each file by a central header file "avrdude.h".
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@721 81a1dc3b-b13d-400b-aceb-764788c761c2
and EEPROM, based on the current Atmel XML file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@720 81a1dc3b-b13d-400b-aceb-764788c761c2
and the presence of the header ddk/hidsdi.h. It now works
correctly under Cygwin and several flavours of MinGW.
* Makefile.am: Add new LIBHID pattern.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@719 81a1dc3b-b13d-400b-aceb-764788c761c2
command (which is ignored by current AVR109 bootloaders),
send the first reply from the list of supported device
codes back rather than using avrdude.conf's idea about
an AVR910 device code. Apparently, this solves disagreements
between different versions of at least the ATmega8 AVR910
device code.
Closes bug #18727: Writing flash failed
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@718 81a1dc3b-b13d-400b-aceb-764788c761c2
Change HVSP reset timing for ATtiny25/45/85 from
500 microseconds to 1 ms, matching the most recent Atmel XML
specs.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@717 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (frank-stk200): Fix syntax error.
* ser_avrdoper.c: Make #ifdef for Win32/libhid
consistent with the initial check: use the HID driver
only iff found, otherwise use libusb.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@712 81a1dc3b-b13d-400b-aceb-764788c761c2
* avrdude.conf.in (frank-stk200): New programmer added.
Closes patch #5502: one other programmer
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@706 81a1dc3b-b13d-400b-aceb-764788c761c2
patch #5507: Support for AVR-Doper USB programmer in HID mode
* configure.ac: Add hooks to detect the Win32 HID library,
as well as the existence of <ddk/hidsdi.h>.
* Makefile.am: Add new files.
* my_ddk_hidsdi.h: (New file.)
* ser_avrdoper.c: (New file.)
* serial.h: Add declaration for avrdoper_serdev.
* stk500v2.c: Add hook to divert to the AVR Doper code.
* avrdude.1: Document the AVR Doper support.
* doc/avrdude.texi: (Ditto.)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@704 81a1dc3b-b13d-400b-aceb-764788c761c2
usleep(1000000) that accidentally crept in in rev 1.19.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@702 81a1dc3b-b13d-400b-aceb-764788c761c2
value in case we had changed it.
Fixes bug #18262: JTAGMKI/JTAG1 Reset Bug
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@699 81a1dc3b-b13d-400b-aceb-764788c761c2
fallback from each programmer's paged_load() or paged_write()
method, respectively. The return value needs to be checked for
being greater or equal than 0 rather equal to 0 in order to
assume the operation has been successful.
Fixes bug #18489: avrdude is too slow (20 byte/s)
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@695 81a1dc3b-b13d-400b-aceb-764788c761c2
- declare a dummy "struct timezone" for some Win32 systems (MinGW)
- fix a few printf() argument types
- get rid off the prevailing "all filedescriptors are of type int"
attitude
The last item required a large sweep across the code, in order to
replace all "int fd"s by "struct filedescriptor *fd"s, and pass
pointers (as we cannot pass a union directly). In return, the
code is now supposed to be fully 64-bit safe, rather than relying
on a 64-bit pointer being converted to a (32-bit) int and back
to a pointer as we did previously.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@694 81a1dc3b-b13d-400b-aceb-764788c761c2
upon failure now that the upper layers won't fall back to the cmd()
method anymore in that case.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@691 81a1dc3b-b13d-400b-aceb-764788c761c2
(according to the XML files).
Add an XSL stylesheet to extract the dW
parameters from the XML files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@690 81a1dc3b-b13d-400b-aceb-764788c761c2
imposed by debugWire itself, so effectively, only flash ROM can be
read and written.
Currently, the required changes to avrdude.conf.in are only present
for the ATtiny44.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@688 81a1dc3b-b13d-400b-aceb-764788c761c2
Joerg Wunsch
Rene Liebscher
Thomas Fischl
Eric Weddington
Nils Springob
Michal Ludvig
David Hoerl
Colin O Flynn