*avrpart.h: Added prototypes for list_parts() and locate_part()
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@389 81a1dc3b-b13d-400b-aceb-764788c761c2
*avr.h: Removed prototypes for moved functions
*avrpart.h: Added prototypes for functions in avrpart.c
*Makefile.am: Added new file avrpart.c
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@388 81a1dc3b-b13d-400b-aceb-764788c761c2
available.
* avr910.c (avr910_vfy_cmd_sent): New function.
(avr910_chip_erase): Add support for chip erase.
(avr910_enter_prog_mode): New function.
(avr910_leave_prog_mode): New function.
(avr910_initialize): Add code to select device type and enter prog mode.
(avr910_close): Leave programming mode before closing serial port.
(avr910_read_sig_bytes): New function.
(avr910_initpgm): Add avr910_read_sig_bytes method to pgm initializer.
* avrdude.conf.in: Add note about deprecating devicecode.
Change all occurences of devicecode to stk500_devcode.
Add avr910_devcode to a few parts for testing.
* avrpart.h (struct avrpart): Change devicecode field to stk500_devcode.
(struct avrpart): Add avr910_devcode field.
* config_gram.y: Add K_STK500_DEVCODE and K_AVR910_DEVCODE tokens.
Generate an error if devicecode is found in the config file.
Handle parsing of avr910_devcode and stk500_devcode.
* lexer.l: Handle parsing of avr910_devcode and stk500_devcode.
* pgm.c: Initialize pgm->read_sig_bytes field.
* pgm.h: Add pgm->read_sig_bytes field.
* stk500.c: Use stk500_devcode instead of devicecode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@293 81a1dc3b-b13d-400b-aceb-764788c761c2
$HOME/.avrduderc. Entries from .avrduderc take precedence over those
from the system wide config file in ${PREFIX}/etc/avrdude.conf.
Track and display the config file name and line number when we print
out the available parts and programmers. This is useful in case
someone has overridden a definition in their .avrduderc file and is
wondering why the definition in the system wide config file is not
being used.
Remove the default programmer 'stk500' from the distributed config
file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@222 81a1dc3b-b13d-400b-aceb-764788c761c2
programming mode. Use 'retry_pulse' in the per-part specification
that can currently take values of 'reset' or 'sck', the default being
'sck' which preserves the previous behaviour. Some newer parts
indicate that /RESET should be pulsed, while older parts say to pulse
SCK.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@212 81a1dc3b-b13d-400b-aceb-764788c761c2
say whether parts support these programming modes or not. Possible
values for 'serial' are 'yes' or 'no'. Possible values for 'parallel'
are 'yes', 'no', or 'pseudo'. Add a bit mask of flags to the AVRPART
structure to capture these settings. Use these within
stk500_initialize() to set the device parameters correctly.
Defaults for 'serial' and 'parallel' are 'yes' unless specified
otherwise.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@208 81a1dc3b-b13d-400b-aceb-764788c761c2
PAGEL and BS2 signals and the disposition of the reset pin
('dedicated' or 'io').
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@202 81a1dc3b-b13d-400b-aceb-764788c761c2
supports paged reads and writes. This greatly decreases the
program/verify time from about 4.5 minutes down to about 10 seconds in
a 12K program size test case.
Print out the hardware and firmware version for the STK500 if verbose
is enabled.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk/avrdude@161 81a1dc3b-b13d-400b-aceb-764788c761c2
hinni
troth
bdean
bsd