appeared in version 2.1.0, but was changed to a 4 byte counter in
version 2.1.1. Reminded by Joerg Wunsch.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@150 81a1dc3b-b13d-400b-aceb-764788c761c2
cycle count stored at the end of EEPROM. It seems as though Atmel was
greatly conservative in claiming a 1000 count reliability for the
FLASH. I current have a part that has been reprogrammed 173330 times,
and counting.
Fix a compiler warning.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@144 81a1dc3b-b13d-400b-aceb-764788c761c2
that it is tracked no matter where the erase was initiated: command
line mode or interactive mode, without code duplicaiton.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@141 81a1dc3b-b13d-400b-aceb-764788c761c2
undergone. This utilizes the last two bytes of EEPROM to maintain a
counter that is incremented each time the part is erased.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@138 81a1dc3b-b13d-400b-aceb-764788c761c2
Display the correct memory name in an error message (previously
hardcoded).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@137 81a1dc3b-b13d-400b-aceb-764788c761c2
overwriting user-modified configs.
Add read/write instructions for all memory types for ATMEGA103,
ATMEGA128, ATMEGA16, and ATMEGA8.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@132 81a1dc3b-b13d-400b-aceb-764788c761c2
Fix setting of status LEDs under various write-fail conditions.
Add a flag to indicate that a memory type requires the device to
possibly be powered off and back on after a write to it. This is due
to a hardware problem on some Atmel devices, see:
http://www.atmel.com/atmel/acrobat/doc1280.pdf
Add greater verbosity to the part-display code when verbose>1 to
display avrprog's encoding of the defined programming instructions.
This is primarily for debugging purposes.
Part updates:
* add the AT90S4414 part
* add fuse and lock bit access instructions for the AT90S1200,
AT90S4434, and AT90S8515.
* add the pwroff_after_write flag to the fuse bits for the AT90S2333
and AT90S4433 parts
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@123 81a1dc3b-b13d-400b-aceb-764788c761c2
Make the BUFF pin a mask like VCC to allow multiple pins to be
asserted at the same time (STK200 has two buffer enable lines).
Add the STK200 programmer.
Fix EEPROM address line selection for several parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@109 81a1dc3b-b13d-400b-aceb-764788c761c2
used to make the instruction input more readable in the config file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@102 81a1dc3b-b13d-400b-aceb-764788c761c2
serial programming instructions are not very orthoganal, i.e., the
"read fuse bits" instruction on an ATMega103 is an entirely different
opcode and data format from the _same_ instruction for an ATMega163!
Thus, it becomes impossible to have a single instruction encoding
(varying the data) across the chip lines.
This set of changes allows and requires instruction encodings to be
defined on a per-part basis within the configuration file. Hopefully
I've defined the encoding scheme in a general enough way so it is
useful in describing the instruction formats for yet-to-be invented
Atmel chips. I've tried hard to make it match very closely with the
specification in Atmel's data sheets for their parts. It's a little
more verbose than what I initially hoped for, but I've tried to keep
it as concise as I could, while still remaining reasonably flexible.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@100 81a1dc3b-b13d-400b-aceb-764788c761c2
Add support for reading/writing ATMega163 lock and fuse bits.
Unfortunately, in looking at the specs for other ATMega parts, they
use entirely different instruction formats for these commands. Thus,
these routines won't work for the ATMega103, for example.
Add support for sending raw command bytes via the interactive terminal
interface. This allows one to execute any programming instruction on
the target device, whether or not avrprog supports it explicitly or
not. Thus, one can use this feature to program fuse / lock bits, or
access any other feature of a current or future device that avrprog
does not know how to do.
Add in comments, an experimental instruction format in the
configuration file. If this works out, it would allow supporting new
parts and non-orthoganal instructions across existing parts without
making avrprog code changes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@99 81a1dc3b-b13d-400b-aceb-764788c761c2
Update read/write status more frequently.
Prefix ATMega parts with an 'm'.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@95 81a1dc3b-b13d-400b-aceb-764788c761c2
Rename the poorly chosen name "bank" to "page" for page addressing.
Atmel calls it "page" in their documentation.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@91 81a1dc3b-b13d-400b-aceb-764788c761c2
checking on the memory parameters for parts that do bank addressing.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@88 81a1dc3b-b13d-400b-aceb-764788c761c2
format using a more human-readable format.
Read part descriptions from the config file now instead of hard-coding
them.
Update usage().
Cleanup unused code.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@79 81a1dc3b-b13d-400b-aceb-764788c761c2
has a 128K flash.
Due to the bank addressing required, interactive update of the flash
is not supported, though the eeprom can be updated interactively.
Both memories can be programmed via non-interactive mode.
Intel Hex Record type '04' is now generated as required for outputing
memory contents that go beyond 64K.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@78 81a1dc3b-b13d-400b-aceb-764788c761c2
assigned, otherwise, we may apply the exit specs to the wrong pins.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@71 81a1dc3b-b13d-400b-aceb-764788c761c2
might make part descriptions read in this way and we can use a
different letter for those (p). This will make the parsing easier to
distinguish between the entry types.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@69 81a1dc3b-b13d-400b-aceb-764788c761c2
file. This makes supporting other programmers much easier.
Rename AVRprog.pdf to avrprog.pdf.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@67 81a1dc3b-b13d-400b-aceb-764788c761c2
page (also updated by Joerg) to reference the schematic.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@63 81a1dc3b-b13d-400b-aceb-764788c761c2
avr.c : correct status led updates
term.c : update status leds on write, make the address and length
arguments for dump optional.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@58 81a1dc3b-b13d-400b-aceb-764788c761c2
component module. This is intended for support purposes, so that I
can tell unambiguously what version a binary out in the field is.
Additionally, display a revision timestamp along with the version
number. This also is intended for aiding in support and is the Unix
time of the latest component module. Having this, should allow me to
do a "cvs co -D timestamp avrprog" and get exactly the source of the
version that is being reported.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@55 81a1dc3b-b13d-400b-aceb-764788c761c2
bytes written. The presence of an Intel Hex address record can cause
these two number to be different; but the callers of this routine need
the former.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@54 81a1dc3b-b13d-400b-aceb-764788c761c2
fileio.c: Properly handle all the Intel Hex record types that I can
find information about.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@52 81a1dc3b-b13d-400b-aceb-764788c761c2
First pass at providing feedback via the optionally connected leds. I
don't actually have any of these attached to my programmer, so I can
only guess as whether this is toggling them on and off correctly.
Also, enable and disable the optional 74367 buffer.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@50 81a1dc3b-b13d-400b-aceb-764788c761c2
Provide hooks to support a buffered programmer, pin 6 is now used to
enable a buffer that can be used to isolate the target system from the
parallel port pins. This is important when programming the target
in-system.
Totally change the way the pin definitions are defined. Actually
set/clear pins based on the way more intuitive pin number, instead of
PPI data register, bit number combination. A table of pin data is
used so that any hardware inversion done by the parallel port is
accounted for, what you set is actually what appears at the pin.
Retain the old method for handling Vcc, however, because the hold
method is much easier to use when setting / retrieving multiple pins
simultaneously.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@49 81a1dc3b-b13d-400b-aceb-764788c761c2
prompted.
avr.c avr.h fileio.c term.c :
Change the avrpart data structure so that the typedef AVRMEM is
used as an index into an array for the sizes of the memory types
and also for pointers to buffers that represent the chip data for
that memory type. This removes a lot of conditional code of the
form:
switch (memtype) {
case AVR_FLASH :
...
}
Also, re-code avr_read_byte() and avr_write_byte() to properly
handle the flash memory type without having to tell them whether
they should program the high byte or the low byte - figure that
out from the address itself. For flash memory type, these
routines now take the actual byte address instead of the word
address. This _greatly_ simplifies many otherwise simple
operations, such a reading or writing a range of memory, by not
having to worry about whether the address starts on an odd byte
or an even byte.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@45 81a1dc3b-b13d-400b-aceb-764788c761c2
only via main() so that the exitspecs are properly applied.
When reading input data from a file, remember how many bytes were read
and write and verify only that many bytes.
Don't complain when an input file size is smaller than the memory size
we are programming. This is normal.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@44 81a1dc3b-b13d-400b-aceb-764788c761c2
record type was causing non-zero record types to be calculated
incorrectly.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@43 81a1dc3b-b13d-400b-aceb-764788c761c2
main.c : drop the giant usage text now that we have a man page.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@42 81a1dc3b-b13d-400b-aceb-764788c761c2
commands.
Fix small bug keeping 1 character command lines from being added to
the history.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@40 81a1dc3b-b13d-400b-aceb-764788c761c2
arguments, it successively dumps the next chunk of data of the same
previously specified length.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@39 81a1dc3b-b13d-400b-aceb-764788c761c2
more modular pieces.
Also, accept command abbreviations as long as they are not ambiguous.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@38 81a1dc3b-b13d-400b-aceb-764788c761c2
program exit. Default to leaving the pins in the state they were when
we found them.
Contributed by: Joerg Wunsch
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@37 81a1dc3b-b13d-400b-aceb-764788c761c2
to get the history capabilities working yet, but even so, it does
better handling of the prompt and strips newlines for us, so it's
still a win.
Add a few new commands for terminal mode: help, sig, part, erase.
Display rudimentory help using the help command.
Add some function prototypes.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@36 81a1dc3b-b13d-400b-aceb-764788c761c2
(terminal mode).
Make binary format the default for output.
Update the parts table with corrections for old values and add some
new values.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@35 81a1dc3b-b13d-400b-aceb-764788c761c2
Fix a few "may be used uninitialized" bugs found by -Wall.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@33 81a1dc3b-b13d-400b-aceb-764788c761c2
first and only write the new one if it is different.
Add -n option which is a test mode in which the chip is not actually
updated. This option does not affect writes in interactive mode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@31 81a1dc3b-b13d-400b-aceb-764788c761c2
command-line selectable option so that I don't keep forgetting and
committing it with it disabled.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@28 81a1dc3b-b13d-400b-aceb-764788c761c2
bit more option compatibility testing between -c, -i, and -o.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@27 81a1dc3b-b13d-400b-aceb-764788c761c2
parameters on startup. Use the per-chip parameters in the code
instead of hard-coded values for the 2313.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@22 81a1dc3b-b13d-400b-aceb-764788c761c2
Clean up debugging code a little, utilize fileio() instead of making
direct calls to b2ihex().
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@21 81a1dc3b-b13d-400b-aceb-764788c761c2
Re-work command line options to be more intuitive.
Support Intel Hex input and output file formats. Provide hooks to
support Motorola S-Record as well.
Add a few more part-specific parameters to the avrpart structure.
Only write the flash or eeprom if the data to be written is not 0xff.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@20 81a1dc3b-b13d-400b-aceb-764788c761c2
port to Vcc in order to supply more current.
Fix a typo on the size of the S1200's Flash.
Bring RESET low when programming is completed.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@18 81a1dc3b-b13d-400b-aceb-764788c761c2
instead of pulse.
Make all abnormal returns after the parallel port has been opened go
through a single exit point at the bottom of 'main()'.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@9 81a1dc3b-b13d-400b-aceb-764788c761c2
avrprog.c:
Add lots of comments, move getop() variable declarations to
the top of the program.
Add a typedef name to the AVR memory type and use it for
function declarations.
Add a usleep() delay in the sense loop to avoid becoming a cpu
hog.
Print out a version string so that folks know what version of
the software they are running.
Be sure and close the parallel device and the i/o file when
terminating abnormally.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@8 81a1dc3b-b13d-400b-aceb-764788c761c2
avrprog.c:
Add license.
Document the header a bit better.
Add capability to read out and display the device signature bytes.
Add capability to power the device from the parallel port.
Eliminate debug print facility.
Provide 'avr_cmd()' function.
When memory locations don't program, generate a newline so that the
information is not overwritten and lost.
Don't print out the message about needing to specify a file if the
user is not requesting an operation that requires the file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@6 81a1dc3b-b13d-400b-aceb-764788c761c2
which included commits to RCS files with non-trunk default branches.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@3 81a1dc3b-b13d-400b-aceb-764788c761c2
Brian S. Dean