file format type to 'immediate mode' where the filename is assumed to
be the memory data itself.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@318 81a1dc3b-b13d-400b-aceb-764788c761c2
specify byte values on the command line instead of via a file. This
can be good for specifying fuse bytes and eliminates the need to
create single-byte files or using interactive terminal mode for these
single-byte memories. Requested by several folks on the mailing list.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@317 81a1dc3b-b13d-400b-aceb-764788c761c2
bytes since the 'R' command returns MSB first and the internal buffer
stores LSB first.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@307 81a1dc3b-b13d-400b-aceb-764788c761c2
removed in my previous patch. Terminal mode read/writes are broken
without those methods. D'oh!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@305 81a1dc3b-b13d-400b-aceb-764788c761c2
incr supported by programmer hw, don't send addr for every byte.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@304 81a1dc3b-b13d-400b-aceb-764788c761c2
Daniel Williamson <dannyw@maconmgt.co.uk>
and
Ruwan Jayanetti <rjayanetti@sri.crossvue.com>
The resulting part definition used was actually somewhat of a merge of
the two submitted definitions.
Thanks for the contributions!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@302 81a1dc3b-b13d-400b-aceb-764788c761c2
Have avr_read_byte() call pgm->read_byte() or avr_read_byte_default().
Add avr_write_byte_default().
Have avr_write_byte() call pgm->write_byte or avr_write_byte_default().
* pgm.c: Initialize pgm->write_byte and pgm->read_byte.
* pgm.h: Add write_byte and read_byte fields to struct programmer_t.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@296 81a1dc3b-b13d-400b-aceb-764788c761c2
available.
* avr910.c (avr910_vfy_cmd_sent): New function.
(avr910_chip_erase): Add support for chip erase.
(avr910_enter_prog_mode): New function.
(avr910_leave_prog_mode): New function.
(avr910_initialize): Add code to select device type and enter prog mode.
(avr910_close): Leave programming mode before closing serial port.
(avr910_read_sig_bytes): New function.
(avr910_initpgm): Add avr910_read_sig_bytes method to pgm initializer.
* avrdude.conf.in: Add note about deprecating devicecode.
Change all occurences of devicecode to stk500_devcode.
Add avr910_devcode to a few parts for testing.
* avrpart.h (struct avrpart): Change devicecode field to stk500_devcode.
(struct avrpart): Add avr910_devcode field.
* config_gram.y: Add K_STK500_DEVCODE and K_AVR910_DEVCODE tokens.
Generate an error if devicecode is found in the config file.
Handle parsing of avr910_devcode and stk500_devcode.
* lexer.l: Handle parsing of avr910_devcode and stk500_devcode.
* pgm.c: Initialize pgm->read_sig_bytes field.
* pgm.h: Add pgm->read_sig_bytes field.
* stk500.c: Use stk500_devcode instead of devicecode.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@293 81a1dc3b-b13d-400b-aceb-764788c761c2
* config_gram.y: Add parsing of avr910 programmer.
* lexer.l: Add avr910 token.
* avr910.c: [this is still work in progress]
Add some debug output.
Add probe for programmer presense.
* main.c: Set port to default_serial if programmer type is avr910.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@292 81a1dc3b-b13d-400b-aceb-764788c761c2
Change baud from int to long to avoid a 16-bit int overflow.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@291 81a1dc3b-b13d-400b-aceb-764788c761c2
ser_posix.c files.
* avr910.c: New file (stubs for avr910 serial programmer).
* avr910.h: New file.
* ser_posix.c: New file.
* ser_win32.c: New file (just stubs for now).
* serial.h: New file.
* stk500.c: Move all the code for accessing the posix serial ports
into ser_posix. This will make a native win32 port easier and allows
the avr910 programmer to share the serial code.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@289 81a1dc3b-b13d-400b-aceb-764788c761c2
* CHANGELOG: Move contents to NEWS and remove file.
* ChangeLog: All of the changes for this year.
* ChangeLog-2001: All 2001 changes.
* ChangeLog-2002: All 2002 changes.
* Makefile.am (EXTRA_DIST): Remove CHANGELOG and and Change-200[12].
* NEWS: Moved contents of CHANGELOG file here.
* README: Add note pointing to savannah site.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@279 81a1dc3b-b13d-400b-aceb-764788c761c2
Use @option{} command for options instead of @code{}.
Merge FreeBSD and Linux platform dependent information.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@274 81a1dc3b-b13d-400b-aceb-764788c761c2
Add %post and %preun scriptlets for handling info files.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@268 81a1dc3b-b13d-400b-aceb-764788c761c2
* doc/Makefile.am: Remove extra rules that were needed to work with
automake-1.5.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@265 81a1dc3b-b13d-400b-aceb-764788c761c2
name when checking to see if we should default to the default_serial
port instead of the default_parallel port. This has us do the right
thing for the new 'avrisp' programmer.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@262 81a1dc3b-b13d-400b-aceb-764788c761c2
command be 128 bytes. This cuts 6 seconds off the programming time
for uploading a 6K file into an AT90S8515 vs the time loading the same
file using a 16 byte buffer, and the response feedback is still good.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@261 81a1dc3b-b13d-400b-aceb-764788c761c2
all on non-paged-memory parts. The problem was that the page size was
defaulting to 256 (maximum for the stk500), but the timeout for a
response from the stk500 before declaring it dead was only 0.5
seconds. But it takes much longer than 0.5 seconds to program 256
bytes, so we just weren't waiting long enough.
Fix this in two ways - increase the timeout to 5 seconds, and decrease
the page size to 16 bytes for non-paged parts. The programming time
for 16 bytes is short enough to provide the user with some feedback
that something is happening.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@260 81a1dc3b-b13d-400b-aceb-764788c761c2
itself is paged as it doesn't appear to work otherwise.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@259 81a1dc3b-b13d-400b-aceb-764788c761c2
causes some shift-reduce conflicts, but I think they are OK.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@255 81a1dc3b-b13d-400b-aceb-764788c761c2
haven't been specified in the config file for the part.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@250 81a1dc3b-b13d-400b-aceb-764788c761c2
line so future patches are obvious as to what changed.
* avrdude.spec.in: New file to support creation of binaries in rpm format.
* configure.ac (AC_OUTPUT): Add avrdude.spec.
Reorder so that Makefile is the last entry.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@240 81a1dc3b-b13d-400b-aceb-764788c761c2
* configure.ac: If $target is a windows system, build whats in windows sub dir.
* windows/Makefile.am: New file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@239 81a1dc3b-b13d-400b-aceb-764788c761c2
* Makefile.am (EXTRA_DIST): Rename avrdude.conf.sample to avrdude.conf.in.
Remove avrdude.conf and distclean-local rules.
Add install-exec-local and backup-avrdude-conf rules.
* avrdude.conf.in:
Set default_parallel to "@DEFAULT_PAR_PORT@" for autoconf expansion.
Set default_serial to "@DEFAULT_SER_PORT@" for autoconf expansion.
* configure.ac: Add call to AC_CANONICAL_{BUILD,HOST,TARGET} macros.
Set DEFAULT_PAR_PORT and DEFAULT_SER_PORT based on $host.
Add copyright header.
Define avrdude_version so AC_INIT and AM_INIT_AUTOMAKE are sure
to get the same version.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@238 81a1dc3b-b13d-400b-aceb-764788c761c2
$HOME/.avrduderc. Entries from .avrduderc take precedence over those
from the system wide config file in ${PREFIX}/etc/avrdude.conf.
Track and display the config file name and line number when we print
out the available parts and programmers. This is useful in case
someone has overridden a definition in their .avrduderc file and is
wondering why the definition in the system wide config file is not
being used.
Remove the default programmer 'stk500' from the distributed config
file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@222 81a1dc3b-b13d-400b-aceb-764788c761c2
one of the programmers to be tagged "default" within its definition.
Also, axe the notion of a compiled-in default programmer. It is
kind've pointless now that nearly all configuration comes from the
config file, thus, avrdude is not very useful without the config file,
and thus, having a programmer compiled-in offers little or no benefit.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@218 81a1dc3b-b13d-400b-aceb-764788c761c2
This adds 'default_parallel' and 'default_serial' keywords to the
grammar, which take quoted string arguments.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@214 81a1dc3b-b13d-400b-aceb-764788c761c2
programming mode. Use 'retry_pulse' in the per-part specification
that can currently take values of 'reset' or 'sck', the default being
'sck' which preserves the previous behaviour. Some newer parts
indicate that /RESET should be pulsed, while older parts say to pulse
SCK.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@212 81a1dc3b-b13d-400b-aceb-764788c761c2
say whether parts support these programming modes or not. Possible
values for 'serial' are 'yes' or 'no'. Possible values for 'parallel'
are 'yes', 'no', or 'pseudo'. Add a bit mask of flags to the AVRPART
structure to capture these settings. Use these within
stk500_initialize() to set the device parameters correctly.
Defaults for 'serial' and 'parallel' are 'yes' unless specified
otherwise.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@208 81a1dc3b-b13d-400b-aceb-764788c761c2
PAGEL and BS2 signals and the disposition of the reset pin
('dedicated' or 'io').
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@202 81a1dc3b-b13d-400b-aceb-764788c761c2
* .cvsignore: Ignore autoconf files.
* AUTHORS: New file.
* ChangeLog: New file.
* Makefile: Removed file.
* Makefile.am: New file.
* NEWS: New file.
* README: New file.
* bootstrap: New file.
* configure.ac: New file.
* avr.c: Include ac_cfg.h (generated by autoconf).
* config.c: Include ac_cfg.h.
Include config_gram.h instead of y.tab.h.
* config.h: If HAS_YYSTYPE is not defined, define YYSTYPE.
* config_gram.y: Include ac_cfg.h.
* fileio.c: Include ac_cfg.h.
* lexer.l: Include config_gram.h instead of y.tab.h.
* lists.c: Include ac_cfg.h.
* main.c: Include ac_cfg.h.
* par.c: Include ac_cfg.h.
* pgm.c: Include ac_cfg.h.
* ppi.c: Include ac_cfg.h.
* stk500.c: Include ac_cfg.h.
* term.c: Include ac_cfg.h.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@192 81a1dc3b-b13d-400b-aceb-764788c761c2
its own file par.c, leaving low level parallel port accessor routines
in ppi.c to help with portability. Change the programmer type to
'PAR' now instead of 'PPI' - 'PAR' represents the parallel port
programmer type.
Be more liberal with 'static' function declarations within the
programmer implimentation files - these functions should never be
called directly - always use the programmer function references.
There are still a few places in 'main.c' that directly reference the
parallel programmer explicitly (par_getpinmask). These should be
fixed somehow.
Axe a few unused functions.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@190 81a1dc3b-b13d-400b-aceb-764788c761c2
* ppi.c: Include system dependant parallel port interface file.
(ppi_open): Add call to ppi_claim().
(ppi_close): Add call to ppi_release().
* ppi.h: Define ppi_claim() and ppi_release() as NOPs if not previously
defined.
* stk500.c: Include inttypes header to quell compiler warning.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@184 81a1dc3b-b13d-400b-aceb-764788c761c2
care, bison does, and this is normally the way it's meant to be
anyway.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@182 81a1dc3b-b13d-400b-aceb-764788c761c2
from stk500.h - don't know how those got in there (pointed out by Ted
Roth).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@173 81a1dc3b-b13d-400b-aceb-764788c761c2
This was intended to be used for identifying code in the field for
incoming bug reports, but I've never really found it all that useful.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@171 81a1dc3b-b13d-400b-aceb-764788c761c2
This change represents a name change only. There is currently an
effort to port AVRPROG to other platforms including Linux and Windows.
Since Atmel's programmer binary that's included within their AVR
Studio software is named AVRPROG.EXE on the Windows OS, there is the
chance for confusion if we keep calling this program AVRPROG as well.
Up until now the name hasn't really been a problem since there was no
chance to confuse 'avrprog' on Unix with Atmel's AVRPROG because
Atmel's tools only run on Windows. But with the Unix 'avrprog'
possibly being ported to Windows, I felt a name change was the best
way to avoid problems.
So - from this point forward, my FreeBSD Unix program formerly known
as AVRPROG will subsequently be known as AVRDUDE (AVR Downloader/UploaDEr).
This change also represents a time when the AVRDUDE sources move from
my own private repository to a public repository. This will give
other developers a chance to port AVRDUDE to other platforms and
extend its functionality to support additional programming hardware,
etc.
So goodbye AVRPROG, welcome AVRDUDE!
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@170 81a1dc3b-b13d-400b-aceb-764788c761c2
"non-paged" parts. Take advantage of that and use the faster internal
routines of the STK500 for those parts as well.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@162 81a1dc3b-b13d-400b-aceb-764788c761c2
supports paged reads and writes. This greatly decreases the
program/verify time from about 4.5 minutes down to about 10 seconds in
a 12K program size test case.
Print out the hardware and firmware version for the STK500 if verbose
is enabled.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@161 81a1dc3b-b13d-400b-aceb-764788c761c2
that programmers other than the direct parallel port connection can be
supported.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@159 81a1dc3b-b13d-400b-aceb-764788c761c2
the 'dump <memtype>' command without any address information,
and the end of memory is reached, wrap back around to zero on
the next invocation.
CHANGELOG - describe changes
main.c - update version number
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@157 81a1dc3b-b13d-400b-aceb-764788c761c2
first pull /RESET low for a short period of time before enabling the
buffer chip. This sequence allows the AVR to be reset before the
buffer is enabled to avoid a short period of time where the AVR may be
driving the programming lines at the same time the programmer tries
to. Of course, if a buffer is being used, then the /RESET line from
the programmer needs to be directly connected to the AVR /RESET line
and not via the buffer chip.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@156 81a1dc3b-b13d-400b-aceb-764788c761c2
appeared in version 2.1.0, but was changed to a 4 byte counter in
version 2.1.1. Reminded by Joerg Wunsch.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@150 81a1dc3b-b13d-400b-aceb-764788c761c2
cycle count stored at the end of EEPROM. It seems as though Atmel was
greatly conservative in claiming a 1000 count reliability for the
FLASH. I current have a part that has been reprogrammed 173330 times,
and counting.
Fix a compiler warning.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@144 81a1dc3b-b13d-400b-aceb-764788c761c2
that it is tracked no matter where the erase was initiated: command
line mode or interactive mode, without code duplicaiton.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@141 81a1dc3b-b13d-400b-aceb-764788c761c2
undergone. This utilizes the last two bytes of EEPROM to maintain a
counter that is incremented each time the part is erased.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@138 81a1dc3b-b13d-400b-aceb-764788c761c2
Display the correct memory name in an error message (previously
hardcoded).
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@137 81a1dc3b-b13d-400b-aceb-764788c761c2
overwriting user-modified configs.
Add read/write instructions for all memory types for ATMEGA103,
ATMEGA128, ATMEGA16, and ATMEGA8.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@132 81a1dc3b-b13d-400b-aceb-764788c761c2
Fix setting of status LEDs under various write-fail conditions.
Add a flag to indicate that a memory type requires the device to
possibly be powered off and back on after a write to it. This is due
to a hardware problem on some Atmel devices, see:
http://www.atmel.com/atmel/acrobat/doc1280.pdf
Add greater verbosity to the part-display code when verbose>1 to
display avrprog's encoding of the defined programming instructions.
This is primarily for debugging purposes.
Part updates:
* add the AT90S4414 part
* add fuse and lock bit access instructions for the AT90S1200,
AT90S4434, and AT90S8515.
* add the pwroff_after_write flag to the fuse bits for the AT90S2333
and AT90S4433 parts
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@123 81a1dc3b-b13d-400b-aceb-764788c761c2
Make the BUFF pin a mask like VCC to allow multiple pins to be
asserted at the same time (STK200 has two buffer enable lines).
Add the STK200 programmer.
Fix EEPROM address line selection for several parts.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@109 81a1dc3b-b13d-400b-aceb-764788c761c2
used to make the instruction input more readable in the config file.
git-svn-id: svn://svn.savannah.nongnu.org/avrdude/trunk@102 81a1dc3b-b13d-400b-aceb-764788c761c2
Brian S. Dean
Theodore A. Roth
Eric Weddington
Joerg Wunsch