Merge branch 'avrdudes:main' into terminal

NEWS

@@ -32,8 +32,12 @@ Changes since version 7.0:
     - Replace internal knowledge in jtag3.c by a public API #996
     - JTAG3 UPDI EEPROM fix #1013
     - Treat x bits in .conf SPI commands as 0 #943
-    - Fix avrftdi support for ATmega2560 et al #474
+    - Fix avrftdi support for ATmega2560 et al #998
-    - Fix avrdude.conf timings for ATmega328PB and other parts #976
+    - Fix avrdude.conf timings for ATmega328PB and other parts #1001
+    - Fix PICKit2 ATmega2560 flash paged flash read #1023
+    - Fix ft245r paged read for ATmega2560 et al #1018
+    - Add option -A that supresses trailing 0xff optimisation
+      and automatically do so for -c arduino #936
 
   * Internals:
 

src/arduino.c

@@ -130,4 +130,6 @@ void arduino_initpgm(PROGRAMMER * pgm)
   pgm->read_sig_bytes = arduino_read_sig_bytes;
   pgm->open = arduino_open;
   pgm->close = arduino_close;
+
+  disable_trailing_ff_removal(); /* so that arduino bootloader can ignore chip erase */
 }

src/avr.c

@@ -278,10 +278,28 @@ int avr_read_byte_default(PROGRAMMER * pgm, AVRPART * p, AVRMEM * mem,
  * value. This is useful for determining where to stop when dealing
  * with "flash" memory, since writing 0xff to flash is typically a
  * no-op. Always return an even number since flash is word addressed.
+ * Only apply this optimisation on flash-type memory.
  */
 int avr_mem_hiaddr(AVRMEM * mem)
 {
   int i, n;
+  static int disableffopt;
+
+  /* calling once with NULL disables any future trailing-0xff optimisation */
+  if(!mem) {
+    disableffopt = 1;
+    return 0;
+  }
+
+  if(disableffopt)
+    return mem->size;
+
+  /* if the memory is not a flash-type memory do not remove trailing 0xff */
+  if(strcasecmp(mem->desc, "flash") &&
+     strcasecmp(mem->desc, "application") &&
+     strcasecmp(mem->desc, "apptable") &&
+     strcasecmp(mem->desc, "boot"))
+    return mem->size;
 
   /* return the highest non-0xff address regardless of how much
      memory was read */
@@ -416,15 +434,8 @@ int avr_read(PROGRAMMER * pgm, AVRPART * p, char * memtype,
       nread++;
       report_progress(nread, npages, NULL);
     }
-    if (!failure) {
+    if (!failure)
-      if (strcasecmp(mem->desc, "flash") == 0 ||
-          strcasecmp(mem->desc, "application") == 0 ||
-          strcasecmp(mem->desc, "apptable") == 0 ||
-          strcasecmp(mem->desc, "boot") == 0)
       return avr_mem_hiaddr(mem);
-      else
-        return mem->size;
-    }
     /* else: fall back to byte-at-a-time write, for historical reasons */
   }
 
@@ -454,13 +465,7 @@ int avr_read(PROGRAMMER * pgm, AVRPART * p, char * memtype,
     report_progress(i, mem->size, NULL);
   }
 
-  if (strcasecmp(mem->desc, "flash") == 0 ||
-      strcasecmp(mem->desc, "application") == 0 ||
-      strcasecmp(mem->desc, "apptable") == 0 ||
-      strcasecmp(mem->desc, "boot") == 0)
   return avr_mem_hiaddr(mem);
-  else
-    return i;
 }
 
 

src/avrdude.1

@@ -18,7 +18,7 @@
 .\"
 .\" $Id$
 .\"
-.Dd November 22, 2021
+.Dd July 12, 2022
 .Os
 .Dt AVRDUDE 1
 .Sh NAME
@@ -31,6 +31,7 @@
 .Op Fl B Ar bitclock
 .Op Fl c Ar programmer-id
 .Op Fl C Ar config-file
+.Op Fl A
 .Op Fl D
 .Op Fl e
 .Oo Fl E Ar exitspec Ns
@@ -102,7 +103,7 @@ available (like almost all embedded Linux boards) you can do without
 any additional hardware - just connect them to the MOSI, MISO, RESET 
 and SCK pins on the AVR and use the linuxgpio programmer type. It bitbangs
 the lines using the Linux sysfs GPIO interface. Of course, care should
-be taken about voltage level compatibility. Also, although not strictrly 
+be taken about voltage level compatibility. Also, although not strictly
 required, it is strongly advisable to protect the GPIO pins from 
 overcurrent situations in some way. The simplest would be to just put
 some resistors in series or better yet use a 3-state buffer driver like
@@ -253,7 +254,7 @@ The Teensy bootloader is supported for all AVR boards.
 As the bootloader does not support reading from flash memory,
 use the
 .Fl V
-option to prevent AVRDUDE from verifing the flash memory.
+option to prevent AVRDUDE from verifying the flash memory.
 See the section on
 .Em extended parameters
 for Teensy specific options.
@@ -376,6 +377,20 @@ files. This can be used to add entries to the configuration
 without patching your system wide configuration file. It can be used
 several times, the files are read in same order as given on the command
 line.
+.It Fl A
+Disable the automatic removal of trailing-0xFF sequences in file
+input that is to be programmed to flash and in AVR reads from
+flash memory. Normally, trailing 0xFFs can be discarded, as flash
+programming requires the memory be erased to 0xFF beforehand.
+.Fl A
+should be used when the programmer hardware, or bootloader
+software for that matter, does not carry out chip erase and
+instead handles the memory erase on a page level. The popular
+Arduino bootloader exhibits this behaviour; for this reason
+.Fl A
+is engaged by default when specifying
+. Fl c
+arduino.
 .It Fl D
 Disable auto erase for flash.  When the
 .Fl U
@@ -389,6 +404,10 @@ use page erase before writing each page so no explicit chip erase
 is required.
 Note however that any page not affected by the current operation
 will retain its previous contents.
+Setting
+.Fl D
+implies
+.Fl A.
 .It Fl e
 Causes a chip erase to be executed.  This will reset the contents of the
 flash ROM and EEPROM to the value

src/doc/avrdude.texi

@@ -321,13 +321,13 @@ via a serial link (@url{https://github.com/ElTangas/jtag2updi}).
 
 The Micronucleus bootloader is supported for both protocol version V1
 and V2. As the bootloader does not support reading from flash memory,
-use the @code{-V} option to prevent AVRDUDE from verifing the flash memory.
+use the @code{-V} option to prevent AVRDUDE from verifying the flash memory.
 See the section on @emph{extended parameters}
 below for Micronucleus specific options.
 
 The Teensy bootloader is supported for all AVR boards.
 As the bootloader does not support reading from flash memory,
-use the @code{-V} option to prevent AVRDUDE from verifing the flash memory.
+use the @code{-V} option to prevent AVRDUDE from verifying the flash memory.
 See the section on @emph{extended parameters}
 below for Teensy specific options.
 
@@ -495,6 +495,16 @@ without patching your system wide configuration file. It can be used
 several times, the files are read in same order as given on the command 
 line.
 
+@item -A
+Disable the automatic removal of trailing-0xFF sequences in file
+input that is to be programmed to flash and in AVR reads from
+flash memory. Normally, trailing 0xFFs can be discarded, as flash
+programming requires the memory be erased to 0xFF beforehand. -A
+should be used when the programmer hardware, or bootloader
+software for that matter, does not carry out chip erase and
+instead handles the memory erase on a page level. The popular
+Arduino bootloader exhibits this behaviour; for this reason -A is
+engaged by default when specifying -c arduino.
 
 @item -D
 Disable auto erase for flash.  When the -U option with flash memory is 
@@ -506,6 +516,7 @@ use page erase before writing each page so no explicit chip erase
 is required.
 Note however that any page not affected by the current operation
 will retain its previous contents.
+Setting -D implies -A.
 
 @item -e
 Causes a chip erase to be executed.  This will reset the contents of the

src/fileio.c

@@ -1446,16 +1446,17 @@ static int fmt_autodetect(char * fname)
 
 
 
-int fileio(int op, char * filename, FILEFMT format, 
+int fileio(int oprwv, char * filename, FILEFMT format,
              struct avrpart * p, char * memtype, int size)
 {
-  int rc;
+  int op, rc;
   FILE * f;
   char * fname;
   struct fioparms fio;
   AVRMEM * mem;
   int using_stdio;
 
+  op = oprwv == FIO_READ_FOR_VERIFY? FIO_READ: oprwv;
   mem = avr_locate_mem(p, memtype);
   if (mem == NULL) {
     avrdude_message(MSG_INFO, "fileio(): memory type \"%s\" not configured for device \"%s\"\n",
@@ -1585,18 +1586,14 @@ int fileio(int op, char * filename, FILEFMT format,
       return -1;
   }
 
-  if (rc > 0) {
+  /* on reading flash other than for verify set the size to location of highest non-0xff byte */
-    if ((op == FIO_READ) && (strcasecmp(mem->desc, "flash") == 0 ||
+  if (rc > 0 && oprwv == FIO_READ) {
-                             strcasecmp(mem->desc, "application") == 0 ||
+    int hiaddr = avr_mem_hiaddr(mem);
-                             strcasecmp(mem->desc, "apptable") == 0 ||
+
-                             strcasecmp(mem->desc, "boot") == 0)) {
+    if(hiaddr < rc)             /* if trailing-0xff not disabled */
-      /*
+      rc = hiaddr;
-       * if we are reading flash, just mark the size as being the
-       * highest non-0xff byte
-       */
-      rc = avr_mem_hiaddr(mem);
-    }
   }
+
   if (format != FMT_IMM && !using_stdio) {
     fclose(f);
   }

src/ft245r.c

@@ -108,9 +108,9 @@ void ft245r_initpgm(PROGRAMMER * pgm) {
 #else
 
 #define FT245R_CYCLES          2
-#define FT245R_FRAGMENT_SIZE  512
+#define FT245R_CMD_SIZE       (4 * 8*FT245R_CYCLES)
+#define FT245R_FRAGMENT_SIZE  (8 * FT245R_CMD_SIZE)
 #define REQ_OUTSTANDINGS      10
-//#define USE_INLINE_WRITE_PAGE
 
 #define FT245R_DEBUG	0
 /*
@@ -992,39 +992,17 @@ static void ft245r_display(PROGRAMMER * pgm, const char * p) {
     pgm_display_generic_mask(pgm, p, SHOW_ALL_PINS);
 }
 
+
 static int ft245r_paged_write_gen(PROGRAMMER *pgm, AVRPART *p, AVRMEM *m,
-                                  unsigned int page_size, unsigned int addr,
+             unsigned int page_size, unsigned int addr, unsigned int n_bytes) {
-                                  unsigned int n_bytes) {
-    unsigned long i, pa;
-    int rc;
 
-    for (i=0; i<n_bytes; i++, addr++) {
+    for(int i=0; i < (int) n_bytes; i++, addr++)
-        rc = avr_write_byte_default(pgm, p, m, addr, m->buf[addr]);
+        if(avr_write_byte_default(pgm, p, m, addr, m->buf[addr]) != 0)
-        if (rc != 0) {
             return -2;
+
+    return n_bytes;
 }
 
-        if (m->paged) {
-            // Can this piece of code ever be activated?? Do AVRs exist that
-            // have paged non-flash memories? -- REW
-            // XXX Untested code below.
-            /*
-             * check to see if it is time to flush the page with a page
-             * write
-             */
-
-            if (((addr % m->page_size) == m->page_size-1) || (i == n_bytes-1)) {
-                pa = addr - (addr % m->page_size);
-
-                rc = avr_write_page(pgm, p, m, pa);
-                if (rc != 0) {
-                    return -2;
-                }
-            }
-        }
-    }
-    return i;
-}
 
 static struct ft245r_request {
     int addr;
@@ -1081,179 +1059,186 @@ static int do_request(PROGRAMMER * pgm, AVRMEM *m) {
     return 1;
 }
 
+
 static int ft245r_paged_write_flash(PROGRAMMER *pgm, AVRPART *p, AVRMEM *m,
-                                    int page_size, int addr, int n_bytes) {
+             unsigned int page_size, unsigned int addr, unsigned int n_bytes) {
-    unsigned int    i,j;
-    int addr_save,buf_pos,do_page_write,req_count;
-    unsigned char buf[FT245R_FRAGMENT_SIZE+1+128];
 
-    req_count = 0;
+    int i, j, addr_save, buf_pos, req_count, do_page_write;
-    for (i=0; i<n_bytes; ) {
+    unsigned char buf[FT245R_FRAGMENT_SIZE+1];
-        addr_save = addr;
-        buf_pos = 0;
-        do_page_write = 0;
-        for (j=0; j< FT245R_FRAGMENT_SIZE/8/FT245R_CYCLES/4; j++) {
-            buf_pos += set_data(pgm, buf+buf_pos, (addr & 1)?0x48:0x40 );
-            buf_pos += set_data(pgm, buf+buf_pos, (addr >> 9) & 0xff );
-            buf_pos += set_data(pgm, buf+buf_pos, (addr >> 1) & 0xff );
-            buf_pos += set_data(pgm, buf+buf_pos, m->buf[addr]);
-            addr ++;
-            i++;
-            if ( (m->paged) &&
-                    (((i % m->page_size) == 0) || (i == n_bytes))) {
-                do_page_write = 1;
-                break;
-            }
-        }
-#if defined(USE_INLINE_WRITE_PAGE)
-        if (do_page_write) {
-            int addr_wk = addr_save - (addr_save % m->page_size);
-            /* If this device has a "load extended address" command, issue it. */
-            if (m->op[AVR_OP_LOAD_EXT_ADDR]) {
     unsigned char cmd[4];
-                OPCODE *lext = m->op[AVR_OP_LOAD_EXT_ADDR];
 
-                memset(cmd, 0, 4);
+    if(m->op[AVR_OP_LOADPAGE_LO] == NULL || m->op[AVR_OP_LOADPAGE_HI] == NULL) {
-                avr_set_bits(lext, cmd);
+        avrdude_message(MSG_INFO, "AVR_OP_LOADPAGE_HI/LO command not defined for %s\n", p->desc);
-                avr_set_addr(lext, cmd, addr_wk/2);
+        return -1;
-                buf_pos += set_data(pgm, buf+buf_pos, cmd[0]);
-                buf_pos += set_data(pgm, buf+buf_pos, cmd[1]);
-                buf_pos += set_data(pgm, buf+buf_pos, cmd[2]);
-                buf_pos += set_data(pgm, buf+buf_pos, cmd[3]);
     }
-            buf_pos += set_data(pgm, buf+buf_pos, 0x4C); /* Issue Page Write */
+
-            buf_pos += set_data(pgm, buf+buf_pos,(addr_wk >> 9) & 0xff);
+    do_page_write = req_count = i = j = buf_pos = 0;
-            buf_pos += set_data(pgm, buf+buf_pos,(addr_wk >> 1) & 0xff);
+    addr_save = addr;
-            buf_pos += set_data(pgm, buf+buf_pos, 0);
+    while(i < (int) n_bytes) {
-        }
+        int spi = addr&1? AVR_OP_LOADPAGE_HI: AVR_OP_LOADPAGE_LO;
-#endif
+
+        // put the SPI loadpage command as FT245R_CMD_SIZE bytes into buffer
+        memset(cmd, 0, sizeof cmd);
+        avr_set_bits(m->op[spi], cmd);
+        avr_set_addr(m->op[spi], cmd, addr/2);
+        avr_set_input(m->op[spi], cmd, m->buf[addr]);
+        for(int k=0; k<sizeof cmd; k++)
+           buf_pos += set_data(pgm, buf+buf_pos, cmd[k]);
+
+        i++; j++; addr++;
+
+        if(m->paged && (i%m->page_size == 0 || i >= (int) n_bytes))
+            do_page_write = 1;
+
+        // page boundary, finished or buffer exhausted? queue up requests
+        if(do_page_write || i >= (int) n_bytes || j >= FT245R_FRAGMENT_SIZE/FT245R_CMD_SIZE) {
             if(i >= n_bytes) {
-            ft245r_out = SET_BITS_0(ft245r_out,pgm,PIN_AVR_SCK,0); // sck down
+                ft245r_out = SET_BITS_0(ft245r_out, pgm, PIN_AVR_SCK, 0); // SCK down
                 buf[buf_pos++] = ft245r_out;
-        }
+            } else {
-        else {
+                // stretch sequence to allow correct readout, see extract_data()
-            /* stretch sequence to allow correct readout, see extract_data() */
                 buf[buf_pos] = buf[buf_pos - 1];
                 buf_pos++;
             }
             ft245r_send(pgm, buf, buf_pos);
             put_request(addr_save, buf_pos, 0);
-        //ft245r_sync(pgm);
+
-#if 0
+            if(++req_count > REQ_OUTSTANDINGS)
-        avrdude_message(MSG_INFO, "send addr 0x%04x bufsize %d [%02x %02x] page_write %d\n",
-                addr_save,buf_pos,
-                extract_data_out(pgm, buf , (0*4 + 3) ),
-                extract_data_out(pgm, buf , (1*4 + 3) ),
-                do_page_write);
-#endif
-        req_count++;
-        if (req_count > REQ_OUTSTANDINGS)
                 do_request(pgm, m);
+
             if(do_page_write) {
-#if defined(USE_INLINE_WRITE_PAGE)
                 while(do_request(pgm, m))
-                ;
+                    continue;
-            ft245r_usleep(pgm, m->max_write_delay);
+                if(avr_write_page(pgm, p, m, addr_save - (addr_save % m->page_size)) != 0)
-#else
-            int addr_wk = addr_save - (addr_save % m->page_size);
-            int rc;
-            while (do_request(pgm, m))
-                ;
-            rc = avr_write_page(pgm, p, m, addr_wk);
-            if (rc != 0) {
                     return -2;
+                do_page_write = req_count = 0;
             }
-#endif
+
-            req_count = 0;
+            // reset buffer variables
+            j = buf_pos = 0;
+            addr_save = addr;
         }
     }
+
     while(do_request(pgm, m))
-        ;
+        continue;
-    return i;
+
+    return n_bytes;
 }
 
 
 static int ft245r_paged_write(PROGRAMMER * pgm, AVRPART * p, AVRMEM * m,
             unsigned int page_size, unsigned int addr, unsigned int n_bytes) {
-    if (strcmp(m->desc, "flash") == 0) {
+
+    if(!n_bytes)
+        return 0;
+
+    if(strcmp(m->desc, "flash") == 0)
         return ft245r_paged_write_flash(pgm, p, m, page_size, addr, n_bytes);
-    } else if (strcmp(m->desc, "eeprom") == 0) {
+
+    if(strcmp(m->desc, "eeprom") == 0)
         return ft245r_paged_write_gen(pgm, p, m, page_size, addr, n_bytes);
-    } else {
+
     return -2;
 }
-}
 
 static int ft245r_paged_load_gen(PROGRAMMER *pgm, AVRPART *p, AVRMEM *m,
-                                 unsigned int page_size, unsigned int addr,
+             unsigned int page_size, unsigned int addr, unsigned int n_bytes) {
-                                 int n_bytes) {
-    unsigned char    rbyte;
-    unsigned long    i;
-    int rc;
 
-    for (i=0; i<n_bytes; i++) {
+    for(int i=0; i < (int) n_bytes; i++) {
-        rc = avr_read_byte_default(pgm, p, m, i+addr, &rbyte);
+        unsigned char rbyte;
-        if (rc != 0) {
+
+        if(avr_read_byte_default(pgm, p, m, addr+i, &rbyte) != 0)
             return -2;
+
+        m->buf[addr+i] = rbyte;
     }
-        m->buf[i+addr] = rbyte;
+
-    }
     return 0;
 }
 
-static int ft245r_paged_load_flash(PROGRAMMER * pgm, AVRPART * p, AVRMEM * m,
-                                   unsigned int page_size, unsigned int addr,
-                                   unsigned int n_bytes) {
-    unsigned long    i,j,n;
-    int addr_save,buf_pos;
-    int req_count = 0;
-    unsigned char buf[FT245R_FRAGMENT_SIZE+1];
 
-    for (i=0; i<n_bytes; ) {
+static int ft245r_paged_load_flash(PROGRAMMER *pgm, AVRPART *p, AVRMEM *m,
+            unsigned int page_size, unsigned int addr, unsigned int n_bytes) {
+
+    int i, j, addr_save, buf_pos, req_count;
+    unsigned char buf[FT245R_FRAGMENT_SIZE+1];
+    unsigned char cmd[4];
+
+    if(m->op[AVR_OP_READ_LO] == NULL || m->op[AVR_OP_READ_HI] == NULL) {
+        avrdude_message(MSG_INFO, "AVR_OP_READ_HI/LO command not defined for %s\n", p->desc);
+        return -1;
+    }
+
+    // always called with addr at page boundary, and n_bytes == m->page_size;
+    // hence, OK to prepend load extended address command (at most) once
+    if(m->op[AVR_OP_LOAD_EXT_ADDR]) {
+        memset(cmd, 0, sizeof cmd);
+	avr_set_bits(m->op[AVR_OP_LOAD_EXT_ADDR], cmd);
+	avr_set_addr(m->op[AVR_OP_LOAD_EXT_ADDR], cmd, addr/2);
+
         buf_pos = 0;
+        for(int k=0; k<sizeof cmd; k++)
+            buf_pos += set_data(pgm, buf+buf_pos, cmd[k]);
+        ft245r_send_and_discard(pgm, buf, buf_pos);
+    }
+
+    req_count = i = j = buf_pos = 0;
     addr_save = addr;
-        for (j=0; j< FT245R_FRAGMENT_SIZE/8/FT245R_CYCLES/4; j++) {
+    while(i < (int) n_bytes) {
-            if (i >= n_bytes) break;
+        int spi = addr&1? AVR_OP_READ_HI: AVR_OP_READ_LO;
-            buf_pos += set_data(pgm, buf+buf_pos, (addr & 1)?0x28:0x20 );
+
-            buf_pos += set_data(pgm, buf+buf_pos, (addr >> 9) & 0xff );
+        // put the SPI read command as FT245R_CMD_SIZE bytes into buffer
-            buf_pos += set_data(pgm, buf+buf_pos, (addr >> 1) & 0xff );
+        memset(cmd, 0, sizeof cmd);
-            buf_pos += set_data(pgm, buf+buf_pos, 0);
+        avr_set_bits(m->op[spi], cmd);
-            addr ++;
+        avr_set_addr(m->op[spi], cmd, addr/2);
-            i++;
+        for(int k=0; k<sizeof cmd; k++)
-        }
+           buf_pos += set_data(pgm, buf+buf_pos, cmd[k]);
-        if (i >= n_bytes) {
+
-            ft245r_out = SET_BITS_0(ft245r_out,pgm,PIN_AVR_SCK,0); // sck down
+        i++; j++; addr++;
+
+        // finished or buffer exhausted? queue up requests
+        if(i >= (int) n_bytes || j >= FT245R_FRAGMENT_SIZE/FT245R_CMD_SIZE) {
+            if(i >= (int) n_bytes) {
+                ft245r_out = SET_BITS_0(ft245r_out, pgm, PIN_AVR_SCK, 0); // SCK down
                 buf[buf_pos++] = ft245r_out;
-        }
+            } else {
-        else {
+                // stretch sequence to allow correct readout, see extract_data()
-            /* stretch sequence to allow correct readout, see extract_data() */
                 buf[buf_pos] = buf[buf_pos - 1];
                 buf_pos++;
             }
-        n = j;
             ft245r_send(pgm, buf, buf_pos);
-        put_request(addr_save, buf_pos, n);
+            put_request(addr_save, buf_pos, j);
-        req_count++;
+
-        if (req_count > REQ_OUTSTANDINGS)
+            if(++req_count > REQ_OUTSTANDINGS)
                 do_request(pgm, m);
 
+            // reset buffer variables
+            j = buf_pos = 0;
+            addr_save = addr;
         }
+    }
+
     while(do_request(pgm, m))
-        ;
+        continue;
+
     return 0;
 }
 
 static int ft245r_paged_load(PROGRAMMER *pgm, AVRPART *p, AVRMEM *m,
-                             unsigned int page_size, unsigned int addr,
+             unsigned int page_size, unsigned int addr, unsigned int n_bytes) {
-                             unsigned int n_bytes) {
+
-    if (strcmp(m->desc, "flash") == 0) {
+    if(!n_bytes)
+        return 0;
+
+    if(strcmp(m->desc, "flash") == 0)
         return ft245r_paged_load_flash(pgm, p, m, page_size, addr, n_bytes);
-    } else if (strcmp(m->desc, "eeprom") == 0) {
+
+   if(strcmp(m->desc, "eeprom") == 0)
         return ft245r_paged_load_gen(pgm, p, m, page_size, addr, n_bytes);
-    } else {
+
    return -2;
 }
-}
 
 void ft245r_initpgm(PROGRAMMER * pgm) {
     strcpy(pgm->type, "ftdi_syncbb");

src/libavrdude.h

@@ -797,6 +797,7 @@ int avr_get_cycle_count(PROGRAMMER * pgm, AVRPART * p, int * cycles);
 
 int avr_put_cycle_count(PROGRAMMER * pgm, AVRPART * p, int cycles);
 
+#define disable_trailing_ff_removal() avr_mem_hiaddr(NULL)
 int avr_mem_hiaddr(AVRMEM * mem);
 
 int avr_chip_erase(PROGRAMMER * pgm, AVRPART * p);
@@ -835,7 +836,8 @@ struct fioparms {
 
 enum {
   FIO_READ,
-  FIO_WRITE
+  FIO_WRITE,
+  FIO_READ_FOR_VERIFY,
 };
 
 #ifdef __cplusplus
@@ -844,7 +846,7 @@ extern "C" {
 
 char * fmtstr(FILEFMT format);
 
-int fileio(int op, char * filename, FILEFMT format,
+int fileio(int oprwv, char * filename, FILEFMT format,
            struct avrpart * p, char * memtype, int size);
 
 #ifdef __cplusplus

src/main.c

@@ -110,7 +110,8 @@ static void usage(void)
  "  -B <bitclock>              Specify JTAG/STK500v2 bit clock period (us).\n"
  "  -C <config-file>           Specify location of configuration file.\n"
  "  -c <programmer>            Specify programmer type.\n"
- "  -D                         Disable auto erase for flash memory\n"
+ "  -A                         Disable trailing-0xff removal from file and AVR read.\n"
+ "  -D                         Disable auto erase for flash memory; implies -A.\n"
  "  -i <delay>                 ISP Clock Delay [in microseconds]\n"
  "  -P <port>                  Specify connection port.\n"
  "  -F                         Override invalid signature check.\n"
@@ -442,7 +443,7 @@ int main(int argc, char * argv [])
   /*
    * process command line arguments
    */
-  while ((ch = getopt(argc,argv,"?b:B:c:C:DeE:Fi:l:np:OP:qstU:uvVx:yY:")) != -1) {
+  while ((ch = getopt(argc,argv,"?Ab:B:c:C:DeE:Fi:l:np:OP:qstU:uvVx:yY:")) != -1) {
 
     switch (ch) {
       case 'b': /* override default programmer baud rate */
@@ -528,6 +529,10 @@ int main(int argc, char * argv [])
 
       case 'D': /* disable auto erase */
         uflags &= ~UF_AUTO_ERASE;
+        /* fall through */
+
+      case 'A': /* explicit disabling of trailing-0xff removal */
+        disable_trailing_ff_removal();
         break;
 
       case 'e': /* perform a chip erase */

src/pickit2.c

@@ -491,18 +491,15 @@ static int  pickit2_paged_load(PROGRAMMER * pgm, AVRPART * p, AVRMEM * mem,
 
     pgm->pgm_led(pgm, ON);
 
-    for (addr_base = addr; addr_base < max_addr; )
+    if (lext) {
-    {
-        if ((addr_base == 0 || (addr_base % /*ext_address_boundary*/ 65536) == 0)
-                && lext != NULL)
-        {
        memset(cmd, 0, sizeof(cmd));
-
        avr_set_bits(lext, cmd);
-            avr_set_addr(lext, cmd, addr_base);
+       avr_set_addr(lext, cmd, addr/2);
        pgm->cmd(pgm, cmd, res);
     }
 
+    for (addr_base = addr; addr_base < max_addr; )
+    {
         // bytes to send in the next packet -- not necessary as pickit2_spi() handles breaking up
         // the data into packets -- but we need to keep transfers frequent so that we can update the
         // status indicator bar

src/update.c

@@ -341,7 +341,7 @@ int do_op(PROGRAMMER * pgm, struct avrpart * p, UPDATE * upd, enum updateflags f
             progname, mem->desc, alias_mem_desc, upd->filename);
     }
 
-    rc = fileio(FIO_READ, upd->filename, upd->format, p, upd->memtype, -1);
+    rc = fileio(FIO_READ_FOR_VERIFY, upd->filename, upd->format, p, upd->memtype, -1);
     if (rc < 0) {
       avrdude_message(MSG_INFO, "%s: read from file '%s' failed\n",
               progname, upd->filename);