avrdude/CHANGELOG

$Id$

Approximate change log for AVRDUDE by version

----------------------------------------------------------------------

Version 3.1.0

  * This change represents a name change only.  There is currently an
    effort to port AVRPROG to other platforms including Linux and
    Windows.  Since Atmel's programmer binary that's included within
    their AVR Studio software is named AVRPROG.EXE on the Windows OS,
    there is the chance for confusion if we keep calling this program
    AVRPROG as well.  Up until now the name hasn't really been a
    problem since there was no chance to confuse 'avrprog' on Unix
    with Atmel's AVRPROG because Atmel's tools only run on Windows.
    But with the Unix 'avrprog' possibly being ported to Windows, I
    felt a name change was the best way to avoid problems.

    So - from this point forward, my FreeBSD Unix program formerly
    known as AVRPROG will subsequently be known as AVRDUDE (AVR
    Downloader/UploaDEr).

    This change also represents a time when the AVRDUDE sources move
    from my own private repository to a public repository.  This will
    give other developers a chance to port AVRDUDE to other platforms
    and extend its functionality to support additional programming
    hardware, etc.

    So goodbye AVRPROG, welcome AVRDUDE!

Version 3.0.0

  * Rewrite parts of the code to make it easy to support other types
    of programmers besides the directly connected parallel port
    programmer (PPI).

  * Add support for Atmel's STK500 programmer/development board.  The
    STK500's "paged mode" read/write is supported which makes this
    programmer very fast.  This is sorely needed on parts with large
    memories such as the ATmega128.  My 12K test program burns in
    about 5 seconds, add another 5 to read it back out for
    verification.


Version 2.1.5:

  * When getting ready to initiate communications with the AVR device,
    first pull /RESET low for a short period of time before enabling
    the buffer chip.  This sequence allows the AVR to be reset before
    the buffer is enabled to avoid a short period of time where the
    AVR may be driving the programming lines at the same time the
    programmer tries to.  Of course, if a buffer is being used, then
    the /RESET line from the programmer needs to be directly connected
    to the AVR /RESET line and not via the buffer chip.

    Feature contributed by Rick C. Petty <rick@KIWI-Computer.com>.

  * When in interactive terminal mode and dumping memory using the
    'dump <memtype>' command without any address information, and the
    end of memory is reached, wrap back around to zero on the next
    invocation.


Version 2.1.4:

  * Fix -Y option.


Version 2.1.3:

  * Be backward compatible when reading 2-byte rewrite cycle counters
    as written by avrprog version 2.1.0.  Version 2.1.1 changed over
    to a 4-byte counter, which caused avrprog versions 2.1.1 and 2.1.2
    to report a negative count for parts that were initialized using
    version 2.1.0.  Thanks to Joerg Wunsch for noticing this.


Version 2.1.2:

  * Add '-V' option to disable automatic verify check with uploading
    data.


Version 2.1.1:

  * Fix ATmega128 instruction sequences for reading fuse bits -
    contributed by Joerg Wunsch.

  * Modify erase-rewrite cycle counter code to use a 4 byte counter
    instead of a two byte counter.


Version 2.1.0:

  * Implement a per-part erase-rewrite cycle counter; requires the use
    of two bytes of EEPROM memory.


Version 2.0.5:

  * Support for ATtiny15 - contributed by Asher Hoskins


Version 2.0.4:

  * Config file fixes for various parts.


Version 2.0.3:

  * Work around problem programming fuse bits on parts like the
    at90s4433 as described in the following errata:

      http://www.atmel.com/atmel/acrobat/doc1280.pdf

  * Add part definition for at90s4414, at90s4433.

  * Add fuse/lock bit memory instructions for the at90s1200,
    at90s2333, at90s4433 and at90s8515.

  * Fix setting of programmer status LEDs under certain write-fail
    conditions.


Version 2.0.2 :

  * Fix writing to read-only memories such as the lock bits of the
    AT90S2313.

  * Copyright updates.


Version 2.0.1 :

  * Use correct parallel port pins for VCC.

  * Add programmer definition for Atmel's STK200.

  * Add programmer definition for the AVR3 board.

  * Fix address bit encoding for many parts.

  * Allow the ``BUFF'' signal to be asserted by multiple pins of the
    parallel port (like VCC) instead of just one.  The STK200 appears
    to need this feature.


Version 2.0.0 :

  * Add support for programming fuse and lock bits if supported by the
    part.

  * Move instruction encoding into the config file.  Now any part can
    be supported as long as it uses the same basic serial programming
    instruction format.

  * Add part definitions for the ATMega163 and ATMega8 devices.


Version 1.4.3 :

  * Mostly internal code cleanup.


Version 1.4.2 :

  * Fixes for ATMega paged memory support.

  * Support for ATMega16 device.


Version 1.4.1 :

  * No functional changes, update to Copyrights only.


Version 1.4.0 :

  * Add part definitions to the config file.

  * Add initial support for Atmel's ATMega paged memory parts.

  * Config file documentation added.

  * Add a definition for the Dontronics DT006 programmer.

  * Fix Intel Hex support for addresses larger than 64k.


Version 1.3.0 :

  * Make programmer pin assignments configurable.


Version 1.2.2 :

  * Initial public release