avrdude/CHANGELOG

199 lines
5.4 KiB
Plaintext
Raw Normal View History

$Id$
Approximate change log for AVRDUDE by version
----------------------------------------------------------------------
Version 3.1.0
* This change represents a name change only. There is currently an
effort to port AVRPROG to other platforms including Linux and
Windows. Since Atmel's programmer binary that's included within
their AVR Studio software is named AVRPROG.EXE on the Windows OS,
there is the chance for confusion if we keep calling this program
AVRPROG as well. Up until now the name hasn't really been a
problem since there was no chance to confuse 'avrprog' on Unix
with Atmel's AVRPROG because Atmel's tools only run on Windows.
But with the Unix 'avrprog' possibly being ported to Windows, I
felt a name change was the best way to avoid problems.
So - from this point forward, my FreeBSD Unix program formerly
known as AVRPROG will subsequently be known as AVRDUDE (AVR
Downloader/UploaDEr).
This change also represents a time when the AVRDUDE sources move
from my own private repository to a public repository. This will
give other developers a chance to port AVRDUDE to other platforms
and extend its functionality to support additional programming
hardware, etc.
So goodbye AVRPROG, welcome AVRDUDE!
Version 3.0.0
* Rewrite parts of the code to make it easy to support other types
of programmers besides the directly connected parallel port
programmer (PPI).
* Add support for Atmel's STK500 programmer/development board. The
STK500's "paged mode" read/write is supported which makes this
programmer very fast. This is sorely needed on parts with large
memories such as the ATmega128. My 12K test program burns in
about 5 seconds, add another 5 to read it back out for
verification.
Version 2.1.5:
* When getting ready to initiate communications with the AVR device,
first pull /RESET low for a short period of time before enabling
the buffer chip. This sequence allows the AVR to be reset before
the buffer is enabled to avoid a short period of time where the
AVR may be driving the programming lines at the same time the
programmer tries to. Of course, if a buffer is being used, then
the /RESET line from the programmer needs to be directly connected
to the AVR /RESET line and not via the buffer chip.
Feature contributed by Rick C. Petty <rick@KIWI-Computer.com>.
* When in interactive terminal mode and dumping memory using the
'dump <memtype>' command without any address information, and the
end of memory is reached, wrap back around to zero on the next
invocation.
Version 2.1.4:
* Fix -Y option.
Version 2.1.3:
* Be backward compatible when reading 2-byte rewrite cycle counters
as written by avrprog version 2.1.0. Version 2.1.1 changed over
to a 4-byte counter, which caused avrprog versions 2.1.1 and 2.1.2
to report a negative count for parts that were initialized using
version 2.1.0. Thanks to Joerg Wunsch for noticing this.
Version 2.1.2:
* Add '-V' option to disable automatic verify check with uploading
data.
Version 2.1.1:
* Fix ATmega128 instruction sequences for reading fuse bits -
contributed by Joerg Wunsch.
* Modify erase-rewrite cycle counter code to use a 4 byte counter
instead of a two byte counter.
Version 2.1.0:
* Implement a per-part erase-rewrite cycle counter; requires the use
of two bytes of EEPROM memory.
Version 2.0.5:
* Support for ATtiny15 - contributed by Asher Hoskins
Version 2.0.4:
* Config file fixes for various parts.
Version 2.0.3:
* Work around problem programming fuse bits on parts like the
at90s4433 as described in the following errata:
http://www.atmel.com/atmel/acrobat/doc1280.pdf
* Add part definition for at90s4414, at90s4433.
* Add fuse/lock bit memory instructions for the at90s1200,
at90s2333, at90s4433 and at90s8515.
* Fix setting of programmer status LEDs under certain write-fail
conditions.
Version 2.0.2 :
* Fix writing to read-only memories such as the lock bits of the
AT90S2313.
* Copyright updates.
Version 2.0.1 :
* Use correct parallel port pins for VCC.
* Add programmer definition for Atmel's STK200.
* Add programmer definition for the AVR3 board.
* Fix address bit encoding for many parts.
* Allow the ``BUFF'' signal to be asserted by multiple pins of the
parallel port (like VCC) instead of just one. The STK200 appears
to need this feature.
Version 2.0.0 :
* Add support for programming fuse and lock bits if supported by the
part.
* Move instruction encoding into the config file. Now any part can
be supported as long as it uses the same basic serial programming
instruction format.
* Add part definitions for the ATMega163 and ATMega8 devices.
Version 1.4.3 :
* Mostly internal code cleanup.
Version 1.4.2 :
* Fixes for ATMega paged memory support.
* Support for ATMega16 device.
Version 1.4.1 :
* No functional changes, update to Copyrights only.
Version 1.4.0 :
* Add part definitions to the config file.
* Add initial support for Atmel's ATMega paged memory parts.
* Config file documentation added.
* Add a definition for the Dontronics DT006 programmer.
* Fix Intel Hex support for addresses larger than 64k.
Version 1.3.0 :
* Make programmer pin assignments configurable.
Version 1.2.2 :
* Initial public release